Search Results

Hydrocarbon permeation is one of the remaining main sources of vehicle evaporative hydrocarbon emission. However, very little information exists on the role of fuel properties on permeation losses. Therefore, experimental and modeling studies were conducted to determine the relationships between hydrocarbon permeation through HDPE (high density polyethylene) and fuel properties. Half-gallon HDPE bottles without EVOH were used in this study, because they were easily available and because steady state permeation can be measured in a matter of few days instead of several months in the case of HDPE/EVOH bottles. A permeation equation was developed using both theory and experimental data, which shows that permeation increases exponentially with fuel aromatic content, increases linearly with fuel RVP, and increases exponentially with temperature. The equation is useful for predicting how fuel and ambient temperature affect hydrocarbon permeation through vehicle fuel system.

As part of a cooperative development program, six diesel fuels (a reference and five blends containing oxygenates) were evaluated under four steady-state conditions using a prototype 1.26-L 3-cylinder four-valve common-rail DI diesel engine. All of the fuels contained low sulfur (mostly < 5 ppm by mass), and they were chosen to determine the impacts of oxygenate volatility, concentration, and chemical type (paraffinic or aromatic) on exhaust emissions - with particular emphasis on particulate emissions. In addition to HC, CO, NOx and PM emissions measurements, emissions of the volatile portion of the PM and particle size were determined. Relative to the very low sulfur reference fuel, the oxygenated fuels reduced PM and NOx under some operating conditions, but produced little effect on either HC or CO emissions. Aliphatic oxygenates at 6 wt. percent oxygen in the reference fuel reduced simulated FTP PM emissions by 15 - 27 %.

A new after-treatment system called DPNR (Diesel Particulate-NOx Reduction System) has been developed for simultaneous and continuous reduction of particulate matter (PM) and nitrogen oxides (NOx) in diesel exhaust gas. This system consists of both a new catalytic technology and a new diesel combustion technology which enables rich operating conditions in diesel engines. The catalytic converter for the DPNR has a newly developed porous ceramic structure coated with a NOx storage reduction catalyst. A fresh DPNR catalyst reduced more than 80 % of both PM and NOx. This paper describes the concept and performance of the system in detail. Especially, the details of the PM oxidation mechanism in DPNR are described.

The recyclability of co-extruded multilayer fuel tanks, and characterization of the materials used in their manufacture, have been investigated. The ethylene-vinyl alcohol, EvOH, copolymer barrier layer, extruded as a sandwich between two adhesive layers of a maleated linear low density polyethylene, LLDPE, is surrounded by three high density polyethylene, HDPE, layers, one of which is composed of the regrind derived from the waste generated by manufacture. Particular attention has been focused on the mechanism of adhesion between the barrier layer and the adhesive layers. Surface analysis of the in situ surfaces has confirmed the formation of chemical bonds between the two polymers. Morphological information, concerning dispersion of the barrier layer in the HDPE matrix during recycling, has been obtained by scanning (SEM) and transmission (TEM) electron microscopy techniques.

Thin films of liquid fuel can form on the piston surface in spark-ignited direct-injection (SIDI) engines. These fuel films can result in pool fires that lead to deposit formation and increased hydrocarbon (HC) and smoke emissions. Previous investigations of the effects of piston fuel films on engine-out HC and smoke emissions have been hampered by their inability to measure the fuel-film mass in operating direct-injection engines. In this paper, a recently developed high-speed refractive-index-matching imaging technique is used for quantitative time- and space-resolved measurements of fuel-film mass on a quartz piston window of an optically-accessible direct-injection engine operating over a range of fully-warmed-up stratified-charge conditions with both a high-pressure hollow-cone swirl-type injector and with a high-pressure multihole injector.

This paper presents an overview of techniques for measuring friction using bench tests and fired engines. The test methods discussed have been developed to provide efficient, yet realistic, assessments of new component designs, materials, and lubricants for in-cylinder and overall engine applications. A Cameron-Plint Friction and Wear Tester was modified to permit ring-in-piston-groove movement by the test specimen, and used to evaluate a number of cylinder bore coatings for friction and wear performance. In a second study, it was used to evaluate the energy conserving characteristics of several engine lubricant formulations. Results were consistent with engine and vehicle testing, and were correlated with measured fuel economy performance. The Instantaneous IMEP Method for measuring in-cylinder frictional forces was extended to higher engine speeds and to modern, low-friction engine designs.

