Search Results

This paper introduces the Japanese standards and regulations of automobiles with brakes as the central subject and clarifies the difference from those of Europe and USA by comparison. Further, this paper describes not only the application status of the standards and regulations in Japan but also the features of structure and performance of Japanese trucks that are designed and produced under such standards and regulations. It can be said that the Japanese trucks are comparatively simple in structure but are in a level equal to or higher than European and USA automobiles in respect of performance. Also in respect of the international harmonization, the internationalization of standards is being conducted in Japan on the basis of ISO and the internationalization for regulations is considered to be under preparation.

This paper introduces the details of a low noise design realized by fully utilizing the theoretical methods for the prediction of noise and vibration, applied to Hino's new “H07D” engine. In the development of this engine, the reduction of the vehicle interior noise was one of the highest priority aims. For this purpose, the influence of the engine noise on the vehicle noise was firstly investigated to identify the major noise sources. Then, making best use of noise prediction techniques (FEM, etc.), the noise radiation mechanisms were clarified and the components identified as major noise sources were re-designed. In these improvements, the theoretical techniques also predicted carefully the effect of design changes on the related components, including their installation in an engine as required. These procedures achieved a remarkable noise reduction of the engine by cost effective methods.

In diesel engine trucks, the sound quality improvement as well as the noise level reduction is demanded because of their annoying exterior noise. The semantic differential method was applied to evaluate the sound quality of trucks. In order to improve the analytical accuracy, subjects who can evaluate the characteristics of sound quality were statistically selected among all the subjects. Comfortability and powerfulness were extracted as the principal components by using the data of the selected subjects. It has been clarified that the comfortability strongly relates to high frequency element ratio, high frequency level, etc. The powerfulness strongly relates to the Zwicker loudness.

A large-size truck is equipped with a variety of audible warning devices. These warning devices are grouped into three categories by their usage, i.e., malfunction type, proximity type and attention type. The sound characteristics of warning sound that are investigated for each type are signal envelope, fundamental frequency and the number of harmonics. Many sounds are synthesized with nine fundamental frequencies, ten or fewer harmonics and two signal envelopes. With volume fixed, these sounds are evaluated using an unpleasantness rating scale, and the functional impression of these sound is also chosen. From the results, the range of fundamental frequencies, the number of harmonics and the shapes of signal envelopes for preferable sound quality are determined.

In a tractor-trailer, ride comfort affected by horizontal human body motions, so called “wavy” and “shaky” feelings, is at issue. Insight about “wavy” and “shaky” feelings which is important for efficient vehicle development is not enough. Experiments using 6-axis motion generator and motion capture and inverse-analysis using multi-body human model indicated the characteristics of each feeling. Motion observation and transfer function indicated that while a bad subjective score of “wavy” feeling corresponds to same-phase roll motion of chest and pelvis up to 0.7Hz, “shaky” correlates to an antiphase of them around 2Hz. By multiple regression, dominant vibration components of the human body and the vehicle to subjective evaluation of the feelings above were identified. Explanatory variables for the “wavy” feeling are roll rate and lateral jerk and those for the “shaky” are lateral acceleration and longitudinal acceleration.

The correlation between newly approved EN 15751 and the internal diesel injector deposits (IDID) due to fuel oxidative deterioration has not been made clear. In the present research, the Rancimat method was slightly modified to research the relationship between fuel oxidative deterioration and the deterioration products generated from the fuel. After heating fuel at 120 to 150°C for a set period, insoluble deterioration products (IDID-like substances) were generated and their weights were measured. At the same time, the shifts of the conductivity in trap water were analyzed from a new perspective, and its relationship with the deterioration products was investigated. At 120°C and 130°C, conductivity rising rates after the inflection point (this set of data represents the rate of organic acid generation in the fuel, and we named “Oxidation rate”) exhibited a strong correlation with the quantity of deterioration products.

