Search Results

A 10-foot-long fuselage section from a Boeing 737-100 airplane was dropped from a height of 14 feet generating a final impact velocity of 30 feet per second. The fuselage section was configured to simulate the load density at the maximum takeoff weight condition. The final weight of 8870 pounds included cabin seats, dummy occupants, overhead stowage bins with contents, and cargo compartment luggage. The fuselage section was instrumented with strain gages, accelerometers, and high-speed cameras. The fuselage sustained severe deformation of the cargo compartment. The luggage influenced the manner in which the fuselage crushed, affecting the gravitational (g) forces experienced by the test section. The seat tracks experienced 15 g's vertical deceleration. Although numerous fuselage structural members fractured during the test, a habitable environment was maintained for the occupants, and the impact was considered survivable.

Many of the certification regulations in 14 CFR Part 25 are by design, broad and as such, can be subject to large differences in the interpretation of what constitutes adequate compliance. Advisory Circulars (AC's) were developed for many of the regulations to assist industry, as well as certification personnel, with what is considered an acceptable, but not the only means, of compliance. However, there are many regulations where no advisory material is available. In these cases, the “acceptable means” of compliance can vary to a greater degree among the various aircraft certification offices. This difficulty is aggravated as new applicants and regulatory personnel enter the certification field. Recent discussions and interpretations on the usage of an avionic unit's mean time between failure or MTBF for its detectable faults as the basic repair rate for undetected or latent faults, is a subject area where no significant advisory material exists.

The FAA Office of Aviation Medicine has developed, delivered, and tested a variety of training systems over the past decade. The systems, their design, and guidance materials are directly transferable to the aviation industry at no cost. This paper describes the many training systems that are available.

The rapid growth in digital computer technology and display systems has impacted most aerospace disciplines. The designer manufacturer operator and even airplane passengers are all affected by this technology boom. The FAA in its role of certifying new aerospace products is no exception. This paper will emphasize the changing methodology of the FAA certification process with some specific examples of recent flight test programs.

As a part of its International Aging Aircraft Research Program, the Federal Aviation Administration is establishing a state-of-the-art Flight Loads Data Collection Program. Data collected in this program will provide the necessary mission profiles and load spectra information to characterize typical fleet service usage for the regional/commuter service life extension program. In addition, these data are applicable for both a safe life fatigue analysis and a damage tolerance fracture mechanics analysis. This paper describes the FAA approach and schedule for instrumenting fleet service aircraft, and the data reduction process.

The present regulatory tool for assessment of aircraft smoke emission, the Ringelmann Chart, is described; some of the shortcomings associated with its use for aircraft are discussed; research and development efforts to improve on this system are described. The gaseous pollutants, their relative importance in an airport area and research underway or needed is also discussed.

This paper describes the recently established Commercial Aviation Alternative Fuel Initiative (CAAFI), including its goals and objectives, as well as presents an alternate fuel roadmap that was originally generated by industry and refined by the CAAFI stakeholders. CAAFI is designed to coordinate the development and commercialization of “drop-in” alternate fuels (i.e. fuels that can directly supplement or replace crude oil derived jet fuels), as well as exploring the long-term potential of other fuel options. The ultimate goal is to ensure an affordable and stable supply of environmentally progressive aviation fuels that will enable continued growth of commercial aviation. This initiative is organized into four sub-groups: Research and Development (R&D), certification, environment, and economics & business. The R&D group seeks to identify promising new drop-in alternate fuels, and to foster coordination of development efforts.

The Federal Aviation Administration has placed increasing emphasis on modern information systems to achieve safety improvements. The ASAS (Aviation Safety Analysis System) is a comprehensive new system to upgrade significantly the agency's ability to collect process and disseminate safety-related information.

The crash impact characteristics of commuter category airplanes has recently been established using empirical procedures based on full scale aircraft impact test data for a range of aircraft sizes[1]. To compliment that empirical approach the Federal Aviation Administration (FAA) initiated a full scale commuter category airplane vertical impact test program. Those airplane vertical impact tests were structured to evaluate the airframe's capability to maintain its structural integrity and provide a protective shell for its occupants, to quantify the acceleration impact response characteristics of the airframe, and to evaluate the means necessary to provide occupant pelvic/lumbar column load injury protection up to the limits of survivable impact conditions.

In view of the fact that future generations of derivative or new aircraft will be faced with problems of increasing operating efficiency, new and more advanced technology will have to be introduced. To this end, the Federal Aviation Administration has been examining the certification question and has concluded that simulation may be increasingly important in the future certification activities. Through a contract with Lockheed Aircraft Company, the FAA will be able to review past use of industrial simulation in connection with certification.

In the early design stages of the advanced technology high-bypass-ratio engines, it became evident that maintainability considerations and more effective maintenance concepts would be necessary to achieve higher reliability and more economically successful powerplants. This paper reviews the major design considerations from a maintainability standpoint. It describes the concepts developed specifically to provide more effective maintenance for the wide-body jets. It discusses the effectiveness of these programs, and provides an insight into new philosophies and trends envisioned by the Federal Aviation Administration for future maintenance management programs.

