Search Results

The current ability of the Virtual Aerodynamic/ Aeroacoustic Wind Tunnel to predict interior vehicle sound pressure levels is demonstrated using an automobile model which has variable windshield angles. This prediction method uses time-averaged flow solutions from a lattice gas CFD code coupled with wave number-frequency spectra for the various flow regimes to calculate the side window vibration from which the sound pressure level spectrum at the driver's ear is determined. These predictions are compared to experimental wind tunnel data. The results demonstrate the ability of this methodology to correctly predict wind noise spectral trends as well as the overall loudness at the driver's ear. A more sophisticated simulation method employing the same lattice gas code is investigated for prediction of the time-accurate flow field necessary to compute the actual side glass pressure spectra.

A test cell was developed for evaluating a 6-speed automatic transmission. The target vehicle had an internal combustion 5.4L gasoline V8 engine. An electric dynamometer was used to closely simulate the engine characteristics. This included generating mean torque from the ECU engine map, with a transient capability of 10,000 rpm/second. Engine inertia was simulated with a transient capability of 20,000 rpm/second, and torque pulsation was simulated individually for each piston, with a transient capability of 50,000 rpm/second. Quantitative results are presented for the correlation between the engine driven and the dynamometer driven transmission performance over more than 60 test cycles. Concerns about using the virtual engine in validation testing are discussed, and related to the high frequency transient performance required from the electric dynamometer. Qualitative differences between the fueled engine and electric driven testing are presented.

A series of tests have been performed on a production vehicle to determine the characteristics of the external turbulent flow field in wind tunnel and road conditions. Empirical formulas are developed to use the measured data as source levels for a Statistical Energy Analysis (SEA) model of the vehicle structural and acoustical responses. Exterior turbulent flow and acoustical subsystems are used to receive power from the source excitations. This allows for both the magnitudes and wavelengths of the exterior excitations to be taken into account - a necessary condition for consistently accurate results. Comparisons of measured and calculated interior sound levels show good correlation.

Sound package engineering has always been an art developed through experience and much subjective road testing. Because the problem is complex, it is essential to have a logical procedure to achieve the most efficient sound package. The quiet car concept is proposed as a solution. Additionally, a plea is made for relevant automobile-oriented material test procedures to be recognized industry-wide.

A time cost effective methodology has been developed for the prediction of the A-pillar vortex formation and the side and the rear window flow separation for the purpose of wind noise assessment. This methodology combines a simplified Computational Fluid Dynamics (CFD) model and wind tunnel test data by CFD post-processing tools. The solution of the simplified CFD model provides background data for the whole flow field, but it lacks detail features such as mirror, sealing groove and glass in-set, which are locally important but difficult to mesh and require a very fine mesh resolution. The wind tunnel test data was taken in the specific areas of interest at the A-pillar, side window, rear window area, and roof from a real automotive. Then the wind tunnel test data was superposed upon the simplified CFD model to correct the numerical error due to geometry simplification and insufficient mesh resolution.

Due to several indeterminate factors, the assessment of the durability performance of a vehicle body is traditionally accomplished using test methods. An analytical fatigue life prediction method (four-step durability process) that relies mainly on numerical techniques is described in this paper. The four steps comprising this process include the identification of high stress regions, recognizing the critical load types, determining the critical road events and calculation of fatigue life. In addition to utilizing a general purpose finite element analysis software for the application of the Inertia Relief technique and a previously developed fatigue analysis program, two customized programs have been developed to streamline the process into an integrated, user-friendly tool. The process is demonstrated using a full body, finite element model.

During frontal and rear end type collisions, very large forces will be imparted to the passenger compartment by the collapse of either front or rear structures. NCAP tests conducted by NHTSA involve, among other things, a door openability test after barrier impact. This means that the plastic/irreversible deformations of door openings should be kept to a minimum. Thus, the structural members constituting the door opening must operate during frontal and rear impact near the elastic limit of the material. Increasing the size of a structural member, provided the packaging considerations permit it, may prove to be counter productive, since it may lead to premature local buckling and possible collapse of the member. With the current trend towards lighter vehicles, recourse to heavier gages is also counterproductive and therefore a determination of an optimum compartment structure may require a number of design iterations. In this article, FEA is used to simulate front side door behavior.

