Search Results

This paper investigates the potential of using FEA poro-elastic Biot elements for the modeling carpet-like trim systems in a simplified setup. A comparison between FEA computations and experiments is presented for two layer (mass-spring) trim systems placed on a test-rig consisting in a 510×354×1.6 mm flat steel plate clamped in a stiff frame excited at its base. Results are presented for a given heavy layer with two different poro-elastic materials: one foam and one fibrous material. The investigations included accelerometer measurements on the steel plate, laser-doppler vibrometer scans of the heavy layer surface, sound pressure measurements in free field at a distance of 1 meter above the plate, as well as sound pressure in a closed rectangular concrete-walled cavity (0.5×0.6×0.7 m) put on top of the test-rig. Computations were carried out using a commercial FEA software implementing the Biot theory for poro-elastic media.

In this paper, responses from a vehicle's suspension, chassis and body, are used to demonstrate a methodology to optimize physical test results. It is well known that there is a variability effect due to an increase of wheel unsprung mass (due to loads measurement fixturing), tire pressure, speed, etc. This paper quantifies loading variability due to Wheel Force Transducer (WFT) unsprung mass by using a rainflow cycle counting domain. Also, presents a proving ground-to-test correlation study and the data reduction techniques that are used in road simulation test development to identify the most nominal road load measurement. Fundamental technical information and analytical methodology useful in overall vehicle durability testing are discussed. Durability testing in a laboratory is designed to correlate fatigue damage rig to road. A Proving Ground (PG) loading history is often acquired by running an instrumented vehicle over one or more PG events with various drivers.

The LEV II and SULEV/PZEV emission standards legislated by the US EPA and the Californian ARB will require continuous reduction in the vehicles' emission over the next several years. Similar requirements are under discussion in the European Union (EU) in the EU Stage V program. These future emission standards will require a more efficient after treatment device that exhibits high activity and excellent durabilty over an extended lifetime. The present study summarizes the findings of a joint development program targeting such demanding future emission challenges, which can only be met by a close and intensive co-operation of the individual expert teams. The use of active systems, e.g. HC-adsorber or electrically heated light-off catalysts, was not considered in this study. The following parameters were investigated in detail: The development of a high-tech three-way catalyst technology is described being tailored for applications on ultra thin wall ceramic substrates (UTWS).

In the automotive industry, the model-based approach is increasingly establishing itself as a standard paradigm for developing control unit software. Just as code reviews are widespread in classical software development as a quality assurance measure, models also have to undergo a stringent review procedure – particularly if they serve as a starting point for automatic implementation by code generators. In addition to these model reviews, the generated production code is reviewed later in the development process by performing auto code reviews. This article will present procedures for and give an account of experiences with model and code reviews which have been adapted to the model-based development process.

An assessment of stamped part quality and launch readiness occurs at many intervals. This paper will focus on dimensional control activities that take place after Stamping Dies are constructed, but prior to producing the stamped parts. Die certification and die repeatability measurements have been performed at DaimlerChrysler and the results are documented. This die certification process provides an opportunity to uncover and resolve die machining issues with respect to the part math model or pre-engineered compensation model prior to producing parts. Additionally, the die repeatability process is performed to determine the ability of the die gaging to locate the incoming in-process material consistently. This paper will explain the die certification and die repeatability processes and share what we have learned. It will describe the processes, the tools, the participants, the sites, the benefits, and the measurement equipment.

Hot Isostatic Pressing (HIP) has been routinely used to densify castings for aerospace and medical applications for over 30 years. While HIP is widely known to improve the toughness and fatigue life of castings through the healing of internal porosity, it has been perceived as too expensive for most cast aluminum alloys for automotive applications. Recent developments suggest that the cost effectiveness of certain special HIP processes should be revisited due to reductions in process cost and improvements in throughput. This paper will evaluate the Densal® II process applied to a front aluminum steering knuckle. Two casting processes representing differing levels of relative cost and quality were evaluated. The first was Alcoa's VRC/PRC process, a metal mold process with bottom fill, evacuation before fill and pressurization after fill. This is considered to be a premium quality, but higher cost casting process that is already qualified for this application.

