Search Results

The thermal durability of a large frontal area cordierite ceramic wall-flow filter for light-duty diesel engine is examined under various regeneration conditions. The radial temperature distribution during burner regeneration, obtained by eight different thermocouples at six different axial sections of a 75″ diameter x 8″ long filter, is used together with physical properties of the filter to compute thermal stresses via finite element analysis. The stress-time history of the filter is then compared with the strength and fatigue characteristics of extruded cordierite ceramic monolith. The successful performance of the filter over as many as 1000 regenerations is attributed to three important design parameters, namely unique filter properties, controlled regeneration conditions, and optimum packaging design. The latter induces significant radial and axial compression in the filter thereby enhancing its strength and reducing the operating stresses.

Finite element methods can be used to simulate a class of variation problems induced by build distortion in the assembly process. The FEM approach was used to study two representative assembly problems: 1) Front fender mounting and resulting distortion due to various fastening sequences; and, 2) Coupe door assembly process and resulting deformation due to clamping and welding of flexible sheet metal parts. FEM is used to generate sensitivities of various process conditions. Correlation with measured Co-ordinate Measuring Machine (CMM) data is shown. The use of FEM to simulate manufacturing/assembly processes in the automotive industry is in it's infancy. As the new methods are developed this capability can be used to study the assembly process and provide guidance in designing more robust parts and assembly processes.

The dilemma of using a shoulder belt force limiter with a 3-point belt system is selecting a limit load that will balance the reduced risk of significant thoracic injury due to the shoulder belt loading of the chest against the increased risk of significant head injury due to the greater upper torso motion allowed by the shoulder belt load limiter. However, with the use of air bags, this dilemma is more manageable since it only occurs for non-deploy accidents where the risk of significant head injury is low even for the unbelted occupant. A study was done using a validated occupant dynamics model of the Hybrid III dummy to investigate the effects that a prescribed set of shoulder belt force limits had on head and thoracic responses for 48 and 56 km/h barrier simulations with driver air bag deployment and for threshold crash severity simulations with no air bag deployment.

This paper describes the design, synthesis-analysis and development of the unique vehicle structure architecture for the fifth generation Chevrolet Corvette, ‘C5’, which starts in the 1997 model year. The innovative structural layout of the ‘C5’ enables torsional rigidity in an open roof vehicle which exceeds that of all current production open roof vehicles by a wide margin. The first structural mode of the ‘C5’ in open roof configuration approaches typical values measured in similar size fixed roof vehicles. Extensive use of CAE and a systems methodology of benchmarking and requirements rolldown were employed to develop the ‘C5’ vehicle architecture. Simple computer models coupled with numerical optimization were used early in the design process to evaluate every design concept and alternative iteration for mass and structural efficiency.

A design synthesis approach is used to design and analyze a Resin-Transfer-Molded (RTM) composite floorpan to meet the product requirements and assess the structural performance. The design envelope is based on packaging constraints representative of a production vehicle to ensure a feasible design intent. Finite element analysis of the composite design is used to guide the design and integrate all of the product performance requirements to achieve a feasible design concept. Issues discussed include the design and analysis, design features, composite material tailoring, prototype fabrication, vehicle build, and product validation. Stiffness, strength and durability tests were performed on the floorpan and the fully trimmed vehicle, and all requirements were met.

The Hybrid III dummy is an anthropomorphic (humanlike) test device, generally used in crashworthiness testing to assess the extent of occupant protection provided by the vehicle structure and its restraint systems in the event of vehicle crash. Lumped-parameter analytical models are commonly used to simulate the dummy response. These models, by virtue of their limited number of degrees of freedom, can neither represent accurate three-dimensional dummy geometry nor detailed structural deformations. In an effort to improve the state-of-the-art in analytical dummy simulations, a set of finite element models of the Hybrid III dummy segments - head, neck, thorax, spine, pelvis, knee, upper extremities and lower extremities - were developed. The component models replicated the hardware geometry as closely as possible. Appropriate elastic material models were selected for the dummy “skeleton”, with the exterior “soft tissues” represented by viscoelastic materials.