Multidimensional simulations of coupled intake port/valve and in-cylinder flow structures in a pancake-shape combustion chamber engine are reported. The engine calculations include moving piston, moving intake valve, and valve stem. Direct comparisons of three intake configurations for the same cylinder geometry are presented: (1) standard intake valve; (2) intake valve with high-swirl shroud orientation; and (3) intake valve with across-head shroud orientation. In order to verify the calculated results, qualitative flow visualization experiments were carried out for the same intake geometries during the induction process using a transient water analog. During the intake process the results of the multidimensional simulation agreed very well with the qualitative flow visualization experiments.

Selective Catalytic Reduction (SCR) is effective over a wide temperature window to reduce NOx emissions from engine exhaust during lean operations. In this study, different supplier SCR catalysts are investigated and modeled. A global Ammonia SCR reaction mechanism has been used, and kinetic parameters for selective catalytic reduction of NOx by Ammonia were developed for both Copper (Cu)-zeolite and Iron (Fe)-zeolite SCR catalysts. The kinetic analysis was performed using a commercial one dimensional (1-D) aftertreatment code, coupled with an optimizer. The optimized kinetics have been validated extensively with laboratory reactor data for various operating conditions on three supplier catalysts - two Copper and one Iron based formulations. Both steady state and transient tests are performed and the developed SCR models are shown to agree with the experimental measurements reasonably well.

This study investigated the effects of piston Crevice geometry on the steady-state engine-out hydrocarbons (HC) from a Saturn DOHC four-cylinder production engine. A 50% reduction in top-land height produced about 20-25% reduction in HC emissions, at part loads. The effect of top-land radial clearance on HC emissions was found to depend on the value of top-land height, which suggests a complex relation between flame propagation in the piston crevice and crevice geometry. For idle, increasing top-land clearance resulted in an increase in HC emissions. This trend is opposite to the trend at part load. A simple model was developed which predicts surprisingly well the contribution of piston crevices to HC emissions. It was estimated that for the test engine, piston crevices contribute about 50% of the engine-out hydrocarbons. Finally exhaust gas recirculation appears to decrease the sensitivity of HC emissions to crevice dimensions.

The effects on engine-out HC emissions of a premixed propane system, and three PFI systems employing different types of injectors and using Phase II gasoline were investigated on a four-cylinder DOHC spark-ignition engine. Cold conditions resulted in significant increases in engine-out HC emissions. Phase II gasoline caused much higher emissions of HC than propane fuel. The difference in the HC emissions from the two fuels increased dramatically with lowering the coolant temperature of the engine. At cold conditions, liquid fuel entering the combustion chamber appears to be the primary source of engine out HC emissions. At the coldest temperature tested the estimated percent contribution of in-cylinder liquid fuel to the observed increase of HC emissions was as much as 96%.

In the twenty-first century, exhaust emission control will remain a major technical challenge especially as additional pressures for fuel and energy conservation mount. To address these needs, a wide variety of engine and powertrain options must be considered. For many reasons, the piston engine will remain the predominant engine choice in the twenty-first century, especially for conventional and/or parallel hybrid drive trains. Emissions constraints favor the conventional port fuel-injected gasoline engine with 3-way exhaust catalyst, while energy conservation favors direct-injection gasoline and diesel engines. As a result of recent technological progress from a competitive European market, diesels, and most recently, direct-injection (DI) diesels now offer driveability and performance characteristics competitive with those of gasoline engines. In addition, DI diesels offer the highest fuel efficiency.

An engine system finite-element model is developed and experimentally evaluated for predicting the structural vibration and radiated noise of the running engine. Combustion and inertial loads from a rigid-body dynamic analysis of the crank-piston motion are applied as operating loads in the model. Comparisons are made with measurements of the structural vibration and radiated noise of a running engine. The comparisons show that the accuracy of the model in predicting structural vibration and radiated noise is generally adequate.

The whirl noise on turbochargers is generated by the self-induced vibration of the oil film in the bearing system. The noise is characterized by its frequency behavior that doesn't increase proportionately to the turbo shaft speed. It tends to be felt annoying. In this paper, to improve the whirl vibration, a statistical analysis approach was applied to the bearing specifications. The results from experiments showed that the bearing clearances played an important role in the reduction of the whirl vibration. To further investigate into this phenomenon, the shaft oscillation behavior was measured. And a vibration simulation program for the turbocharger bearing system was also developed.

A family of low-cost, creep-resistant magnesium alloys has been developed. These alloys, containing aluminum, calcium, and strontium are designated as “ACX” alloys. Developed for engine blocks and transmissions, the “ACX” alloys have at least 40% greater tensile and 25% greater compressive creep resistance than AE42, and corrosion resistance as good as AZ91D (GMPG 9540P/B corrosion test). These alloys are estimated to cost only slightly more than AZ91D and have as good castability. Creep data up to 200°C, tensile properties at room temperature and 175°C, corrosion results and microstructure analysis are presented and discussed. These alloys have the potential to enable the extension of the substantial weight reduction benefits of magnesium to powertrain components.

