Search Results

Ford Motor Company is participating in the Department of Energy's (DOE) Ultra-Clean Transportation Fuels Program with the goal to explore the development of innovative emission control systems for advanced compression-ignition direct-injection (CIDI) transportation engines. CIDI (or diesel) engines have the advantages of a potential 40% fuel economy improvement and 20% less CO2 emissions than current gasoline counterparts. To support this goal, Ford plans to demonstrate an exhaust emission control system that provides high efficiency particulate matter (PM) and NOx reduction. Very low sulfur diesel fuel will be used to enable low PM emissions, reduce the fuel economy penalty associated with the emission control system, and increase the long-term durability of the system. The end result will allow vehicles with CIDI engines to be Tier II emissions certified at a minimum cost to the consumer.

The effects of port fuel injection (PFI) timing and targeting on air/fuel (A/F) control, exhaust emissions, and combustion stability at retarded spark timing were investigated on a 2.0L I-4 engine with production injectors (300-350 micron SMD droplet spray). Timings were fully closed valve injection (CVI) or fully open valve injection (OVI), and selected targetings were towards the valve or port floor. An “ideal” pre-vaporized, pre-mixed fuel system was also tested to provide a baseline with which to isolate PFI fuel preparation effects. The key findings were: Transient A/F excursions with PFI were minimized over the full temperature range with OVI timing and valve targeting. The X-tau modeled film mass for OVI/valve target was 50% less than CVI/valve target and 30% less than OVI/port target with a cold engine (20° C). When fully warm (90° C), the A/F response of CVI/valve target improved to near that of OVI.

This study was performed to quantify the effects of injector targeting and fuel volatility on transient A/F excursions and fuel film mass in a port fuel injected (PFI) engine. Two injector targeting positions as well as injection timing and four different fuels were studied. Warm-up tests were performed with the throttle ramped between two positions over a one second interval to provide smooth changes in airflow and injected fuel. The exhaust A/F was recorded for each transient and fit using the X-τ model to estimate the change in the liquid fuel stored in the port and cylinder due to the throttle ramp. The change in fuel stored in the films was: ∼20% less with valve targeting ∼30% less with IVO injection timing 50-100% higher for hesitation fuel

The 1-2 shift characteristics of a 4-speed automatic transmission are examined. Shift quality fundamentals and ratio change mechanics are discussed, and shift quality metrics are introduced. A simple model is developed to describe the shift characteristics. Powertrain dynamometer data illustrate the effects of throttle position, band-brake capacity, spark timing, and transmission fluid temperature. Band-brake apply pressure largely determines the inertia phase output shaft torque. Retarded spark timing permits substantial reduction of vibration dose value at constant shift duration. Due to increased viscous torque from the drum interface oil film, band capacity significantly increases during the first 0.1-0.2 s of the inertia phase for temperatures less than 40 C.

Spark retard is desirable for decreasing cold start hydrocarbon emissions and lighting off the catalyst more rapidly. The focus of this work is to better understand the nature of the HC emissions as spark is retarded and investigate the location of the oxidation (in-cylinder or in the exhaust port and manifold). Fast FID measurements were taken in the exhaust port of a single cylinder research engine during cold, retarded spark engine operation (1200 rpm, 2.5 bar IMEP, 20 °C fluids). At moderate spark retard both Fast FID (exhaust port) and exhaust plenum HC levels decreased due to reduced crevice volume fraction at the end of burn, and increased in-cylinder burn up. In contrast, at large spark retard the port HC's increased dramatically while the exhaust plenum levels continued to fall to near zero. This is thought to be due to the onset of incomplete in-cylinder combustion along with increased exhaust port and manifold after-burning caused by the increasing exhaust gas temperatures.

Engine operation with spark ignition retarded from MBT timing is used at cold start to reduce HC emissions and increase exhaust gas temperature; however it also results in increased cyclic variations. Steady-state cold fluids testing was performed to better understand the causes of the cycle-to-cycle variations. Detailed analysis of individual cycles was performed to help gain an understanding of the causes of cyclic variations. The important results were: The primary cause of cyclic variations in IMEP is variations in the combustion phasing (location of 50% mass fraction burned). The expansion ratio decreases rapidly during combustion for retarded spark timing and therefore the phasing determines individual cycle thermal efficiency and IMEP. Variations in the late burn have little impact on the IMEP as this combustion occurs close to EVO and does little expansion work.

