Search Results

This paper introduces the details of a low noise design realized by fully utilizing the theoretical methods for the prediction of noise and vibration, applied to Hino's new “H07D” engine. In the development of this engine, the reduction of the vehicle interior noise was one of the highest priority aims. For this purpose, the influence of the engine noise on the vehicle noise was firstly investigated to identify the major noise sources. Then, making best use of noise prediction techniques (FEM, etc.), the noise radiation mechanisms were clarified and the components identified as major noise sources were re-designed. In these improvements, the theoretical techniques also predicted carefully the effect of design changes on the related components, including their installation in an engine as required. These procedures achieved a remarkable noise reduction of the engine by cost effective methods.

In diesel engine trucks, the sound quality improvement as well as the noise level reduction is demanded because of their annoying exterior noise. The semantic differential method was applied to evaluate the sound quality of trucks. In order to improve the analytical accuracy, subjects who can evaluate the characteristics of sound quality were statistically selected among all the subjects. Comfortability and powerfulness were extracted as the principal components by using the data of the selected subjects. It has been clarified that the comfortability strongly relates to high frequency element ratio, high frequency level, etc. The powerfulness strongly relates to the Zwicker loudness.

In Biodiesel Fuel Research Working Group(WG) of Japan Auto-Oil Program(JATOP), some impacts of high biodiesel blends have been investigated from the viewpoints of fuel properties, stability, emissions, exhaust aftertreatment systems, cold driveability, mixing in engine oils, durability/reliability and so on. This report is designed to determine how high biodiesel blends affect oil quality through testing on 2005 regulations engines with DPFs. When blends of 10-20% rapeseed methyl ester (RME) with diesel fuel are employed with 10W-30 engine oil, the oil change interval is reduced to about a half due to a drop in oil pressure. The oil pressure drop occurs because of the reduced kinematic viscosity of engine oil, which resulting from dilution of poorly evaporated RME with engine oil and its accumulation, however, leading to increased wear of piston top rings and cylinder liners.

A large-size truck is equipped with a variety of audible warning devices. These warning devices are grouped into three categories by their usage, i.e., malfunction type, proximity type and attention type. The sound characteristics of warning sound that are investigated for each type are signal envelope, fundamental frequency and the number of harmonics. Many sounds are synthesized with nine fundamental frequencies, ten or fewer harmonics and two signal envelopes. With volume fixed, these sounds are evaluated using an unpleasantness rating scale, and the functional impression of these sound is also chosen. From the results, the range of fundamental frequencies, the number of harmonics and the shapes of signal envelopes for preferable sound quality are determined.

In a tractor-trailer, ride comfort affected by horizontal human body motions, so called “wavy” and “shaky” feelings, is at issue. Insight about “wavy” and “shaky” feelings which is important for efficient vehicle development is not enough. Experiments using 6-axis motion generator and motion capture and inverse-analysis using multi-body human model indicated the characteristics of each feeling. Motion observation and transfer function indicated that while a bad subjective score of “wavy” feeling corresponds to same-phase roll motion of chest and pelvis up to 0.7Hz, “shaky” correlates to an antiphase of them around 2Hz. By multiple regression, dominant vibration components of the human body and the vehicle to subjective evaluation of the feelings above were identified. Explanatory variables for the “wavy” feeling are roll rate and lateral jerk and those for the “shaky” are lateral acceleration and longitudinal acceleration.

In this paper, the flow patterns and velocity distributions of coolant flow around cylinder liners of diesel engine are studied by numerical calculation and experimental observation. The experiment is carried out by oil film method and direct observation with a transparent acrylic cylinder liner. The calculation is performed with the 3-dimensional model by FEM for fluid flow. The motion of coolant flow by calculation corresponds with the result by oil film method and direct observation with transparent cylinder liner. The visualization of the 3-dimensional calculation gives a good understanding about motion of coolant flow and pressure distribution in water chamber. This method is applied to improve the coolant flow with the stagnation around cylinder liner. The effect of improved design is confirmed by experiment. That is, there are no stagnations in the flow around cylinder liners.