This paper describes work supporting the development of a new Diesel particulate trap system for heavy duty vehicles based on porous sintered metal materials that exhibit interesting characteristics with respect to ash tolerance. Experimental data characterizing the material (permeability, soot and ash deposit properties) are obtained in a dedicated experimental setup in the side-stream of a modern Diesel engine as well as in an accelerated ash loading rig. System level simulations coupling the new media characteristics to 3-D CFD software for the optimization of complete filter systems are then performed and comparative assessment results of example designs are given.

Traditionally, high-strength low-alloy (HSLA) steel is used for automotive vehicle weight reduction in the North American automotive industry. Dual phase (DP) high strength steel has gained great attention because it provides a combination of high strength and good formability. The main advantage of DP steel is the high ratio of tensile strength to yield strength, which provides more flexibility in stamping and higher energy absorption in a component crush event. This study compares the performances of DP and HSLA steel grades in stamping processes and component crush events, as shown in a typical automotive unibody inner rail. Simulation results show that DP steel offers more uniform strain distribution, improved formability, and better crush performance than conventional HSLA steel.

A Draw Bead Simulator (DBS), with modified draw beads, was employed in this study to understand the springback behavior of sheet metal subjected to multiple bending-unbending cycles. The investigations were carried out in both the rolling and the transverse rolling directions on four types of materials: Electro-Galvanized DQ steel, light and heavy gauge Hot-Dip Galvanealed High Strength Steels, and Aluminum alloy AL6111. The sheet geometries, thickness strains, pulling forces and clamping forces were measured and analyzed for the purpose of establishing a benchmark database for numerical predictions of springback. The results indicate that the springback curvature changes dramatically with the die holding force. The conditions at which the springback is minimized was observed and found to depend on the material properties and the sheet thickness. Analysis with an implicit FEM showed that the predicted and the experimental results are in very good agreement.

Silicon Carbide (SiC) based high temperature semiconductor gas sensors were tested for potential applications in the closed-loop control of NOx storage catalytic converters. The exhaust gas composition behind a storage catalyst was simulated by synthetic gas mixtures supplied from a gas blending manifold. In lean oxidizing ambients the sensors produced signals opposite in sign upon the appearance of NOx on the one hand and mixtures of HC and CO on the other hand. Transient gas measurements revealed response times ranging between several milliseconds for HC and several seconds for NOx. These features render SiC based sensors potentially useful for the control of NOx storage catalytic converters.

The staircase fatigue testing method is a recognized method for determining the fatigue limit of powertrain components. The purpose of this paper is to improve upon existing standards by adding common practices that will ensure a higher degree of statistical accuracy in the data. This includes specifying appropriate sample sizes, stress increments and initial load conditions, as well as making suggestions for appropriate methods of analyzing the data. Two methods (Dixon and Mood method and probit analysis method) are selected and compared in terms of relative percent difference on four parameters (mean, standard deviation, B10 fatigue strength and B50 fatigue strength). The staircase data are obtained by simulations from normal and lognormal fatigue limit distributions.

Sheet metal stamping involves a system of complex tribological (friction, lubrication, and wear), heat transfer, and material strain interactions. Accurate coefficient of friction, strain, and lubrication regime data is required to allow proper modeling of the various sheet stamping processes. In addition, non-intrusive means of monitoring the coefficient of friction in production stamping operations would be of assistance for efficiently maintaining proper stamping quality and to indicate when adjustments to the various stamping parameters, including maintenance, would be advantageous. One of the key sub-systems of the sheet metal stamping process is the draw bead. This paper presents an investigation of the tribology of the draw bead using a Draw Bead Simulator (DBS) Machine and automotive zinc-coated sheet steels. The investigation and findings include: 1) A new, non-intrusive method of measuring the surface temperature of the sheet steel as it passes through the draw bead.

The influence of adsorption and desorption processes on the non-thermal plasma enhanced catalytic reduction of NOx on NaZSM5- and Al2O3-based lean-NOx catalysts (Pt-NH4ZSM5, Cu-NaZSM5, Fe-NaZSM5, Pt-Al2O3, Pd-Al2O3, CuO-Al2O3, Ag-Al2O3) was investigated by temperature programmed reaction experiments in the temperature range from 100 °C to 600 °C. Dodecane was used as a reducing agent. Strong HC adsorption- and desorption effects were observed on the zeolite catalysts, which were not influenced by plasma-pretreatment. Adsorption of NO2 and desorption of NO occurred on Al2O3-based catalysts. By plasma-pretreatment adsorption of NO2 was induced at low temperatures. NOx-reduction rates of the catalysts Cu-NaZSM5, Fe-NaZSM5, and the Ag-Al2O3 were increased substantially by plasma-pretreatment. Both plasma-induced and catalytic oxidation of HCs were limiting factors of the NOx-reduction obtained on these catalysts.