This paper describes an analytical method to predict the sensor closure time for an airbag (Supplemental Inflatable Restraint - SIR) system in frontal impacts. The analytical tools used are the explicit finite element code, an in-house sensor closure time prediction program, and a full vehicle finite element model. Nodal point information obtained from the full vehicle finite element simulation is used to predict the sensor closure time of the airbag system. This analytical method can provide the important crash signature information for a SIR system development of a new vehicle program. In this paper, 0-degree frontal impacts at four different impact speeds with two different bumper energy absorption systems are studied using the non-linear finite element computer program DYNA3D. It is concluded that this analytical method is very useful to predict the SIR sensor closure time.

Although rollover crashes represent a small fraction (approximately 3%) of all motor vehicle crashes, they account for roughly one quarter of crash fatalities to occupants of cars, light trucks, and vans (NHTSA Traffic Safety Facts, 2004). Therefore, the National Highway Traffic Safety Administration (NHTSA) has identified rollover injuries as one of its safety priorities. Motor vehicle manufacturers are developing technologies to reduce the risk of injury associated with rollover collisions. This paper describes the development by General Motors Corporation (GM) of a suite of laboratory tests that can be used to develop sensors that can deploy occupant protection devices like roof rail side air bags and pretensioners in a rollover as well as a discussion of the challenges of conducting this suite of tests.

A rear full overlap car-to-car high speed impact simulation using the DYNA3D Finite Element Software was performed to examine the crush mode for rear structure of a vehicle and to observe the effect of rear bumper system in order to maintain the fuel system integrity. The study was conducted first for two different bumper system configurations, namely: (1) validating the model for struck vehicle with steel rear bumper system, (2) simulating rear end collision with composite rear bumper system attached to the rear rails of struck vehicle. Later a third simulation of the model was conducted with a viable design modification to the composite bumper system for improved crashworthiness. It was identified that a more comprehensive FEA model of the bullet car including front end structure, powertrain components, cooling system and other components which constitute the load paths should be incorporated in the analysis to obtain more meaningful correlation and crashworthiness prediction.

As the need for plastic components with high-performance and low systems cost continues to escalate, the issues associated with bringing applications to automotive market have become more complex. Automotive applications such as seamless integral Passive Supplemental Inflatable Restraint (PSIR) systems can have tearseams that are either molded-in or laser scored. Molded-in tearseams in seamless Instrument Panels (IP) eliminate the secondary operation of laser scoring, but they warrant thin wall molding conditions. This paper describes material characterization under thinwall molding conditions wherein the effects of processing on mechanical properties are explored. This paper also discusses results from a proprietary finite element code developed at GE to predict the processing parameters, which affect the mechanical properties of the material at the tearseam in a seamless IP system.

Automotive exterior paint systems can significantly affect the impact performance of thermoplastic body panels. To utilize the benefits of predictive engineering as a tool to assist in the design and development of thermoplastic body panels, thermoplastic body panel materials have been characterized with typical automotive paint systems for use for finite element modeling and analysis. Paint systems used for exterior body panels can vary from rigid to more flexible, depending on the vehicle manufacturer's specifications. Likewise, thermoplastics for body panels vary in mechanical properties, primarily depending on the heat performance requirements of the application. To understand the effects of paint systems on impact performance of thermoplastic body panels, two different paint systems, representing “rigid” and “more flexible,” were evaluated on two body panel grades of thermoplastics with different mechanical properties.

This paper presents an optimization technique for clamping forces determination in fixture design. First, the finite element analysis (FEA) is applied to determine the coefficients of compliant matrix of a fixture-workpiece system subjected to machining and clamping forces. Then, a nonlinear optimization model is constructed in terms of the FEA results and mechanical and geometrical constraints. The optimization model is derived to determine the feasible clamps under the corresponding force effects. The optimal magnitude and direction of clamping forces minimize the workpiece deformation at particular key points. Finally, a scaled engine block with the 3-2-1 fixturing principle is given as an example.

This paper describes a numerical simulation technique applicable to the FMVSS 214 side impact test through the use of the finite element method (FEM) technology. The paper outlines the development of the side impact dummy (SID), moving deformable barrier (MDB) and the test vehicle FEM models, as well as the development of new advanced constitutive models of materials and algorithms in LS-DYNA3D which are related to the topic. Presented in the paper are some initial simulation problems which were encountered and solved, as well as the correlation of the simulation data to the physical test.

