Search Results

Hydrocarbon permeation is one of the remaining main sources of vehicle evaporative hydrocarbon emission. However, very little information exists on the role of fuel properties on permeation losses. Therefore, experimental and modeling studies were conducted to determine the relationships between hydrocarbon permeation through HDPE (high density polyethylene) and fuel properties. Half-gallon HDPE bottles without EVOH were used in this study, because they were easily available and because steady state permeation can be measured in a matter of few days instead of several months in the case of HDPE/EVOH bottles. A permeation equation was developed using both theory and experimental data, which shows that permeation increases exponentially with fuel aromatic content, increases linearly with fuel RVP, and increases exponentially with temperature. The equation is useful for predicting how fuel and ambient temperature affect hydrocarbon permeation through vehicle fuel system.

Strip cast AA5754 sheets are of interest for automotive interior panel applications. However, Portevin-Le Chatelier (PLC) bands are seen in this material and cause surface quality concerns. Moreover, shear banding is the main failure mechanism of this material. However, the relationship between PLC bands and shear bands is still controversial in the literature. In order to delineate this problem, the digital image correlation (DIC) strain mapping technique is used to explore the three-dimensional structures of PLC bands and shear bands in AA5754 sheets. Two-dimensional DIC measurements were carried out simultaneously on both of the sheet sample surfaces (front and back side) of an AA5754 tensile sample using a commercially available optical strain mapping DIC-based system (Aramis). DIC measurements were also conducted on the thickness direction. Based on the strain mapping results, the three dimensional structures of both PLC bands and shear bands are constructed.

As part of a cooperative development program, six diesel fuels (a reference and five blends containing oxygenates) were evaluated under four steady-state conditions using a prototype 1.26-L 3-cylinder four-valve common-rail DI diesel engine. All of the fuels contained low sulfur (mostly < 5 ppm by mass), and they were chosen to determine the impacts of oxygenate volatility, concentration, and chemical type (paraffinic or aromatic) on exhaust emissions - with particular emphasis on particulate emissions. In addition to HC, CO, NOx and PM emissions measurements, emissions of the volatile portion of the PM and particle size were determined. Relative to the very low sulfur reference fuel, the oxygenated fuels reduced PM and NOx under some operating conditions, but produced little effect on either HC or CO emissions. Aliphatic oxygenates at 6 wt. percent oxygen in the reference fuel reduced simulated FTP PM emissions by 15 - 27 %.

The recyclability of co-extruded multilayer fuel tanks, and characterization of the materials used in their manufacture, have been investigated. The ethylene-vinyl alcohol, EvOH, copolymer barrier layer, extruded as a sandwich between two adhesive layers of a maleated linear low density polyethylene, LLDPE, is surrounded by three high density polyethylene, HDPE, layers, one of which is composed of the regrind derived from the waste generated by manufacture. Particular attention has been focused on the mechanism of adhesion between the barrier layer and the adhesive layers. Surface analysis of the in situ surfaces has confirmed the formation of chemical bonds between the two polymers. Morphological information, concerning dispersion of the barrier layer in the HDPE matrix during recycling, has been obtained by scanning (SEM) and transmission (TEM) electron microscopy techniques.

Thin films of liquid fuel can form on the piston surface in spark-ignited direct-injection (SIDI) engines. These fuel films can result in pool fires that lead to deposit formation and increased hydrocarbon (HC) and smoke emissions. Previous investigations of the effects of piston fuel films on engine-out HC and smoke emissions have been hampered by their inability to measure the fuel-film mass in operating direct-injection engines. In this paper, a recently developed high-speed refractive-index-matching imaging technique is used for quantitative time- and space-resolved measurements of fuel-film mass on a quartz piston window of an optically-accessible direct-injection engine operating over a range of fully-warmed-up stratified-charge conditions with both a high-pressure hollow-cone swirl-type injector and with a high-pressure multihole injector.

This paper presents an overview of techniques for measuring friction using bench tests and fired engines. The test methods discussed have been developed to provide efficient, yet realistic, assessments of new component designs, materials, and lubricants for in-cylinder and overall engine applications. A Cameron-Plint Friction and Wear Tester was modified to permit ring-in-piston-groove movement by the test specimen, and used to evaluate a number of cylinder bore coatings for friction and wear performance. In a second study, it was used to evaluate the energy conserving characteristics of several engine lubricant formulations. Results were consistent with engine and vehicle testing, and were correlated with measured fuel economy performance. The Instantaneous IMEP Method for measuring in-cylinder frictional forces was extended to higher engine speeds and to modern, low-friction engine designs.

