Search Results

A multi vector design tool to accurately predict instrument panel obscuration was developed to insure that critical legal displays in vehicles are not obscured. The concept provides for a computer generated light source shaped to replicate the human eyes. The light source is then projected onto a 3D math based arrangement and the resultant shadows are visible on the instrument panel surface and its displays. Design studios require criteria for the placement of the instrument cluster gages and displays, various controls, switches, and steering column stalks before an interior theme can be completed. Therefore, instrument panel obscuration and visibility must be determined early in the design process. The obscured areas are a function of the instrument panel surface, steering wheel rim, hub, spokes, and the location of the driver's eyes. This light source method allows engineers and designers the ability to quickly determine obscured areas.

The wear test introduced in this paper can be used to determine and rank PV (pressure time velocity) capability of plastic materials for applications where a plastic part is rotating or reciprocating against a metal surface. It provides an accelerated test method to evaluate the wear performance of plastic materials. A single test can provide tribological information at multiple PV conditions. The tribological information obtained from this method includes coefficient of friction, PV (pressure times velocity) limits, and interface temperature profile. This test is currently used by General Motors Corporation to develop plastic materials for transmission thrust washer and dynamic seal applications. The test is running in two sequences (A & B), capable of a PV range from 50,000 psi-ft/min 500,000 psi-ft/min, under dry conditions. The PV steps in sequence A are combinations of high pressure and low velocity - for applications where high loads are expected, such as thrust washers.

A common occurrence in computer aided design is the need to make changes to an existing CAD model to compensate for shape changes which occur during a manufacturing process. For instance, finite element analysis of die forming or die tryout results may indicate that a stamped panel springs back after the press line operation so that the final shape is different from nominal shape. Springback may be corrected by redesigning the die face so that the stamped panel springs back to the nominal shape. When done manually, this redesign process is often time consuming and expensive. This article presents a computer program, FESHAPE, that reshapes the CAD or finite element mesh models automatically. The method is based on the technique of volume morphing pioneered by Sederberg and Parry [Sederberg 1986] and refined in [Sarraga 2004]. Volume morphing reshapes regions of surfaces or meshes by reshaping volumes containing those regions.

As a virtual manufacturing press line, line die forming simulation provides a full range math-based engineering tool for stamping die developments of automotive structure and closure panels. Much beyond draw-die-only formability analysis that has been widely used in stamping simulation community during the last decade, the line die formability analysis allows incorporating more manufacturing requirements and resolving more potential failures before die construction and press tryout. Representing the most difficult level in formability analysis, conducting line die formability analysis of automotive body side outers exemplifies the greatest technological challenge to stamping CAE community. This paper discusses some critical issues in line die analysis of the body side outers, describes technical challenges in applications, and finally demonstrates the impact of line die forming simulation on the die development.

In the automotive industry, vehicle durability analysis is based on test schedule encompassing multiple road surfaces (events) including rough roads, potholes, etc. Traditionally, in the Computer Aided Engineering (CAE) world, road load data for various road surfaces are measured/predicted and fatigue life is predicted for each individual road surface. Fatigue life for the complete test schedule is then calculated with Miner’s rule by summing fatigue damage for each road surface with an appropriate number of repetitions. A major pitfall of this approach is that it does not consider the effect of the largest rainflow range across the entire test schedule. The method described in this paper was developed to perform fatigue analysis of structures subjected to diverse road surfaces and also consider the case in which the maximum overall peak and minimum overall valley do not occur over the same road surface.

Consumer expectations for automated vehicle operations such as automatic locking, remote ignition control, navigation, and entertainment are primary drivers for the increasing complexity of embedded automotive electronics modules. The prevalent practice for procuring these modules is to develop a written behavioral specification that is then used by an outside supplier to build and test the module. Validation test plans are written separately based on an understanding of the requirements. The challenges posed by the current practice include the inability to completely specify the expected behavior in a timely manner, the need to balance the design between low cost and new features demanded by the customer, and ensuring that the product exactly implements the specified behavior. Moreover, vehicle manufacturers desire the ability to explore sensitivity of specifications by identifying constraints on the system and assessing the product for ease of implementation.