Automotive interiors are undergoing rapid transformation with the introduction of invisible PSIR integral systems. This styling trend requires continuous class A surface for the Instrument Panel (IP) and introduces complexities in the design and analysis of PSIR integral systems. The most important criterion for airbag doors is that it must open as intended, at the tearseam, within the deployment temperature range and without fragmentation. Consequently it is imperative that in analytical simulations, the finite element model of the tearseam is accurate. The accuracy of the model is governed by (a) optimal level of refinement, (b) surface geometry representation and (c) material model. This paper discusses modeling methodology for tearseams with respect to mesh refinement and the effect of geometry.

This paper discusses a Design for Six Sigma (DFSS) based methodology for designing an injection molded bumper energy absorber to help meet vehicle pedestrian protection requirements. The development process is described, and an example is presented of its use in designing an injection molded energy absorber for a range of various vehicle styling parameters. First, an idealized set-up incorporating the car styling parameters critical for pedestrian protection requirements was developed. Then, the vehicle and Energy Absorber (EA) geometries were parameterized and a DFSS process was employed to investigate the design space using Finite Element Impact Analysis with a commercially available Lower Leg Form Impactor.

Federal legislation for head impact protection in upper automotive interiors (FMVSS 201U) has presented a unique energy management problem for the automotive industry. Due to extremely tight packaging conditions, energy absorbers are required to have efficiencies which exceed those of traditional foam materials, and force the development of new methods of energy absorption. The push toward shortened design cycle times has required the use of predictive engineering tools such as finite element analysis. Predictive tools which can accurately drive design direction reduce design cycle times, costs associated with multiple prototype part builds, and costs associated with physical testing. Over the last few years, the inclusion of FMVSS 201U energy absorbing countermeasures in the upper interior trim has been largely experimental in nature, yielding solutions which are costly in both time and money.

As a result of the increased reliance on predictive engineering to reduce vehicle development resources, increasingly accurate predictive finite element models are important to help engineers meet cost and timing restrictions. For components made of engineering thermoplastics, accurate material modeling that helps predict part performance is essential. This material modeling accuracy is even more important where high speed and high loading conditions exist such as in airbag doors, knee bolsters and pillar trim. This paper addresses material modeling of engineering thermoplastics for finite element models that are subjected to high impact and high speed loading. Here, the basics of plastics behavior are introduced and a comparison of the accuracy of different material characterizations in an impact loading is presented. The material under analysis here is a polycarbonate - acrylonitrile butadiene styrene blend, PC-ABS.

The high costs of prototyping, revisions, and production tooling, with a higher emphasis on quality, concurrent with demands for miniaturization, higher-density packaging, stricter performance, and a shortened product development cycle, have led to the development of advanced analysis techniques that address the performance issues associated with failure prevention in automotive connectors. Because of the complex material and geometric nonlinearity demands in performance, traditional calculations are inadequate, and new methods, utilizing finite element analysis techniques were developed. These highly specialized analysis techniques will enable the designer and engineer to predict connector performance with a high degree of confidence. Concurrent with concept designs, structural analyses (in the areas of assembly, disassembly, and terminal retention) must be done prior to design release.

Finite element analysis (FEA) predictions of magnesium beams are compared to load versus displacement test measurements. The beams are made from AM60B die castings, AM30 extrusions and AZ31 sheet. The sheet and die cast beams are built up from two top hat sections joined with toughened epoxy adhesive and structural rivets. LS-DYNA material model MAT_124 predicts the magnesium behavior over a range of strain rates and accommodates different responses in tension and compression. Material test results and FEA experience set the strain to failure limits in the FEA predictions. The boundary conditions in the FEA models closely mimic the loading and constraint conditions in the component testing. Results from quasi-static four-point bend, quasi-static axial compression and high-speed axial compression tests of magnesium beams show the beam's behavior over a range of loadings and test rates. The magnesium beams exhibit significant material cracking and splitting in all the tests.

Aspirating airbag modules are unique from other designs in that the gas entering the airbag is a mixture of inflator-delivered gas and ambient-temperature air entrained from the atmosphere surrounding the module. Today's sophisticated computer simulations of an airbag deployment typically require as input the mass-flow rate, chemical composition and thermal history of the gas exiting the canister and entering the airbag. While the mass-flow rate and temperature of the inflator-delivered gas can be obtained from a standard tank test, information on air entrainment into an aspirated canister is limited. The purpose of this study is to provide quantitative information about the aspirated mass-flow rate during airbag deployment. Pressure and velocity measurements are combined with high-speed photography in order to gain further insight into the relationship between the canister pressure, the rate of cabin-air entrainment and the airbag deployment.