The noise-generating mechanism of a reciprocating air compressor for heavy duty vehicles during idling was investigated. It was elucidated that the gear rattling noise of the air compressor drive gear train caused by the negative value of the air compressor drive torque was a major noise source. To completely suppress the gear rattling phenomenon, a new loading device with an air cylinder that cancels the negative value of the air compressor drive torque was fabricated. When the loading device was worked, the impulsive sound level was reduced to 10 dB(A). It was found that the impulsive sound level during gear rattling is closely related to the difference in gear teeth velocity between the crankshaft gear and the air compressor drive gear, as one of the characteristics that are needed to obtain a guide for carrying out estimations in the calculation simulation.

Noise reduction of diesel engines installed in heavy duty vehicles is one of the highest priorities from the viewpoints of meeting the regulations for urban traffic noise abatement and noise reduction in the cabin for lightening fatigue with comfortable long driving. It is necessary that noise reduction measures then be applied to those causes. Noise reduction measures for the diesel engine can be classified into five categories on the noise radiation block-diagram. These are, reduction of combustion and mechanical forces, deformation and vibration control of cylinder block, vibration control of fastened components, prevention of standing wave and close fitting shields. All noise reduction measures for the diesel engine researched for the purpose of practical use are fully described in this paper.

The separation of combustion noise and mechanical noise from the total noise of a four-cylinder in-line diesel engine at idling was carried out with high accuracy by changing the fuel injection timing. The mechanical noise, which accounts for the major share at 93%, was then separated into noises from the typical mechanical causes, and the valve train was found to be the major noise source. From analysis of the noise generating mechanism for the valve train, it was clarified that the noise was caused mainly by the gear rattling owing to the variation in the camshaft drive torque.

Reducing friction between the piston ring and cylinder is an effective way of meeting the demand for lower fuel consumption in vehicle engines. To that effect, the authors have proposed a new and efficient friction reduction treatment for the cylinder. At first glance, this treatment seems similar to typical microtexture treatments, but it is built on a different approach. Through a rig tester, it was confirmed that optimizing the shape of the dimples and the treatment area for the cylinder improves FMEP between the piston ring and the cylinder liner by 17%. This report presents an analysis of the test results to explain the mechanism by which this effect is achieved. Fuel consumption was measured in an actual engine, and a maximum fuel consumption improvement of 3.2% was confirmed after conversion to the Japanese heavy duty vehicle fuel economy standards (Category T2). Lubricating oil consumption, blow-by and durability were also examined.

It is preferable that power steering permits “static park” and has a good “road Feel” when running. In order to permit “static park”, a large bore actuation cylinder with high flow pump is required. Such a method, however, has two defects, a loss power for driving a large volume pump and a poor “road feel”. Resolving these problems and achieving the above matters. Hino has developed a load sensing power steering system. This system, which employes two actuation cylinders controlled by means of a unique load sensing valve arrangement, is designed to permit use of only one cylinder for highway speeds and both cylinders during a static park maneuver. When the system is combined with the preceding speed sensing power steering, “static park” is further facilitated and a tasty “road feel” is available in accordance with vehicle speed.

Technical impacts on engine oil performance by the use of waste cooking oil as bio-diesel fuel (BDF) are not well understood while the industry has made significant progress in studies on quality specifications and infrastructure. The authors, who consist of a consortium organized by Japan Lubricating Oil Society (JALOS), examined technical effects of waste cooking oil as BDF on engine oil performance such as wear and high temperature corrosion using vehicle fleets and bench tests to identify technical issues of engine oil meeting the use of BDF. The study brings fundamental information about technical impacts of BDF on engine oils.

Hino Motors developed J-series 4.7-liter inline-four cylinder and 7.7-liter inline-six cylinder engines for complying with the 2004 U.S. exhaust emissions regulations. Several technologies were incorporated in the development process to accomplish simultaneous reductions in both exhaust emissions and fuel consumption while the engine performance, reliability, and durability were maintained at the levels acceptable for truck application. Newly developed technologies include a cooled EGR system, a common-rail fuel injection system, a VNT system, and an engine control system for harmonized control of EGR valve and VNT. This paper reports the development approaches and results.

