Search Results

In the future, it will be possible to manufacture very small, robust machines, which may be attached to the surface of a wing allowing the classic boundary condition of “no-slip” to be altered at will. It is also possible that the heat transfer through the wing surface can be controlled. This paper reports an investigation into the possible benefits to aerodynamics that will occur if such machines become available. It is found that imposing an isothermal wing surface can increase the lift drag ratio of wing at transonic cruise and allowing slip at the surface can have the same effect. Both these effects are additive. It is found that control of heat transfer on a wing at hypersonic wing can act as a control device, comparable to that due a moderate flap deflection.

The timing of lubricating oil changes for passenger vehicles are based on set time or mileage intervals specified by their manufacturers. A few vehicle manufacturers use more sophisticated methods such as logging the engine speed and temperature and calculating the oil change intervals from this data. Neither technique tells the vehicle user anything about the true state of the oil. A novel form of viscosity sensor based on a vibrating piezoceramic element has been developed. Based on the output from such a device, a more accurate determination of the oil change interval can be made and abnormal conditions (such as the leakage of fuels into the lubricating oil) can be detected. This paper gives a brief description of the device itself and shows results from prototype samples.

Driving cycles have been used in Federal Test Procedures to establish fuel economy and emissions characteristics for automobiles. Reasonable driving cycles for trucks and buses have been more difficult to establish because of the great variety of uses which these vehicles experience. The truck cycle has been divided into three different use categories—the local cycle, the short haul cycle, and the highway cycle. Only recently, has actual field data been obtained, and this paper proposes a method of utilizing this data to develop a more realistic local cycle than those previously proposed.

It is well known that the drilling industry is a diverse industry with huge power needs for drilling deep wells. This paper discusses the drilling industry in general and the future need for HT power electronics to enable such activities as tractor drive drilling of deep horizontal wells. The discussion is geared at applications for drilling within the earth at ambient temperatures of 150°C and above.

Of the many research approaches investigated over the years to measure the lubrication properties of aviation turbine fuels, the Ball-on-Cylinder Lubricity Evaluator (BOCLE) has emerged as the most significant test. BOCLE was originally a lubricant research device modified for low viscosity jet fuel when the Air Force encountered fuel control problems in 1965 with JP-4. It proved to be capable of detecting the presence of additives such as corrosion inhibitors which improve boundary lubrication properties and also the absence of natural lubricity agents in highly refined jet fuel. The Coordinating Research Council carried out several programs to investigate test variables such as cylinder type, humidity control and load. A semi-automated version using Falex test rings has now been commercialized and is being used to test fuels from aircraft experiencing abnormal pump wear and fuel control hang-up.

There is an ongoing interest in biodegradable hydraulic fluids. Biodegradable fluids are often considered to include only vegetable oils, polyol esters and diester base stocks. However, other fluid base stocks including highly refined mineral oils, poly(alpha olefins) and fire-resistant fluids such as water-glycol hydraulic fluids are also biodegradable fluid alternatives. This paper will provide an overview of the international literature on biodegradable fluids, various international testing protocol, fluid base stocks, effect of oxidative stability, material compatibility and pump performance.

Modern project management including brake testing includes the exchange of reliable results from different sources and different locations. The ISO TC22/SWG2-Brake Lining Committee established a task force led by Ford Motor Co. to determine and analyze root causes for variability during dynamometer brake performance testing. The overall goal was to provide guidelines on how to reduce variability and how to improve correlation between dynamometer and vehicle test results. This collaborative accuracy study used the ISO 26867 Friction behavior assessment for automotive brake systems. Future efforts of the ISO task force will address NVH and vehicle-level tests. This paper corresponds to the first two phases of the project regarding performance brake dynamometer testing and presents results, findings and conclusions regarding repeatability (within-lab) and reproducibility (between-labs) from different laboratories and different brake dynamometers.

The ISO TC22/SWG2 - Brake Lining Committee established a task force to determine and analyze root causes for variability during dynamometer brake performance testing. SAE paper 2010-01-1697 “Brake Dynamometer Test Variability - Analysis of Root Causes” [1] presents the findings from the phases 1 and 2 of the “Test Variability Project.” The task force was created to address the issue of test variability and to establish possible ways to improve test-to-test and lab-to-lab correlation. This paper presents the findings from phase 3 of this effort-description of factors influencing test variability based on DOE study. This phase concentrated on both qualitative and quantitative description of the factors influencing friction coefficient measurements during dynamometer testing.

A second carbonyl round robin was conducted to enable participating laboratories doing routine analysis of carbonyls in vehicle exhaust emissions to assess their analytical capabilities. Three sets of solutions in acetonitrile containing varying number and amounts of standard DNPH-carbonyls were prepared. The parent carbonyls are known components of vehicle exhaust emissions. The samples were designed to challenge the capabilities of the participants to separate, identify and quantify all the components. The fourteen participating laboratories included automotive, contract, petroleum and regulatory organizations. All participants were able to separate and identify the C3 carbonyls; a few were not able to separate MEK from butyraldehyde and methacrolein from butyraldehyde; and many were not able to separate adequately the isomers of tolualdehyde. Inadequate separation and lack of appropriate standards resulted in a few misidentifications.