A new core binder system (1) was used to produce foundry cores for casting hollow aluminum suspension parts by the low pressure, gravity flow, semi-permanent mold method. These and other prototype aluminum parts made using the system demonstrate that easy core removal from complex castings, core and sand recycling, and an improved environment in the core making facilities will increase productivity, improve product quality and reduce manufacturing costs.

Multidimensional simulations of coupled intake port/valve and in-cylinder flow structures in a pancake-shape combustion chamber engine are reported. The engine calculations include moving piston, moving intake valve, and valve stem. Direct comparisons of three intake configurations for the same cylinder geometry are presented: (1) standard intake valve; (2) intake valve with high-swirl shroud orientation; and (3) intake valve with across-head shroud orientation. In order to verify the calculated results, qualitative flow visualization experiments were carried out for the same intake geometries during the induction process using a transient water analog. During the intake process the results of the multidimensional simulation agreed very well with the qualitative flow visualization experiments.

Selective Catalytic Reduction (SCR) is effective over a wide temperature window to reduce NOx emissions from engine exhaust during lean operations. In this study, different supplier SCR catalysts are investigated and modeled. A global Ammonia SCR reaction mechanism has been used, and kinetic parameters for selective catalytic reduction of NOx by Ammonia were developed for both Copper (Cu)-zeolite and Iron (Fe)-zeolite SCR catalysts. The kinetic analysis was performed using a commercial one dimensional (1-D) aftertreatment code, coupled with an optimizer. The optimized kinetics have been validated extensively with laboratory reactor data for various operating conditions on three supplier catalysts - two Copper and one Iron based formulations. Both steady state and transient tests are performed and the developed SCR models are shown to agree with the experimental measurements reasonably well.

We have studied the formability of continuous strip cast (CC) AA5754 aluminum alloy for automotive applications. Strip casting technology can considerably reduce material cost compared with conventional direct chill (DC) cast aluminum sheets. However, the CC material tends to exhibit much less post-localization deformation and lower fracture strains compared with DC sheets with similar Fe content, although both alloys show similar strains for the onset of localization. Bendability of the CC alloy is also found to be inferior. The inferior behavior (post-necking and bendability) of the CC alloy can be attributed to the higher incidence of stringer-type particle distributions in the alloy. The formability of the AA5754 alloy has also been studied using two dimensional microstructure-based finite element modeling. The microstructures are represented by grains and experimentally measured particle distributions.

The accurate prediction of burst of hydroformed tubes is a research area of considerable importance in order to evaluate a design before prototyping. This report applies the presently available criteria (forming limit diagram, stress-based forming limit diagram, extended stress based forming limit curve and the plastic strain criterion) to some of the benchmark examples carried out by the Auto/Steel partnership. It was found that the formability predictions are lowest if the plastic strain criterion is used and highest if either the stress-based criteria are used. Predicted and measured results were also compared.

The use of sheet magnesium for automobile body applications is limited, in part, due to its low room temperature formability. Elevated temperature forming of magnesium sheet could enable the manufacture of automobile body closure and structural panels to meet vehicle mass targets. The effect of temperature in improving the formability of sheet magnesium has been known since the 1940's; however, automobile applications for sheet magnesium still have been very limited. The present work characterizes the elevated temperature mechanical behavior of commercially available magnesium sheet alloys at temperatures between 300°C and 500°C. The materials are then evaluated using both warm forming and superplastic forming technologies.

This study investigated the effects of piston Crevice geometry on the steady-state engine-out hydrocarbons (HC) from a Saturn DOHC four-cylinder production engine. A 50% reduction in top-land height produced about 20-25% reduction in HC emissions, at part loads. The effect of top-land radial clearance on HC emissions was found to depend on the value of top-land height, which suggests a complex relation between flame propagation in the piston crevice and crevice geometry. For idle, increasing top-land clearance resulted in an increase in HC emissions. This trend is opposite to the trend at part load. A simple model was developed which predicts surprisingly well the contribution of piston crevices to HC emissions. It was estimated that for the test engine, piston crevices contribute about 50% of the engine-out hydrocarbons. Finally exhaust gas recirculation appears to decrease the sensitivity of HC emissions to crevice dimensions.