High Ice Water Content (HIWC) has been identified as a primary causal factor in numerous engine events over the past two decades. Previous attempts to develop a remote detection process utilizing modern commercial radars have failed to produce reliable results. This paper discusses the reasons for previous failures and describes a new technique that has shown very encouraging accuracy and range performance without the need for any modifications to industry’s current radar design(s). The performance of this new process was evaluated during the joint NASA/FAA HIWC RADAR II Flight Campaign in August of 2018. Results from that evaluation are discussed, along with the potential for commercial application, and development of minimum operational performance standards for future radar products.

One Engine Inoperative takeoff climb performance of the XV-15 tilt rotor aircraft was analytically determined from level flight data and compared to the proposed powered-lift aircraft criteria. The results of this analysis can be useful in establishing the takeoff profile and highlighting potential certification issues.

In 2021 the Federal Aviation Administration in collaboration with the National Research Council of Canada performed research on altitude ice crystal icing of aircraft engines using the modular compressor rig, ICE-MACR, in an altitude wind tunnel. The aim of the research campaign was to address research needs related to ice crystal icing of aircraft engines outlined in FAA publication Engine Ice Crystal Icing Technology Plan with Research Needs. This paper reports the findings on ice accretion from a configuration of ICE-MACR with two compression stages. Inherent in two-stage operation is not just additional fracturing and heating by the second stage but also higher axial velocity and potentially greater centrifuging of particles. These factors influence the accretion behavior in the test article compared to single stage accretion.

Although Unmanned Aircraft Systems (UAS) have now for some time been used in segregated airspace where separation from other air traffic can be assured, potential users have interests to deploy UAS in non segregated airspace. Recent technological and operational improvements give reason to believe that UAS safety and performance capabilities are maturing. But the skies can only really open up to UAS when there is an agreed upon UAS safety policy with commonly accepted UAS Safety Risk Management (SRM) processes enabling to show that the risks related to UAS operations in all the different airspace classes can be adequately controlled. The overall objective is to develop a UAS SRM framework, supporting regulators and applicants through provision of detailed guidelines for each SRM step to be conducted, including 1) system description, 2) hazard identification, 3) risk analysis, 4) risk assessment, 5) risk treatment.

This paper compares the flammability of plastic automotive components to that of commodity, engineering, and specialty plastics as well as those used in commercial aircraft cabins with regard to performance in microscale combustion calorimetry tests. Not surprisingly, automotive components used in engine and passenger compartments are as flammable and ignitable as the commodity and engineering plastics of which they are made and much more flammable than those used in the interiors of aircraft.

Numerical simulations indicate that blast loading on aircraft structural joints can impart loading rates in excess of 10 Mlb/sec (ten million pounds per second, Reference 1). Experimental evidence, on the other hand, suggests that mechanical joint failure loads are highly loading rate dependent; for example, the failure load for a dynamically loaded tension joint can double from its static value. This paper discusses the progress and to-date findings of research on the assessment of strength failure of aircraft structural joints subjected to loading rates expected from an internal explosive detonation, and several associated experimental procedures to generate such dynamic loading. This work is conducted at MDC and at the University of Dayton Research Institute (UDRI) in support of the FAA Aircraft Hardening Program.

The Federal Aviation Administration is charged with the promotion of aviation safety. It is made up of three levels of administration within which are the functional organizations that manage the FAA programs and services. The Flight Standards service, which develops and enforces all regulations affecting aircraft and airmen, is the functional organization directly responsible for promoting aviation safety. This paper describes the Flight Standards aviation safety program.

The advent of digital electronics for use in civil aircraft, particularly the new technology represented by central processor and microprocessor controlled systems, represents a major challenge to the aviation industry. The Federal Aviation Administration (FAA) is charged with the responsibility of evaluating these systems to determine if they can be used safely. The complexity of these systems as compared to their analog counterparts in use today makes their evaluation difficult. This paper outlines the major concerns of the FAA with the use of software controlled digital systems for airborne applications. The methods which can be used by members of the aviation industry to obtain FAA certification of these systems are also discussed. The proposal of Special Committee SC-145 of the Radio Technical Commission for Aeronautics (RTCA) form the basis of the design methodology which is described for the successful development of the computer programs (software) to be used by these systems.

Federal Aviation Administration philosophy regarding simulator use in the airman certification system is stated. Airman certification requirements, specified in the Federal Aviation Regulations, are expressed in behavioral terms. Distinctions between simulator uses for training, evaluation, and gaining operational experience are discussed. A methodology for determining systematically and objectively how simulators may be used for pilot performance evaluation is derived from instructional system design. An experimental design, appropriate for validation studies of pilot performance evaluations in simulators, is referenced.