Over the past five years, the US Automotive Materials Partnership (USAMP) has brought together representatives from DaimlerChrysler, General Motors, Ford Motor Company and over 40 other participant companies from the Mg casting industry to create and test a low-cost, Mg-alloy engine that would achieve a 15 - 20 % Mg component weight savings with no compromise in performance or durability. The block, oil pan, and front cover were redesigned to take advantage of the properties of both high-pressure die cast (HPDC) and sand cast Mg creep- resistant alloys. This paper describes the alloy selection process and the casting and testing of these new Mg-variant components. This paper will also examine the lessons learned and implications of this pre-competitive technology for future applications.

An improvement in a vehicle's front of dash barrier assembly's acoustical performance has in the past been addressed by both adding individual absorbers and increasing the overall weight of the dash sound barrier assembly. Depending upon the target market of the vehicle, adding mass may not be an option for improved acoustical performance. Understanding the value of an increase in vehicle mass and / or cost for a specific level of improved acoustical performance continues to plague both Original Equipment Manufacturer (OEM) Engineers and Purchasing representatives. This paper examines the importance of properly sealing the front of dash pass-through areas and offers recommendations which can improve the overall vehicle acoustical performance without the addition of cost and mass to the vehicle.

Corner filling is a benchmark experiment in tube hydroforming. It was designed to gain knowledge pertinent of this new fabrication process. The corner filling benchmark has been widely used in the automotive and steel industries. Common sense as well as physical tests suggests that friction is an important parameter that affects the deformation of the tube and the bursting of the tubes. However, numerical simulations have yet to verify this fact. In this paper, the stress/strain states in the tube were computed using a finite element model. The dependence of bursting on friction for corner filling was estimated by using the forming limit diagram and a tensile-based failure criterion.

Tensile measurements and fracture surface analysis of low carbon heat-treated boron steel are reported. Tensile coupons were quasi-statically deformed to fracture in a miniature tensile testing stage with custom data acquisition software. Strain contours were computed via a digital image correlation method that allowed placement of a digital strain gage in the necking region. True stress-true strain data corresponding to the standard tensile testing method are presented for comparison with previous measurements. Fracture surfaces were examined using scanning electron microscopy and the deformation mechanisms were identified.

An advanced variable valve actuation (VVA) system is characterized following end-of-life testing to enable fuel economy solutions for passenger car applications. The system consists of a switching roller finger follower (SRFF) combined with a dual feed hydraulic lash adjuster and an oil control valve that are integrated into a four cylinder gasoline engine. The SRFF provides discrete valve lift capability on the intake valves. The motivation for designing this type of VVA system is targeted to improve fuel economy by reducing the air pumping losses during part load engine operation. This paper addresses the durability of a SRFF for meeting passenger car durability requirements. Extensive durability tests were conducted for high speed, low speed, switching, and cold start operation. High engine speed test results show stable valvetrain dynamics above 7000 engine rpm. System wear requirements met end-of-life criteria for the switching, sliding, rolling and torsion spring interfaces.

This paper presents the new techniques/methods being used for the rapid vehicle development and system level performance assessment. It consists of two parts: the first part presents the automated multilevel substructuring (AMLS) technique, which greatly reduces the computational demands of larger finite element models with millions of degrees of freedom(DOF) and extends the capabilities to higher frequencies and higher level of accuracy; the second part is on the superelement in conjunction with the Component Mode Synthesis (CMS) and also Automated Component Mode Synthesis (ACMS) techniques. In superelement, a full vehicle model is divided into components such as Body-in-white, Front cradle/chassis, Rear cradle/chassis, Exhaust, Engine, Transmission, Driveline, Front suspension, Rear suspension, Brake, Seats, Instrument panel, Steering system, tires, etc. with each piece represented by reduced stiffness, mass, and damping matrices.

A series of tests were performed to determine the influence of curvature on the forming limits of 1008 AK steel. Rectangular blanks cut from three thicknesses of the material from 0.69 mm to 1.04 mm were securely clamped at opposite edges and stretched over wedge shaped punches of different radii. A series of punches were used with radii that varied from 0.508 mm to 12.7 mm to produce bending effects that range from severe to mild. Measurements show that the neck forms on the convex surface when the strain on the concave side of the sheet reaches a value consistent with the forming limit in plane-strain for in-plane deformation.

