Search Results

Catalyst systems utilizing ceramic and metallic substrates were compared to assess the influence of various substrate parameters on the exhaust gas conversion efficiency and flow restriction. In particular, the substrate surface area, substrate specific heat capacity, and substrate volume were all evaluated for their importance in estimating the conversion efficiency of the catalyst system. Additionally, substrate open frontal area and cell hydraulic diameter were compared against exhaust restriction performance.

Proper electric and thermal management of an HEV battery pack, consisting of many modules of cells, is imperative. During operation, voltage and temperature differences in the modules/cells can lead to electrical imbalances from module to module and decrease pack performance by as much as 25%. An active battery management system (BMS) is a must to monitor, control, and balance the pack. The University of Toledo, with funding from the U.S. Department of Energy and in collaboration with DaimlerChrysler and the National Renewable Energy Laboratory has developed a modular battery management system for HEVs. This modular unit is a 2nd generation system, as compared to a previous 1st generation centralized system. This 2nd generation prototype can balance a battery pack based on cell-to-cell measurements and active equalization. The system was designed to work with several battery types, including lithium ion, NiMH, or lead acid.

An overview is given on the state of the art of a new catalytic exhaust gas aftertreatment device for diesel engines. The function of a precious metal based, flow-through type diesel oxidation catalyst is explained. Much attention is paid to the durability of the diesel oxidation catalyst and especially to the influence of poisoning elements on the catalytic activity. Detailed data on the interaction of poisoning elements such as sulfur, zinc and phosphorus with the catalytic active sites are given. Finally it is demonstrated that it is possible to meet the stringent emission standards for diesel passenger cars in Europe with a new catalyst generation over 80.000 km AMA aging.

The California LEV1 II program will be introduced in the year 2003 and requires a further reduction of the exhaust emissions of passenger cars. The cold start emissions represent the main part of the total emissions of the FTP2-Cycle. Cold start emissions can be efficiently reduced by injecting secondary air (SA) in the exhaust port making compliance with the most stringent standards possible. The thermochemical conditions (mixing rate and temperature of secondary air and exhaust gas, exhaust gas composition, etc) prevailing in the exhaust system are described in this paper. This provides knowledge of the conditions for auto ignition of the mixture within the exhaust manifold. The thus established exothermal reaction (exhaust gas post-combustion) results in a shorter time to light-off temperature of the catalyst. The mechanisms of this combustion are studied at different engine idle conditions.

To date, several non-SCR catalysts and catalytic systems have been suggested for NOX reduction under oxygen rich (lean) conditions, such as those which exist in diesel engine exhaust gas. However, the performance of such catalysts and catalyst systems is not clear when used on actual diesel engines. This paper reports on experimental results obtained when lean NOx catalysts are applied to diesel engine exhaust. Particularly, the catalysts' NOx performance is examined when secondary hydrocarbons are added as reducing agents directly in the exhaust gas stream. In addition, the effect of different catalyst formulations and secondary hydrocarbon addition on particulate emissions is monitored. Finally, partial system optimization is performed and the applicability of such catalysts and systems to engines operating under the US Heavy Duty Transient Cycle is examined.

Today the worldwide convergence towards stricter fuel consumption and emission regulations is pushing carmakers and suppliers into new fields of innovation. Valeo Engine Cooling, VEC, is contributing towards these goals by applying its thermal management system expertise in order to reduce fuel consumption and emissions by using an advanced engine cooling system that incorporated variable speed PWM fans, an electric water pump and an electric water control valve. The paper discusses the benefits in terms of engine cooling, fuel economy and emissions over the FTP drive cycle. The paper gives some examples of advanced engine cooling strategies based on a virtual, predictive metal temperature sensor that is used to actuate the electrical water pump at the desired flow rate. The electrical balance between the 42V pump and fans has also been optimized to reduce the vehicle electrical power consumption and to keep the coolant temperature close to 110°C.

Since the mechanisms leading to cyclic combustion variabilities in direct injection gasoline engines are still poorly understood, advanced computational studies are necessary to be able to predict, analyze and optimize the complete engine process from aerodynamics to mixing, ignition, combustion and heat transfer. In this work the Scale-Adaptive Simulation (SAS) turbulence model is used in combination with a parameterized lagrangian spray model for the purpose of predicting transient in-cylinder cold flow, injection and mixture formation in a gasoline engine. An existing CFD model based on FLUENT v15.0 [1] has been extended with a spray description using the FLUENT Discrete Phase Model (DPM). This article will first discuss the validation of the in-cylinder cold flow model using experimental data measured within an optically accessible engine by High Speed Particle Image Velocimetry (HS-PIV).

