Search Results

Damping treatments are widely used in passenger vehicles, but the knowledge of damping treatments is often fragmentary in the industry. In this study, vibro-acoustics behavior of a set of vehicle floor and dash panels with various types of damping treatments was investigated. Sound transmission loss, sound radiation efficiency as well as damping loss factor were measured. The damping treatments ranged from laminated steel construction (thin viscoelastic layer) and doubler plate construction (thick viscoelastic layer) to less structural “bake-on” damping and self-adhesive aluminum foil-backed damping treatments. In addition, the bare vehicle panels were tested as a baseline and the fully carpeted floor panel was tested as a reference. The test data were then examined together with analytical modeling of some of the test configurations. As expected, the study found that damping treatments add more than damping. They also add mass and change body panel stiffness.

This paper discusses a study conducted by GM to better understand the factors that influence injury potential in vehicle-to-vehicle side impacts. A number of other studies have been done which focus primarily on frontal vehicle-to-vehicle compatibility. GM focused on side impact compatibility in this study due to the risk of harm generally associated with this type of crash. Real world field performance was studied through an extensive six-state field analysis of recent model year (‘94+) vehicles. Of particular interest in this study was an efficacy analysis of the MVSS 214 dynamic side impact standard, which was phased-in starting with some 1994 model year passenger cars. Physical side impact crash testing of a 1997 passenger car was used to investigate the relationship of impacting mass, speed, geometric profile and stiffness on side impact intrusion and occupant injury.

Crash-test-data on local longitudinal and shear stiffness of the vehicle front is needed to estimate impact severity from car deformation in offset or pole impacts, and to predict vehicle acceleration and compartment intrusion in car-to-car crashes. Repeated full frontal crash-tests were carried out with a load-cell barrier to determine the local longitudinal stiffness with increasing crush. Repeated off-set tests were run to determine shear stiffness. Two single high-speed tests (full frontal and offset) were carried out and compared to the repeated tests to determine the rate sensitivity of the front structure. Four repetitions at 33.4 km/h provided equivalent energy absorption to a single 66.7 km/h test, when rebound was considered. Power-train inertial effects were estimated from highspeed tests with and without power-train. Speed effects averaged 2% per [m/s] for crush up to power-train impact, and post-crash measurements were a reasonable estimate of front-structure stiffness.

Injury risk curves for SID-IIs thorax and abdomen rib deflections proposed for future NCAP side impact evaluations were developed from tests conducted with the SID-IIs FRG. Since the floating rib guide is known to reduce the magnitude of the peak rib deflections, injury risk curves developed from SID-IIs FRG data are not appropriate for use with SID-IIs build level D. PMHS injury data from three series of sled tests and one series of whole-body drop tests are paired with thoracic rib deflections from equivalent tests with SID-IIs build level D. Where possible, the rib deflections of SID-IIs build level D were scaled to adjust for differences in impact velocity between the PMHS and SID-IIs tests. Injury risk curves developed by the Mertz-Weber modified median rank method are presented and compared to risk curves developed by other parametric and non-parametric methods.

Neck injury assessment is part of the FMVSS208 requirements. Hardware tests are often conducted to validate whether the vehicle safety system meets the requirements. This paper presents a full vehicle finite element model using LS-DYNA, including structural components, restraint system components, and dummies. In the case of a frontal impact at 30deg angle, in the areas of neck compression, neck extension and neck kinematics, it is demonstrated that a good correlation is achieved between the response of a FE dummy in the model and those of ATDs in the physical hardware tests. It is concluded that the math tool may be applied to comprehend test and design variations that may arise throughout a vehicle development lifecycle and to help develop a vehicle restraint system.

The concept of height of force has been suggested by some researchers as one possible parameter defining the structural interaction probability between vehicles of different sizes. This proposed parameter was defined as the vertical centroid of forces exerted on a flat barrier surface when a vehicle crashes into the barrier. It is therefore measured as a function of elapsed time since crash. In this paper, the height of force is obtained from theoretical calculations and also measured in crash tests at 56 km/h against barriers instrumented with an array of load cells. It is observed that the measured values of height of force have significant errors which are dependent on factors other than the crash conditions and the properties of the vehicle's structure and geometry. These factors need to be taken into account in future discussions of using the height of force or the average height of force as an indicator of vehicle compatibility.