Managing (minimizing and optimizing) the total mass of a vehicle is recognized as a critical task during the development of a new vehicle, as well as throughout its production lifecycle. This paper summarizes a literature review of, and investigation into, the strategies, methods and best practices for achieving low total mass in new vehicle programs, and/or mass reductions in existing production vehicle programs. Empirical and quantitative data and examples from the automotive manufacturers and suppliers are also provided in support of the material presented.

One of the most common applications of planetary (epi-cyclic) gear sets is found in automotive transmissions. A planetary gear set typically total torque applied to be shared by multiple planets making a higher power density possible. This advantage of the planetary gear sets relies heavily on the assumption that each pinion carries an equal share of the total torque applied. However, in production, gear manufacturing and assembly variations along with certain design parameters may prevent equal load sharing among the planets. Here, a generalized mathematical model of a single-stage planetary gear set having n planets is developed to predict load shared by each planet under quasi-static conditions. The model takes into account effects of two most common errors including pinion carrier errors and gear run-out errors. Results of an experimental test program are used to validate the predictions of the model. Generalized guidelines for equal load sharing are also presented.

A computer assisted development technique for Quick Plastic Forming parts [1] is described, based on the simulation program PAM-STAMP [2]. The technique allows thickness changes during forming to be accurately considered in the development process without physical trials. Process pressure cycles, which provide for maximal material formability, can be determined with a single simulation. The paper describes new program features, which reduce modeling effort and increase simulation accuracy. Various validation examples and industrial case studies are also presented, demonstrating current capabilities.

Neck injury assessment is part of the FMVSS208 requirements. Hardware tests are often conducted to validate whether the vehicle safety system meets the requirements. This paper presents a full vehicle finite element model using LS-DYNA, including structural components, restraint system components, and dummies. In the case of a frontal impact at 30deg angle, in the areas of neck compression, neck extension and neck kinematics, it is demonstrated that a good correlation is achieved between the response of a FE dummy in the model and those of ATDs in the physical hardware tests. It is concluded that the math tool may be applied to comprehend test and design variations that may arise throughout a vehicle development lifecycle and to help develop a vehicle restraint system.

Under the initiative of the United States Council for Automotive Research LLC (USCAR§) Transmission Working Group, a collaborative effort was made with LuK USA LLC to study the influence of the friction interface parameters on the shudder durability of a wet launch clutch. Clutch configurations with different combinations of four friction materials (A, B, C and D), three groove patterns (waffle, radial and waffle-parallel) and two separator plate conditions (nitrided and non-nitrided) were considered. Durability testing consisted of a test profile, with 110 kJ energy per test cycle, developed earlier in this project. Materials A, B and C with nitrided separator plates reached the end of test criteria for the torque gradient and showed shudder. Materials B and C were more wear resistant as compared to materials A and D. The loss of friction coefficient (μ) was lower for materials B, C and D as compared to material A.

The staircase fatigue test method is a well-established, but poorly understood probe for determining fatigue strength mean and standard deviation. The sensitivity of results to underlying distributions was studied using Monte Carlo simulation by repeatedly sampling known distributions of hypothetical fatigue strength data with the staircase test method. In this paper, the effects of the underlying distribution on staircase test results are presented with emphasis on original normal, lognormal, Weibull and bimodal data. The results indicate that the mean fatigue strength determined by the staircase testing protocol is largely unaffected by the underlying distribution, but the standard deviation is not. Suggestions for conducting staircase tests are provided.

Eight lateral dolly rollover tests were conducted on 1983 Chevrolet Malibusata nominal speed of 51.5 km/h (32 mi/h). Four of the vehicles had rollcages, and four had standard production roofs. Unrestrained outboard front GM Hybrid ill dummies with head and neck transducers were used. Numerous cameras documented the vehicle and dummy movements. Detailed vehicle kinematics data allowed quantitative analysis of the conditions for head and neck loads. For both roof structures, the dummies moved upward and outward from their seats due to rotation and acceleration of the vehicle. High head/neck loads were measured when the head contacted a part of the car experiencing a large change in velocity, often that part of the car which struck the ground. The results of this work indicate that roof strength is not an important factor in the mechanics of head/neck injuries in rollover collisions for unrestrained occupants.