Over the last two decades, advanced engine control systems have been developed that use cylinder pressure as the primary feedback variable. Production application has been limited by cost, reliability, and packaging difficulties associated with intrusive cylinder pressure sensors. Now, a low-cost cylinder-pressure-based engine control system has been developed that utilizes Pressure-Ratio Management (PRM) and non-intrusive cylinder pressure sensors mounted in the spark plug boss of four-valve-per-cylinder engines. The system adaptively optimizes individual-cylinder spark timing and air-fuel ratio, and overall exhaust gas recirculation (EGR) for best fuel economy and lowest emissions over the life of each vehicle. This paper presents the engine control and cylinder pressure sensor systems. Results are presented showing spark timing and EGR control, knock and misfire detection, cylinder-to-cylinder air/fuel balancing, and cold start control.

Federal standards that mandate improved fuel economy have resulted in the increased use of lightweight materials in automotive applications. However, the environmental burdens associated with a product extend well beyond the use phase. Life cycle assessment is the science of determining the environmental burdens associated with the entire life cycle of a given product from cradle-to-grave. This report documents the environmental burdens associated with every phase of the life cycle of two fuel tanks utilized in full-sized 1996 GM vans. These vans are manufactured in two configurations, one which utilizes a steel fuel tank, and the other a multi-layered plastic fuel tank consisting primarily of high density polyethylene (HDPE). This study was a collaborative effort between GM and the University of Michigan's National Pollution Prevention Center, which received funding from EPA's National Risk Management Research Laboratory.

This paper describes a bench method to evaluate the frictional behavior, under scuffing conditions, of some test coupons of standard materials currently used in making cylinder bores and pistons. The usefulness of this method is in evaluating new materials and coatings that may enable the elimination of iron liners from engine blocks. While investigating the potential application of Plasma Source Ion Implantation (PSII) on engine piston/bore materials, we have systematically studied the scuffing related friction behavior of aluminum 390 alloy and cast iron. A pin-on-disk tribometer is used under dry sliding conditions. Testing parameters for simulating cold scuff in bench tests have been specified. This proposed test method offers a screening tool desirable for the development of PSII technology and may also be useful for the design of other new surface modification techniques.

All air bag systems use a pyrotechnic combustion process for the generation of gases. In some systems, it is also used for the heating of stored gases to quickly inflate the air bag. As a by-product of the process, gases and particles are produced that enter the passenger compartment resulting in inhalation of these substances. We have previously shown that systems using sodium azide as the gas generant can initiate asthmatic attacks in susceptible individuals. To evaluate whether the effluents from new-generation, non-azide air bag systems also have the potential to produce adverse responses, we performed controlled exposures of mild to moderate asthmatics to the effluents from six of these air bag systems. Each volunteer asthmatic subject was pulmonary function tested (baseline), and then seated in the back seat of the test vehicle. The air bag system was deployed and the subjects remained in the vehicle for twenty minutes.

A novel, fully flexible engine valve actuation mechanism was built and tested for the first time. It consists of a permanent magnet brushless dc motor driving a cam mechanism to actuate each engine poppet valve. This mechanism has the advantages of low friction, low seating velocity and speed range comparable to that of production valve trains. The electromechanical system has also regeneration capabilities which result in an energy requirement that is equivalent to or lower than the valve-train friction of current production engines. The valve event duration is changed by increasing or decreasing the cam/motor angular velocity during valve opening in order to shorten or lengthen the valve event, respectively. Part-lift operation is also possible by oscillating the mechanism around the valve opening or closing points. The prototype mechanism was run on the bench on an actual engine cylinder head at speeds of up to 3225 r/min, equivalent to 6450 engine r/min.

An efficient light weight 425 Watts charging system was developed and built to meet the requirements of a 12-cylinder engine for racing application. The new system consists of a permanent magnet (PM) alternator with MAGNEQUENCH (MQ3) magnets and a high frequency switching regulator to regulate the output voltage over the engine speed range of 2,000-12,000 rpm. The system has been tested for 75% overall efficiency as compared to 38% for the present system over most of the speed range. Excellent dynamic response (less than 1 ms) has been measured, which allows the alternator to support pulsed loads, even if the battery is disconnected during operation. The new system weighs 3.73 kg vs 5.4 kg of the existing system.