Several different possibilities will be described and discussed on the processes of reducing NOx in lean-burn gasoline and diesel engines. In-company studies were conducted on zeolitic catalysts. With lean-burn spark-ignition engines, hydrocarbons in the exhaust gas act as a reducing agent. In stationary conditions at λ = 1.2, NOx conversion rates of approx. 45 % were achieved. With diesel engines, the only promising variant is SCR technology using urea as a reducing agent. The remaining problems are still the low space velocity and the narrow temperature window of the catalyst. The production of reaction products and secondary reactions of urea with other components in the diesel exhaust gas are still unclarified.

This paper reports first results of research and development work to achieve Nox reduction under lean diesel exhaust gas conditions by using a special coated, zeolite based monolith catalyst. Much attention is paid to the optimization of the activated zeolite system and the influence of group Ib and VIII elements of the periodic system. A major part of the paper deals with the influence of hydrocarbons, carbon monoxide, sulfur dioxide and water on the activity of the catalyst. Another aspect discussed is the influence of the residence time of the exhaust gas components. The thermal stability and the influence of poisoning elements on the catalyst performance is demonstrated by model gas reactor tests on oven and engine aged samples. Finally, first results on the performance of the catalyst system in a vehicle dynometer test are given.

This paper compares 4 different EGR systems by means of simulation in GT-Power. The demands of optimum massive EGR and fresh air rates were based on experimental results. The experimental data were used to calibrate the model and ROHR, in particular. The main aim was to investigate the influence of pumping work on engine and vehicle fuel consumption (thus CO2 production) in different EGR layouts using optimum VG turbine control. These EGR systems differ in the source of pressure drop between the exhaust and intake pipes. Firstly, the engine settings were optimized under steady operation - BSFC was minimized while taking into account both the required EGR rate and fresh air mass flow. Secondly, transient simulations (NEDC cycle) were carried out - a full engine model was used to obtain detailed information on important parameters. The study shows the necessity to use natural pressure differences or renewable pressure losses if reasonable fuel consumption is to be achieved.

Researchers at the National Renewable Energy Laboratory conducted outdoor vehicle thermal soak tests in Golden, Colorado, in September 2002. The same environmental conditions and vehicle were then tested indoors in two DaimlerChrysler test cells, one with metal halide lamps and one with infrared lamps. Results show that the vehicle's shaded interior temperatures correlated well with the outdoor data, while temperatures in the direct sun did not. The large lamp array situated over the vehicle caused the roof to be significantly hotter indoors. Yet, inside the vehicle, the instrument panel was cooler due to the geometry of the lamp array and the spectral difference between the lamps and sun. Results indicate that solar lamps effectively heat the cabin interior in indoor vehicle soak tests for climate control evaluation and SCO3 emissions tests. However, such lamps do not effectively assess vehicle skin temperatures and glazing temperatures.

To support the application and design of exhaust gas aftertreatment systems for gasoline fueled passenger cars based on hydrocarbon adsorber catalysts, a computer model was developed. This model is based on simplified, lumped kinetics for the adsorption and desorption of hydrocarbons and for the oxidation of CO and hydrocarbons. Also included in the model are convective transport of heat and mass in the gas phase, mass and heat transfer to the washcoat layer, and diffusion with reaction in the washcoat layer. The continuity equations for this model with the appropriate boundary conditions were solved for a single channel assuming adiabatic behavior. After validation of the prediction on experimental results, this model was used to perform a simple parametric study on the influence of inlet temperature,CO concentration, washcoat loading, adsorber content, and cell density on the HC emission.

The regulations for mobile applications will become stricter in Euro 6 and further emission levels and require the use of active aftertreatment methods for NOX and particulate matter. SCR and LNT have been both used commercially for mobile NOX removal. An alternative system is based on the combination of these two technologies. Developments of catalysts and whole systems as well as final vehicle demonstrations are discussed in this study. The small and full-size catalyst development experiments resulted in PtRh/LNT with optimized noble metal loadings and Cu-SCR catalyst having a high durability and ammonia adsorption capacity. For this study, an aftertreatment system consisting of LNT plus exhaust bypass, passive SCR and engine independent reductant supply by on-board exhaust fuel reforming was developed and investigated. The concept definition considers NOX conversion, CO2 drawback and system complexity.