The effects on engine-out HC emissions of a premixed propane system, and three PFI systems employing different types of injectors and using Phase II gasoline were investigated on a four-cylinder DOHC spark-ignition engine. Cold conditions resulted in significant increases in engine-out HC emissions. Phase II gasoline caused much higher emissions of HC than propane fuel. The difference in the HC emissions from the two fuels increased dramatically with lowering the coolant temperature of the engine. At cold conditions, liquid fuel entering the combustion chamber appears to be the primary source of engine out HC emissions. At the coldest temperature tested the estimated percent contribution of in-cylinder liquid fuel to the observed increase of HC emissions was as much as 96%.

In the twenty-first century, exhaust emission control will remain a major technical challenge especially as additional pressures for fuel and energy conservation mount. To address these needs, a wide variety of engine and powertrain options must be considered. For many reasons, the piston engine will remain the predominant engine choice in the twenty-first century, especially for conventional and/or parallel hybrid drive trains. Emissions constraints favor the conventional port fuel-injected gasoline engine with 3-way exhaust catalyst, while energy conservation favors direct-injection gasoline and diesel engines. As a result of recent technological progress from a competitive European market, diesels, and most recently, direct-injection (DI) diesels now offer driveability and performance characteristics competitive with those of gasoline engines. In addition, DI diesels offer the highest fuel efficiency.

An engine system finite-element model is developed and experimentally evaluated for predicting the structural vibration and radiated noise of the running engine. Combustion and inertial loads from a rigid-body dynamic analysis of the crank-piston motion are applied as operating loads in the model. Comparisons are made with measurements of the structural vibration and radiated noise of a running engine. The comparisons show that the accuracy of the model in predicting structural vibration and radiated noise is generally adequate.

A family of low-cost, creep-resistant magnesium alloys has been developed. These alloys, containing aluminum, calcium, and strontium are designated as “ACX” alloys. Developed for engine blocks and transmissions, the “ACX” alloys have at least 40% greater tensile and 25% greater compressive creep resistance than AE42, and corrosion resistance as good as AZ91D (GMPG 9540P/B corrosion test). These alloys are estimated to cost only slightly more than AZ91D and have as good castability. Creep data up to 200°C, tensile properties at room temperature and 175°C, corrosion results and microstructure analysis are presented and discussed. These alloys have the potential to enable the extension of the substantial weight reduction benefits of magnesium to powertrain components.

Over the last two decades, advanced engine control systems have been developed that use cylinder pressure as the primary feedback variable. Production application has been limited by cost, reliability, and packaging difficulties associated with intrusive cylinder pressure sensors. Now, a low-cost cylinder-pressure-based engine control system has been developed that utilizes Pressure-Ratio Management (PRM) and non-intrusive cylinder pressure sensors mounted in the spark plug boss of four-valve-per-cylinder engines. The system adaptively optimizes individual-cylinder spark timing and air-fuel ratio, and overall exhaust gas recirculation (EGR) for best fuel economy and lowest emissions over the life of each vehicle. This paper presents the engine control and cylinder pressure sensor systems. Results are presented showing spark timing and EGR control, knock and misfire detection, cylinder-to-cylinder air/fuel balancing, and cold start control.

Federal standards that mandate improved fuel economy have resulted in the increased use of lightweight materials in automotive applications. However, the environmental burdens associated with a product extend well beyond the use phase. Life cycle assessment is the science of determining the environmental burdens associated with the entire life cycle of a given product from cradle-to-grave. This report documents the environmental burdens associated with every phase of the life cycle of two fuel tanks utilized in full-sized 1996 GM vans. These vans are manufactured in two configurations, one which utilizes a steel fuel tank, and the other a multi-layered plastic fuel tank consisting primarily of high density polyethylene (HDPE). This study was a collaborative effort between GM and the University of Michigan's National Pollution Prevention Center, which received funding from EPA's National Risk Management Research Laboratory.

The design of pockets on automotive sheet metal parts can significantly affect part formability. We have developed regression formulas for predicting the failure depth of a symmetric rectangular pocket as a function of the geometric parameters that define the pocket. The formulas were developed by statistically selecting combinations of geometric pocket parameters for formability analysis and using formability simulations to determine the pocket failure depth for each selected parameter combination. The regression formulas were tested by comparing their predictions with simulations for combinations of part parameters not used to develop the formulas.