Even with the rapidly evolving computational tools available today, suspension design remains very much a black art. This is especially true with respect to road cars because there are so many competing design objectives. In a racecar some of these objectives may be neglected. Even still, just concentrating on maximizing road-holding capability remains a formidable task. This paper outlines a procedure for establishing suspension parameters, and includes a computational example that entails spring, damper, and anti-roll bar specification. The procedure is unique in that it not only covers the prerequisite vehicle dynamic equations, but also outlines the process that sequences the design evolution. The racecar design covered in the example is typical of a growing number of small open wheel formula racecars, built specifically for American autocrossing and British hillclimbs.

Mercedes-Benz at DaimlerChrysler has been developing and applying Life-Cycle-Engineering (LCE) and Life-Cycle-Assessment (LCA) since almost 10 years. Extensive experience and know-how has been gained by two complete car LCAs and more than 100 LCAs for parts. According to our experience LCA/LCE is most effectively and efficiently used to support the development of new products. One of DaimlerChrysler's Environmental Guidelines includes a statement, that our approach to environmentally acceptable design covers the entire product spectrum of the DaimlerChrysler Group, taking into account the product life cycle from design through disposal or recycling. The organisation of environmental management at DaimlerChrysler has a distinct structure of tasks: the central Environmental Protection Division coordinates all organisation/ plant related aspects, while all product related aspects are the responsibility of the divisonal business units.

In response to ever more stringent emission limits (EURO IV, SULEV), engine developers are increasingly turning their attention to engine start-up and warm-up phases. Since in this phase the catalytic converter has not yet reached its operating temperature, problems occur especially with regard to hydrocarbon emissions (HC) which are emitted untreated. Secondary air injection represents one option for heating up the catalytic converter more quickly. The engine is operated during the heating up cycle with retarded ignition angles and a rich mixture. Ambient air (secondary air) is injected close to the exhaust valve seat. During the spontaneously occurring post oxidation phase, the reactive exhaust components ignite and heat up the catalytic converter while simultaneously reducing HC. The various processes which affect the post oxidation, are not well known up to now. In order to achieve concrete improvements, detailed knowledge of its influences are necessary.

The recent trends of increasing driveline torque and use of traction control devices call for increasingly higher durability capacity from driveline components. Bench and vehicle durability tests are often used to validate designs, but they are not cost-effective and take months to complete. Traditional finite element analysis (FEA) procedures have been used effectively in the re-design of driveline components to reduce stress, and occasionally, to predict fatigue life. But in the case of certain rotating components, such as the Axle Differential Case, where the component sees large stress/strain fluctuations within the course of one complete rotation, even under constant input torque, historical fatigue analysis (when conducted) yields very conservative results. The axle differential case tends to be one of the weakest links in the rear axle assembly. Therefore, there is a crucial need for analytical methods to more accurately predict fatigue life to reduce testing time and cost.

This paper evaluates several durability tire models using Virtual Tire Testing (VTT) strategy. VTT conducts tire testing (simulation) using LS–DYNA based on a Virtual Tire which is built by 3–D finite element mesh. VTT is repeatable and could do special tire tests which can't be done using normal tire testing bench. A brief review is given on durability tire models and several typical tire models are selected for this study. All the necessary parameters for establishing the analytical tire models are extracted from the Virtual Tire. Quarter vehicle model is used to simulate the vehicle vertical vibration. The comments of those analytical tire models are given based on their performance vs. VTT.

The effect of forming strains on the fatigue behavior of an automotive mild steel, interstitial free steel, was studied after being prestrained by balanced biaxial stretch and plane strain. In the long life region, higher than 5×105 reversals, prestrain improves fatigue resistance. In the short life region, prestrain reduces fatigue resistance. At even shorter fatigue lives, the detrimental effect of prestrain diminishes. For plane strains, the fatigue behavior is anisotropic. In the direction perpendicular to the major strain, the steel exhibits much better fatigue resistance than in the direction parallel to the major strain.

To correlate data collected at multiple sites when using flexible fixturing to position parts for a CMM (Coordinate Measurement Machine), there are additional factors to consider and coordinate than when using CMM Holding Fixtures.