The implementations of the Tier 2 and LEVII emission levels require fast catalyst light-off and fast closed loop control through high-speed engine management. The paper describes the development of innovative catalyst designs. During the development thermal and mechanical boundary conditions were collected and component tests conducted on test rigs to identify the emission and durability performance. The products were evaluated on a Super Imposed Test Setup (SIT) where thermal and mechanical loads are applied to the test piece simultanously and results are compared to accelerated vehicle power train endurance runs. The newly developed light-off catalyst with Perforated Foil Technology (PE) showed superior emission light-off characteristic and robustness.

The present paper describes the results of a joint development program focussing on a system approach to meet the proposed EURO III and IV emission standards for a passenger car equipped with a 3.2 liter, 18 valve gasoline engine. Starting with the in-production configuration of a EURO II certified vehicle (model year 1997) the following improvement points were investigated in detail. By the introduction of a close-coupled catalyst in combination with engine measures to improve the catalyst light-off the proposed EURO III limits were met. The proposed EURO IV hurdle could be overcome by further using secondary air injection during cold-start in combination with an increased precious metal loading for the close-coupled catalyst.

SOF and de-NOx catalysts are applied to heavy-duty diesel trucks which are regulated by European 13 mode or Japanese 13 mode cycles. Precious metal free catalysts can reduce SOF at low temperatures without increasing sulfates up to 670C. This catalyst shows little deterioration after 400 hours of high temperature engine aging. 32% PM and 47% SOF reduction is observed under 13 mode tests when the exhaust gas temperature exceeds 700C (ECE-13 mode). This precious metal free catalyst is suitable for diesel trucks, especially trucks with natural aspirating engine whose exhaust gas temperature is very high. De-NOx catalysts with a 300-500C NOx reduction temperature window are applied to the Japanese heavy-duty test cycle (Japan 13 mode). When secondary diesel fuel is added under modes 8 to 12, (secondary fuel addition only when catalyst inlet temperature is more than 300C), 19-25% NOx can be reduced with 2-4% fuel penalty.

Fundamental research work was undertaken to elucidate the mechanism of hydrogen sulfide formation on three-way automotive exhaust catalysts during the lean to rich engine operation sequence and to identify the role of the different catalyst components in this phenomenon. Based upon this knowledge, new catalysts were developed with reduced ability to form hydrogen sulfide by minimizing the storage of sulfur oxides. Engine dynamometer tests confirmed that the suppression of the hydrogen sulfide formation was obtained without loss of catalyst activity or aging stability. The role of the catalyst's age in the hydrogen sulfide formation is discussed. The development presented shows that it is possible to avoid “scavengers” to minimize the emission of hydrogen sulfide from three-way emission control catalysts.

Diesel particulate mass emissions and their corresponding size distributions have been investigated on a diesel passenger car at steady state conditions using standard filters and a cascade impactor. These tests have been carried out at two different engine operating conditions (2100 rpm, 2.7 and 13.3 kW, respectively) corresponding to low and high exhaust gas temperatures. Two diesel fuels differing in their sulfur content (150 ppm and 2500 ppm S) have been used for these investigations. The particulate size distribution after diesel oxidation catalyst was found to be affected by the sulfur content of the diesel fuel and by the exhaust gas temperature. Interpretations of these results on a mechanistic basis are given. The diesel particulate emission studies have been extended to dynamic vehicle tests.

The introduction of gasoline direct injection technology into the European market will depend mainly on the availability of an effective and durable aftertreatment system, in order to reach future stringent European emission standards. NOx storage technology provides a reasonable chance of fulfilling future emission goals, but durability problems such as thermal degradation and sulfur poisoning have yet to be overcome. The present paper is dedicated to these problems, and demonstrates the progress achieved so far. The influence of different aging modes and aging severity on the NOx conversion efficiency of an advanced generation of NOx storage catalysts, is described in detail. It was found that the severity of aging at comparable catalyst bed temperatures, increases in the following order: hydrothermal aging in N2/H2O < engine aging w/o fuel cut at λ-1 < furnace aging in air < engine aging with fuel cut at λ-1.

The spray development, combustion and emissions in a 1.9L optical, four-cylinder, direct-injection diesel engine were investigated by means of pressure analysis, high-speed cinematography, the two-colour method and exhaust gas analysis for various levels of exhaust gas recirculation (EGR), three EGR temperatures (uncontrolled, hot and cold) and three fuels (diesel, n-heptane and a two-component fuel 7D3N). Engine operating conditions included 1000 rpm/idle and 2000 rpm/2bar with EGR-rates ranging from 0 to 70%. Independent of rate, EGR was found to have a very small effect on spray angle and spray tip penetration but the auto-ignition sites seemed to increase in size and number at higher EGR-rates with associated reduction in the flame luminosity and flame temperature, by, say, 100K at 50% EGR.