Tooth contact marking of gears is an important quality characteristic that affects tooth strength and gear noise. Tooth contact marking measurement is generally done by painting the tooth surfaces of two meshed gears, rotating the gears and visually observing contact marks. Since it requires much working hours and experience to judge such a measurement, a method of measuring contact tooth markers by image processing has been developed. In this measurement method, the tooth surfaces of rotating gears are continuously observed by a TV camera, and the images are stored in an image memory device. Such quantities as the tooth surface size and tooth surface brightness level are set as initial settings, and the set values are compared with the observed images by a microcomputer to give the results of the measurement.

Recently, as one of the effective measures for engine noise reduction, vibration damping steel sheets (VDSS) have been increasingly applied to engine oil sumps. This paper describes the formability of VDSS. Various factors closely related to drawability are considered. This study has been carried out in a production engineering process of manufacturing exceedingly deep, single blank sheet, oil sump for heavy-duty truck diesel engines. Some treatment of the surface of the VDSS was found to be a principal factor influencing deep drawability.

The coupling behavior of the torsional, bending, and longitudinal vibrations in the crankshaft is described. The incidental excitation forces under crankshaft torsional vibration due to reciprocating and rotating masses are derived theoretically. Experiments on the coupling behavior of the crankshaft vibrations and the excitation behavior in the engine structure were performed in a four-cylinder automotive engine; their results are discussed.

A newly developed OHC (Over-Head Camshaft) prototype of a six-cylinder in-line diesel engine (with bore size: 114mm, stroke size: 130mm) was studied, comparing with the previous version of OHV (Over-Head Valve) type engine (with bore size: 110mm, stroke size: 130mm). It was found that the new type of cylinder block (with 130.8 kg of mass) has significantly lower natural frequencies than those for the previous type of cylinder block (with 133.2 kg of mass). Furthermore, slightly more predominant engine noise and vibration were induced in the new engine. The vibration behavior and the excitation force transmission characteristics were investigated by EMA (Experimental Modal Analysis). We performed a series of impact tests for (1) free-free cylinder block, (2) free-free crankshaft substructure with torsional damper and flywheel attached, and (3) the case where (1) and (2) are assembled together.

This paper describes the experimental studies of turbocharged and intercooled diesel engines with particular emphasis on combustion characteristics following increase of boost pressure. Through these studies, it has become possible to determine the optimum air quantity for minimizing fuel consumption at each engine speed range under the restrictive conditions of NOx emission, exhaust smoke and maximum cylinder pressure. Discussed also is the lack of air quantity in the low engine speed range of high-boost turbocharged diesel engines. Various turbocharging systems to improve air quantity in this speed range are introduced herein. Practically the engine performance of conventional turbocharging, waste gate control turbocharging and variable geometry turbocharging are discussed from the viewpoint of torque recovery in the low engine speed range.

Wear resistance is the important characteristics of cast iron materials for automobile components. Because the phenomenon of wear is a highly complicated mechanism involving many factors such as surface conditions, chemical reactions with lubricants, metals, and physics, it has not been fully explained. Therefore, it will be necessary to confirm and explain the wear mechanism to develop effective improvements. The purpose of this study was to investigate the structural change behavior and effects of alloying elements when the material top surface becomes worn, in order to improve the wear resistance of cylinder liners and other cast iron materials. For this purpose, several types of prototype materials were produced, and the relationship between components and wear resistance was investigated by using a laser microscope for quantitative observation of the degree of pearlite microstructure fineness.

The purpose of the investigation presented here was to develop a high quality SAE 10W-30 engine lubricating oil to meet the heavy duty operating conditions of trucks. The operation of their engines is predicted to become more severe in future because of the trend toward higher power output, nore severe regulation of exhaust emissions and noise as well as the increasing demand for better fuel economy. To meet these demands, an improvement of the wear resistance of engine lubricating oil was considered to be the most important aspect for the development of high performance diesel engines in the future. The engine test developed was able to evaluate various experimental oils by observing wear resistance of the valve train which is considered to be one of the most severe tri-bological conditions. The best oils were determined by optimum selection of the amount and type of detergent, ashless dispersant and zinc dithiophosphate.