The auto industry has had decades of experience with designing safe vehicles. The introduction of highly integrated features brings new challenges that require innovative adaptations of existing safety methodologies and perhaps even some completely new concepts. In this paper, we describe some of the new challenges that will be faced by all OEMs and suppliers. We also describe a set of generic top-level potential hazards that can be used as a starting point for the Preliminary Hazard Analysis (PHA) of a vehicle software-intensive motion control system. Based on our experience with the safety analysis of a system of this kind, we describe some general categories of hazard causes that are considered for software-intensive systems and can be used systematically in developing the PHA.

Eight lateral dolly rollover tests were conducted on 1983 Chevrolet Malibusata nominal speed of 51.5 km/h (32 mi/h). Four of the vehicles had rollcages, and four had standard production roofs. Unrestrained outboard front GM Hybrid ill dummies with head and neck transducers were used. Numerous cameras documented the vehicle and dummy movements. Detailed vehicle kinematics data allowed quantitative analysis of the conditions for head and neck loads. For both roof structures, the dummies moved upward and outward from their seats due to rotation and acceleration of the vehicle. High head/neck loads were measured when the head contacted a part of the car experiencing a large change in velocity, often that part of the car which struck the ground. The results of this work indicate that roof strength is not an important factor in the mechanics of head/neck injuries in rollover collisions for unrestrained occupants.

Forming of sheet metal structures induces pre-strains, thickness variations, and residual stresses. Pre-strains in the formed structures introduce work hardening effects and change material fatigue properties such as stress-life or strain-life. In the past, crashworthiness and durability analyses have been carried out using uniform sheet thickness and stress- and strain-free initial conditions. In this paper, crashworthiness and durability analyses of hydroformed front rails, stamped engine rails and shock towers on a full vehicle and a Body-In-White structure are performed considering the residual forming effects. The forming effects on the crash performance and fatigue life are evaluated.

This paper examines the effect that test barriers currently used for frontal and side impact tests have had on collision compatibility between different-sized vehicles. The peak force levels generated by the vehicles’ front structures are one of the significant factors in determining vehicle compatibility. It is shown from principles of mechanics that the use of fixed barriers as a test device may lead to higher force levels for front ends of larger vehicles and thus increase the incompatibility between large and small vehicles. Review of data from various sources supports this conclusion that the peak force levels of vehicles’ front ends have increased in proportion to their test mass. Available crash data is also examined for a relationship between NCAP ratings of vehicles and the likelihood of serious and fatal injuries to occupants of those vehicles. These data do not show any relationship between the frontal NCAP ratings of vehicles and their rate of serious or fatal injuries.

The efficiency of several Microstrip (Patch) antennas with varying substrate heights etched on a substrate material with a relatively high dielectric constant was calculated from gain measurement data. The radiation efficiency of a 4, 5, 6 and 7mm thick patches were measured to be 0.8887, 0.9097, 0.9163 and 0.9202, respectively. The efficiency of a λ/4 monopole at the same frequency was measured to be 0.9389. To achieve a -2.0 dBi of gain at an elevation angle θ = 90° and a +2 dBic at elevation angles between 30° and 70° for the XM signal reception, the patch efficiency has to exceed the efficiency of a λ/4 monopole at the same frequency.

As the automotive industry becomes more concerned with the crash performance of automobiles, the behavior of used vehicles becomes an interesting subject. In this work, the effect of aging on spot welded joints was simulated by applying fatigue loading to the samples. Samples were then subjected to quasi-static and impact tests to measure the effect of fatigue aging to the strength of the samples. The results show (a) a reduction in the strength of the test samples under impact conditions, (b) no obvious reduction in quasi-static conditions, and (c) significant reduction in strength if cracks in the welds were initiated during the fatigue aging process.

This paper examines the effect of rate dependence of material parameters on FMVSS 201 simulation using LS-DYNA with the exiting elasto-plastic material models and user subroutines. The material parameters investigated include the yield stress, Young's modulus and failure strain. The effect of yield criterion is also discussed.