Development of reliable magnesium (Mg) to steel joining methods is one of the critical issues in broader applications of Mg in automotive body construction. Ultrasonic spot welding (USW) has been demonstrated successfully to join Mg to steel and to achieve strong joints. In this study, corrosion test of ultrasonic spot welds between 1.6 mm thick Mg AZ31B-H24 and 0.8 mm thick galvanized mild steel, without and with adhesive, was conducted. Adhesive used was a one-component, heat-cured epoxy material, and was applied between overlapped sheets before USW. Corrosion test was conducted with an automotive cyclic corrosion test, which includes cyclic exposures of dipping in the 0.5% sodium chloride (NaCl) bath, a constant humidity environment, and a drying period. Lap shear strength of the joints decreased with the cycles of corrosion exposure. Good joint strengths were retained at the end of 30-cycle test.

The aerodynamics of the STOL aircraft can experience significant changes in proximity to the ground. A review of the existing data base and methodologies has been made and the results of that review are presented in this paper. The existing data show that in ground proximity the STOL aircraft will generally experience a reduction in the lift component regardless of the lifting configuration. Those configurations with integrated power and lift systems will have an additional effect of ground induced aerodynamic changes. This paper will discuss the existing data base and the deficiencies of that data base.

Reported tensile and fatigue properties of die cast AZ91D and AM60B magnesium alloys indicate that those values depend on the size and shape of the test samples and their global porosities. This paper reviews the mechanical properties reported in the open literature for these die cast alloys and indicates that section thickness and global porosity are inadequate for predicting the tensile and fatigue properties of die cast AZ91D and AM60B magnesium alloys.

Several of the authors have recently developed procedures to efficiently evaluate experimentally the relative contributions of various wind noise paths and sources. These procedures are described and, as a case study, results are provided for the noise in the interior of a production automobile subjected to wind tunnel airflow. The present measurements and analysis indicate that for the tested vehicle significant contributions to interior noise are provided by underbody and wheel well flows, radiation from the roof and seal aspiration. A significant tone associated with vortex shedding from the radio antenna was also noted.

This paper provides a review of the fatigue properties reported in the open literature for die cast magnesium-based alloys. Recently developed fatigue data, in the form of stress versus number of cycles to failure for bending fatigue (R=-1), are presented for die cast AM60B and AZ91D alloy specimens with thicknesses between 1 and 10 mm. The effects of specimen thickness and macrostructural features, such as porosity distributions and surface features (parting line and ejection pin marks), on the fatigue data are discussed.

Modern approaches to durability assurance in ground vehicle design are reviewed in the context of recent developments in computer-based analytical and experimental tools for use by designers and development engineers. Examples, using an automotive wheel assembly, are presented to illustrate the application of fatigue analysis in product development. Major challenges associated with the linking of various design tools into integrated networks appropriately configured for industrial problem solving are discussed along with an assessment of the potential benefits to be gained from such integration.

The purpose of this paper is to survey the adverse environmental impacts resulting from motor vehicles, to review technologies developed to address these problems, and to summarize the current status of pollution control programs around the world.

Rapidly industrializing developing countries are now starting to note similar air pollution problems to those of the industrialized world. This paper surveys the adverse environmental impacts resulting from motor vehicles, reviews technologies developed to address these problems, and summarizes the current status of pollution controls around the world. Special focus is on the design of strategies to address the emerging problems of developing countries.

Gear rattle, clunk, and other such noises, commonly referred to as impulsive or unusual noise, are often classified as unique problems without common origins. This paper examines the underlying structure that promotes them and traces physical system behaviors that predispose them to such noises. Though the audible noise itself is not modeled directly, a good deal of the disposable energy that sustains it can be inferred from the impulsive dynamics that underlies the whole process. Further effort quantifies the energies involved and appraises the distinctiveness of the perceived noise. Whether one hears gear rattle or clunk depends on the initiating site within the system and the impulsivity index of the prevailing dynamics. Observable indicators suggest that periodic noise is supported by periodic dynamics and, similarly, impulsive noise, by impulsive dynamics and that the latter is non-deterministic, discontinuous and even chaotic.

The efforts of the ISO “Test Variability Task Force” have been aimed at improving the understanding and at reducing brake dynamometer test variability during performance testing. In addition, dynamometer test results have been compared and correlated to vehicle testing. Even though there is already a vast amount of anecdotal evidence confirming the fact that different procedures generate different friction coefficients on the same brake corner, the availability of supporting data to the industry has been elusive up to this point. To overcome this issue, this paper focuses on assessing friction levels, friction coefficient sensitivity, and repeatability under ECE, GB, ISO, JASO, and SAE laboratory friction evaluation tests.

Development of Terrain-Vehicle Systems Analysis involving statistically variable ground, has necessitated the development of field instrumentation for mass measurement of soil parameter input. To this end, the idea originally conceived and tested at U.S. Army's Land Locomotion Laboratory in Detroit, was revived and adapted to modern requirements. The Wheeled Automated Bevameter (WAB) was presented as a better vehicle analog for measuring soil parameters than the conventional plate-shearing instrument hitherto used. It yields itself to mass production of terrain input, without which further progress in Terramechanics, based on statistical changes of the environment may be impossible.