In order to experience harmony among the various perceptual cues experienced by an automobile customer, the acoustic environment must be considered. Acoustic events generated by automotive systems can have a dramatic effect on a customer's impression of vehicle quality and reliability. Additionally, certain vehicle segments are partially defined by the vehicle's sound characteristic. For example, luxury segments are defined by quiet and smooth powertrain sound, whereas some sports car segments are defined by loud and rough powertrain sound. This paper is a discussion of the impact automotive acoustic events can have on the customer. Addressed will be the methods typically used in both data collection and subsequent jury evaluations. Two case studies will be discussed. Finally, there will be a brief discussion on the future role of psychoacoustics in the vehicle environment.

Thermally-sprayed, composite coatings have been developed and sprayed on aluminum engine heads to replace powdered metal valve seat inserts. The process uses a conventional two-wire arc (TWA) gun with nickel and iron-based wire feedstocks. A unique surface preparation technique was developed to assure excellent coating adhesion. A composite Fe/Fe3O4/Ni/NiO/CrO coating was dynamometer tested using a single-cylinder Rotax engine, and showed improved wear performance over a conventional powdered-metal insert. Details of surface preparation, coating development, tribological properties and engine testing are described in this work.

Nonthermal plasma discharges in combination with catalysts are being developed for diesel aftertreatment. NOx conversion has been shown over several different catalyst materials. Particulate removal has also been demonstrated. The gas phase chemistry of the plasma discharge is described. The plasma is oxidative. NO is converted to NO2, CH3ONO2 and HNO3. Hydrocarbons are partially oxidized resulting in aldehydes and CO along with various organic species. Soot will oxidize if it is held in the plasma. When HC is present, SO2 is not converted to sulfates. Suitable plasma-catalysts can achieve NOx conversion over 70%, with a wider effective temperature range than non-plasma catalysts. NOx conversion requires HC and O2. Electrical power consumption and required exhaust HC levels increase fuel consumption by several percent. A plasma catalyst system has demonstrated over 90% particulate removal in vehicle exhaust.

This paper summarizes the first phase of an experimental effort focused on developing a comprehensive understanding of the in-cylinder air/fuel mixing and combustion processes in spark-ignition engines using laser-based fuel distribution and combustion measurements. As part of this first phase, a semi-quantitative, laser-induced fluorescence, fuel distribution measurement technique was developed and demonstrated. The calibration, correction, and image analysis processes associated with the technique were shown to be comparatively simple and effective (relative to other analytical and empirical methods). The error associated with the technique was shown to be 5 - 10 % under vapor phase conditions. This work was applied to a port fuel injected optical engine, which was designed for optical access through the piston and cylinder liner under firing conditions.

In-cylinder pressure traces vary significantly from cycle-to-cycle in spark-ignition (SI) engines. The variations, substantially present even when engine is stable, are magnified under certain engine operating conditions. As a result, engine torque output oscillates and engine operation becomes unstable. EGR tolerance, lean burn limit and spark retard capabilities at CSSRE (Cold Start Spark Retard and Enleanment) are mostly determined by the levels of cycle-to-cycle variations. None of the engine computer models, however, have included cyclic variations for routine industrial applications. As the application domain of engine simulation models expands into unstable engine operating conditions, the modeling of cyclic variations becomes increasingly important. In this research, reviews were conducted regarding different approaches for the simulation of cyclic variation.

Environmental concerns have prompted increasingly stringent government legislation regulating automotive fuel economy and emissions. Recent rules not only mandate lower total emissions, but also require on-board diagnostics which monitor the vehicle exhaust systems. In order to satisfy these requirements, new and improved exhaust gas sensors are continually being developed to serve as part of the engine feedback control and emissions monitoring systems. Before we can properly design these new sensors, we must attempt to better understand the harsh environment in which they will operate. In this paper, we examine the high frequency nature of pressure fluctuations found in the exhaust system for both steady state and transient engine operating conditions. We also investigate temperature fluctuations, but restrict these measurements to the sampling environment found in the packaging of a Ford Si-based microcalorimeter.

A planar dielectric barrier discharge device has been tested for exhaust emission reduction in simulated engine exhaust. This device's electrical characteristics have been measured and are presented in this paper. The device consists of two dielectric barriers which act like series capacitors, with the gas gap between them. At low gap voltages, the gas gap also acts like a capacitance, with a much smaller capacitance than the barriers. At higher voltages, the gas gap breaks down and a blue–purple glow visually fills the gap. The partially ionized gas conducts charge across the gap, building electrical charge on the dielectric barrier inner surface. When the AC excitation voltage peaks and starts to go toward an opposite polarity, the discharge momentarily extinguishes, trapping charge in the dielectric barrier capacitance.