Because it is common to attach plastic parts to other plastic, metal, or ceramic assemblies with mechanical fasteners that are often stronger and stiffer than the plastic with which they are mated, it is important to be able to predict the retention of the fastener in the polymeric component. The ability to predict this information allows engineers to more accurately estimate length of part service life. A study was initiated to understand the behavior of threaded fasteners in bosses molded from engineering thermoplastic resins. The study examined fastening dynamics during and after insertion of the fastener and the effects of friction on the subsequent performance of the resin. Tests were conducted at ambient temperatures over a range of torques and loads using several fixtures that were specially designed for the study. Materials evaluated include modified-polyphenylene ether (M-PPE), polyetherimide (PEI), polybutylene terephthalate (PBT), and polycarbonate (PC).

This paper compares the emissions performance of four ultra thin wall ceramic substrates with standard wall thickness product on a chassis dynamometer for two different substrate volumes. This comparison helps establish performance trends and provides useful information for selection of substrates in designing catalytic converter systems. This experimental study tests and compares four ultra thin wall products (400/4, 600/3, 600/4, and 900/2) with a standard wall product (400/6.5) at two different substrate volumes. Engine bench aging is used to simulate typical aged conditions. Temperature data as well as second by second and bag emissions data for hydrocarbons, carbon monoxide and oxides of nitrogen were used to evaluate the relative performances of the substrates. The US FTP and US06 driving cycles were used as protocols for the comparison. Results suggest that lower bulk density and higher geometric surface area interact to lead to lower emissions.

An experiment has been conducted to study the effect of vehicle alignment, tire construction and operational conditions on tire treadwear. The Taguchi approach was used to compose the experimental design and to analyze the data. The treadwear testing was conducted on the indoor test machine; this test duplicates the treadwear pattern observed during road test. The responses of interest were total wear, irregular wear patterns, and diagonal wear. The study quantified the relative importance of different factors to treadwear and also the degree of wear irregularity.

The development of a durable adhesive bonding technology for joining of aluminium automotive structures requires a full understanding of the importance of the environment on the chemistry of the adhesively bonded system. This paper describes the accelerated testing procedures used by Alcan to provide information on the significance of environmental factors on adherend surface, the bonding interface and adhesive and so establish the best combination of adhesive and surface pretreatment for good long term durability. The stress/humidity test provides information on adhesive and interface performance, while the neutral salt spray test illustrates durability and corrosion resistance of the pretreatment. Outdoor exposure testing provides the means of comparing the accelerated tests with real life durability.

The recycling and reclamation of metal-matrix composites (MMC's) are critical aspects of the commercialization process. By recycling, we mean the economic processing of MMC scrap for reuse as composite. Reclamation refers to the separation and recovery of the individual components of the composite, i.e., the various aluminum alloys and ceramic particles. Three forms of MMC wrought alloy scrap have been considered; i.e., D. C. (direct chill) cast log ends, extrusion butts, and cut extrusion scrap. Recycling each of these forms of scrap back into D. C. cast extrusion billet has been demonstrated. This has been accomplished by recycling the scrap back through the basic mixing process. Various ratios of scrap to virgin composite have been explored and optimum blends are being studied. Similarly, for MMC foundry alloy (high silicon) gates and risers produced in shape-casting, fluxing and degassing techniques have been developed so these may be recycled back into useful castings.

Splash and spray conditions created by tractor-trailer combinations operating on the Federal highway system have been studied and tested for many years with mixed results. Past events are reviewed briefly in this paper. In additional testing during 1983, using new state-of- the-art splash/spray suppressant devices, some encouragement was provided that these devices could work. The 1984 Motor Vehicle Manufacturers Association (MVMA) test program was designed to develop practicable and reliable test procedures to measure effectiveness of splash and spray reduction methods applied to tractor-trailer combination vehicles. Over 40 different combinations of splash/spray suppression devices on five different tractors and three van trailer types were tested. The spray-cloud densities for some 400 test runs were measured by laser transmissometers and also recorded by still photography, motion pictures, and videotape. On-site observers made subjective ratings of spray density.