The National Fire Protection Association (NFPA) publishes NFPA 921, “Guide for Fire and Explosion Investigations” (1) on generally a three to four year cycle. This guide includes a chapter on the investigation of motor vehicle fires. For the new 2008 edition of this publication the SAE and the NFPA worked closely together in the revision of this chapter. This paper provides a broad overview of the revised chapter and summarizes the major revisions. By using SAE participation in the chapter revision, engineers familiar with or even directly involved in the design of the vehicle systems discussed, helped to develop many of the system descriptions included in the revised chapter. The revised Motor Vehicle chapter like the parent document is both a consensus document and an effective guide which provides origin and cause analysis of motor vehicle fires, an investigative process consistent with principles stated throughout NFPA 921 and adherence to scientific methods.

The development of the WorldSID 50th percentile male dummy was initiated in 1997 by the International Organization for Standardization (ISO/SC12/TC22/WG5) with the objective of developing a more biofidelic side impact dummy and supporting the adoption of a harmonized dummy into regulations. More than 45 organizations from all around the world have contributed to this effort including governmental agencies, research institutes, car manufacturers and dummy manufacturers. The first production version of the WorldSID 50th male dummy was released in March 2004 and demonstrated an improved biofidelity over existing side impact dummies. Full-scale vehicle tests covering a wide range of side impact test procedures were performed worldwide with the WorldSID dummy. However, the vehicle safety performance could not be assessed due to lack of injury risk curves for this dummy. The development of these curves was initiated in 2004 within the framework of ISO/SC12/TC22/WG6 (Injury criteria).

The Experimental Safety Vehicle powertrain and fuel system developed by General Motors in compliance with Contract DOT-OS-00095 with the U.S. Department of Transportation include several special features: a low engine accessory package to meet the front visibility down angle of 8 degrees, engine and transmission mounting for retention at high decelerations, a light aluminum engine, an over-the-rear-axle fuel tank, and a unique evaporative emission fuel pipe routing. A comprehensive test program was planned and final testing to validate contract specifications was conducted.

Forward collision warning (FCW) systems are intended to provide drivers with crash alerts to help them avoid or mitigate rear-end crashes. To facilitate successful deployment of FCW systems, the Ford-GM Crash Avoidance Metrics Partnership (CAMP) developed preliminary minimum functional requirements for FCW systems implemented on light vehicles (passenger cars, light trucks, and vans). This paper summarizes one aspect of the CAMP results: minimum requirements and recommendations for when to present rear-end crash alerts to the driver. These requirements are valid over a set of kinematic conditions that are described, and assume successful tracking and identification of a legitimate crash threat. The results are based on extensive closed-course human factors testing that studied drivers' last-second braking preferences and capabilities. The paper reviews the human factors testing, modeling of results, and the computation of FCW crash alert timing requirements and recommendations.

Different countermeasure designs for reducing the HIC (d) and to comply with FMVSS201U have been evaluated in many component-level studies by suppliers and OEMs. This study presents guidelines to support future countermeasure and interior designs. FMVSS201U has changed the way OEMs design interiors of the vehicles today. Most recently, much more work is being done to find ways to design interiors of the vehicles that comply with FMVSS201U while keeping the interiors aesthetically pleasing, attaining driver comfort and meeting driver visibility requirements. Introduction of side-rail airbags has further affected countermeasure design and packaging. This study focuses on several countermeasure designs in the side-rail region as used in a mid-sized vehicle implemented to meet FMVSS201U requirements and their efficiency with respect to Head Injury Criterion (HIC) reduction given a fixed packaging space.

A prototype fire suppression system was tested in one full-scale vehicle crash tests and three static vehicle fire tests. The prototype fire suppression system consisted of 2 Solid Propellant Gas Generators and two optical detectors. These components were installed on the hood of the test vehicle. A vehicle crash test and a series of static vehicle fire tests were performed to determine the effectiveness of this prototype fire suppression systems in extinguishing fires in the engine compartment of a crashed vehicle

A dual depth passenger air bag technology has been developed which provides two different deployed cushion shapes coupled with two inflation levels, but only uses two initiators, one for a single level inflator and one for a dual depth mechanism. The developed dual depth air bag module design utilizes a seat position switch to help determine deployed output. The module deploys a shallow cushion depth for occupants in the forward portion of seat track travel and a deep cushion depth for occupants in the rearward portion of seat track travel. The mechanism controls the release of an air bag cushion tether and also enables the inflator to vent a portion of gas through the module housing. This paper summarizes the development effort including initial sled and out-of-position testing. The final design was found to be a useful tool when balancing in-position restraint performance between otherwise competing in-position test conditions.