The requirement of reducing HC emissions during cold start and improving transient performance has prompted a study of the fuel injection process. Port-fuel-injection with the Intake-valve open using small droplets is a potentially feasible option to achieve the goals. To gain a better understanding of the injection process, the effects of droplet size, injection timing, and coolant temperature on the total and speciated HC emissions were tested In a Single-cylinder engine. It was found that droplet size plays an important role in the total HC emission increase during open-valve injection, especially with cold operation. Large droplets (300 μm SMD) produced a substantial HC increase while small droplets (14 μm SMD) produced no observable increase. Increase In the total HC emissions was always accompanied by an increase in the heavy fuel components in the exhaust gases.

A diesel fuel and air diffusion flame burner system has been designed for laboratory simulation of diesel exhaust gas. The system consists of mass flow controllers and a fuel pump, and employs several unique design and construction features. It produces particulate emissions with size, number distribution, and morphology similar to diesel exhaust. At the same time, it generates NOx emissions and HC similar to diesel. The system has been applied to test plasma discharges. Different design discharge devices have been tested, with results indicating the importance of testing devices with soot and moisture. Both packed bed reactor and flat plate dielectric barrier discharge systems remove some soot from the gas, but the designs tested are susceptible to soot fouling and related electrical failures. The burner is simple and stable, and is suitable for development and aging of plasma and catalysts systems in the laboratory environment.

In 1999, the first generation NOx sensor from NGK Spark Plug, Co., Ltd. was commercialized for use in gasoline LNT NOx after-treatment systems [ 1 ]. Since then, as emissions regulations and OBD requirements have become more stringent, the demand for a high-accuracy NOx sensor with fast light-off has increased, particularly for diesel after-treatment systems. To meet such market demands, NGK Spark Plug, Co., Ltd. has developed, in collaboration with Ford Motor Company, a second generation NOx sensor.

This paper describes the reduction of cyclic combustion variations in spark-ignited engines, especially under idle conditions in which the air-fuel mixture is lean of stoichiometry. Under such conditions, the combination of residual cylinder gas and parametric variations (such as variations in fuel preparation) gives rise to significant combustion instabilities that may lead to customer-perceived engine roughness and transient emissions spikes. Such combustion instabilities may preclude operation at air-fuel ratios that would otherwise be advantageous for fuel economy and emissions. This approach exploits the recognition that a component of the observed combustion instability results from a noise-driven, nonlinear deterministic mechanism that can be actively stabilized by small feedback control actions which result in little if any additional use of fuel.

Projected NOx and fuel costs are compared for a plasma-catalyst system and an active lean NOx catalyst system. Comparisons are based on modeling of FTP cycle performance. The model uses steady state laboratory device characteristics, combined with measured vehicle exhaust data to predict NOx conversion efficiency and fuel economy penalties. The plasma system uses a proprietary catalyst downstream of a plasma discharge. The active lean NOx catalyst uses a catalyst along with addition of hydrocarbons to the exhaust. For the plasma catalyst system, NOx conversion is available over a wide temperature range. Increased electrical power improves conversion but degrades vehicle fuel economy; 10 J/L energy deposition costs roughly 3% fuel economy. Improved efficiency is also available with larger catalyst size or increased exhaust hydrocarbon content. For the active lean NOx system, NOx conversion is available only in a narrow temperature range.

The direct injection gasoline spray-wall interaction was characterized inside a heated pressurized chamber using various visualization techniques, including high-speed laser-sheet macroscopic and microscopic movies up to 25,000 frames per second, shadowgraph, and doublespark particle image velocimetry. Two hollow cone high-pressure swirl injectors having different cone angles were used to inject gasoline onto a heated plate at two different impingement angles. Based on the visualization results, the overall transient spray impingement structure, fuel film formation, and preliminary droplet size and velocity were analyzed. The results show that upward spray vortex inside the spray is more obvious at elevated temperature condition, particularly for the wide-cone-angle injector, due to the vaporization of small droplets and decreased air density. Film build-up on the surface is clearly observed at both ambient and elevated temperature, especially for narrow cone spray.

Diesel vehicles have significant advantages over their gasoline counterparts including a more efficient engine, higher fuel economy, and lower emissions of HC, CO, and CO2. However, NOx control is more difficult on a diesel because of the high O2 concentration in the exhaust, making conventional three-way catalysts ineffective. The most promising technology for continuous NOx reduction onboard diesel vehicles is Selective Catalytic Reduction (SCR) using aqueous urea. Recent work with urea SCR has involved aftertreatment for the 1.2L DIATA common-rail diesel engine. This engine was used in Ford's hybrid-electric vehicle, the Prodigy, which was developed under the PNGV (Partnership for a New Generation of Vehicles) program. An emission control system consisting of a diesel particulate filter followed by an underbody SCR system was used successfully to meet ULEV emission standards (0.2 g/mi NOx, 0.04 g/mi particulate matter (PM)).