An A356T61 cast aluminum lower suspension control arm has been put into production for the Lincoln Mark VIII. The mechanical requirements which drive the design for a critical part like this are discussed, together with some of the background knowledge needed to address the issues surrounding alloy and process selection. Particularly as it must be realized that the process impacts the degree to which the potential of the alloy can be realized. With this in mind, some of the research activities which have been spawned in parallel with the production activities are briefly covered. The sequence of events involved in the design and prototyping of the part itself are outlined, as is the implementation of a specialized low pressure casting line to produce the part. Part performance to date has been excellent and the quality controls and test methods which have been put in place to see that this remains so are also covered.

As the compliance with noise legislation became more difficult, Ford exhaust system development engineers increasingly encountered variances not only from vehicle-to-vehicle, but on the same vehicle tested in different locations. As a result, a series of tests were conducted to establish the correlation among various sites for vehicle exterior noise measurements. The purpose of this paper is to present the results and the method developed to achieve the correlation in terms of the following: 1. Ford and site equipment differences 2. Driver differences 3. Differences between site physical qualities Seven sites were evaluated in the program where seven vehicles were used with a good spread in exterior noise levels. A representative correlation plot is also presented which can be used to predict the expected noise level of any vehicle at any one of these test sites knowing the level obtained at the Ford site.

Gas carburized and quenched low alloy steels typically produce surface microstructures which contain martensite, retained austenite and often NMTP's (non-martensitic transformation products). The NMTP's are caused by a reduction of surface hardenability in the carburizing process from loss of alloying elements to oxidation. Gas carburized low alloy steels such as SAE 8620 with NMTP's on the surface have been shown to have inferior bending fatigue properties when compared to more highly alloyed steels which do not form NMTP's, such as SAE 4615M. One method of minimizing the formation of oxides and eliminating NMTP formation during carburizing and quenching is to use plasma carburizing instead of conventional gas carburizing. In this study the microstructures and bending fatigue performance of plasma carburized SAE 8620 and SAE 4615M is compared to the same alloys conventionally gas carburized and quenched.

This paper discusses a motor vehicle noise source identification technique designed for use during the SAE J986a or similar drive-by test procedure. It provides, by application of the Fourier Transform, the capability to obtain a narrowband (9.8 Hz) frequency resolution over an extended frequency range (0-10,000 Hz) at the peak vehicle noise level, a particular RPM, or a particular vehicle location in the test zone. Other features include corrections for the Doppler shift, averaging of noise tests, and subtraction of spectra of two separate noise tests from a component disconnect/reconnect procedure. The above analysis, in conjunction with the noise source isolation resulting directly from the disconnect procedure, identifies the major vehicle noise contributors in terms of their respective amplitudes and frequencies.

This paper describes the rapid development of the Ford GT transmission, from concept phase to production, where the technical challenges involved are implicit in the specifications provided. It presents the steps taken at a project management level to expedite development, as well as the tools used to design and rate components at the design stage. Examples of concurrent engineering are given as well as management techniques used to predict and address key risks. In addition, details of analysis and test procedures are given, underlining their contribution to the rapid introduction of the transmission to the market place.

A small-scale oxidation test for automatic transmission fluids has been developed. In the test air flow rates, temperature and catalytic activity can be closely controlled at desired levels. A test procedure for screening automatic transmission fluids is described. Data are presented illustrating the ability of the test to distinguish between different levels of oxidation resistance, the repeatability of the test, and the correlation achieved thus far with a presently used full-scale transmission oxidation test.

The SAE Recommended Practice J963 “Anthropomorphic Test Device for Dynamic Testing” describes a standard 50th percentile adult male anthropomorphic test dummy. For nearly three years the Crash Test Dummy Task Force worked with the limited data available in selecting values for the body dimensions and ranges of motion. The data for specifying the values of mass distribution were developed experimentally as was a test procedure for determining the dynamic spring rate of the thorax.