Noise reduction of diesel engines installed in heavy duty vehicles is one of the highest priorities from the viewpoints of meeting the regulations for urban traffic noise abatement and noise reduction in the cabin for lightening fatigue with comfortable long driving. It is necessary that noise reduction measures then be applied to those causes. Noise reduction measures for the diesel engine can be classified into five categories on the noise radiation block-diagram. These are, reduction of combustion and mechanical forces, deformation and vibration control of cylinder block, vibration control of fastened components, prevention of standing wave and close fitting shields. All noise reduction measures for the diesel engine researched for the purpose of practical use are fully described in this paper.

The separation of combustion noise and mechanical noise from the total noise of a four-cylinder in-line diesel engine at idling was carried out with high accuracy by changing the fuel injection timing. The mechanical noise, which accounts for the major share at 93%, was then separated into noises from the typical mechanical causes, and the valve train was found to be the major noise source. From analysis of the noise generating mechanism for the valve train, it was clarified that the noise was caused mainly by the gear rattling owing to the variation in the camshaft drive torque.

Hino Motors is about to launch a new truck model FA as a family product of the model FB class 5 category trucks which have been sold since 1986, Model FA, a class 3 category cab-over-engine truck has a GVW of 13,500 Lbs. and is powered by a 3.8 liter direct injection turbocharged diesel engine which produces 125 HP in conformity with federal exhaust gas emission regulations for 50 states. The new truck was designed and developed to satisfy several principal design objectives such as excellent maneuverability, driving comfort, superior fuel economy as well as sufficient reliability and durability within the simplest possible structure. This paper describes its design objectives, features focusing on cab and engine and technologies devoted to the development.

We have developed a new test method in which temperature of cavity lip of a piston alone during engine rotation is reproduced, cavity lip strain is measured. As the results of strain measurement using the test method in a condition that simulates of conventional engines, a strain behavior was out-of-phase. And in a condition that simulates of high-load engines in future, strain behavior was clockwise-diamond cycle. It was found from the result of the test method developed that strain increased on the cavity lip. The fatigue life of the cavity lip was evaluated using the strain measured and isothermal fatigue curves which obtained by the strain controlled isothermal fatigue test. The result of engine durability test has revealed that the developed method was valid for thermal fatigue evaluation of the cavity lip.

To reduce the vehicle fuel consumption at high speed, it is very effective to minimize the aerodynamic resistance of the vehicle, which forms most of the vehicle running resistance at high speed. This paper presents a reduction of the aerodynamic resistance of van type truck through the wind tunnel tests using 1/5 scaled model. Firstly, the aerodynamically desirable cab shape for cargo type truck is investigated by changing main cab shape factors such as corner curvatures. Secondly, several effective attachments for Van type truck are investigated, and lastly, the effect of these aerodynamic improvements on the fuel consumption are clearified by vehicle running test.

Technical impacts on engine oil performance by the use of waste cooking oil as bio-diesel fuel (BDF) are not well understood while the industry has made significant progress in studies on quality specifications and infrastructure. The authors, who consist of a consortium organized by Japan Lubricating Oil Society (JALOS), examined technical effects of waste cooking oil as BDF on engine oil performance such as wear and high temperature corrosion using vehicle fleets and bench tests to identify technical issues of engine oil meeting the use of BDF. The study brings fundamental information about technical impacts of BDF on engine oils.

Tooth contact marking of gears is an important quality characteristic that affects tooth strength and gear noise. Tooth contact marking measurement is generally done by painting the tooth surfaces of two meshed gears, rotating the gears and visually observing contact marks. Since it requires much working hours and experience to judge such a measurement, a method of measuring contact tooth markers by image processing has been developed. In this measurement method, the tooth surfaces of rotating gears are continuously observed by a TV camera, and the images are stored in an image memory device. Such quantities as the tooth surface size and tooth surface brightness level are set as initial settings, and the set values are compared with the observed images by a microcomputer to give the results of the measurement.

Recently, as one of the effective measures for engine noise reduction, vibration damping steel sheets (VDSS) have been increasingly applied to engine oil sumps. This paper describes the formability of VDSS. Various factors closely related to drawability are considered. This study has been carried out in a production engineering process of manufacturing exceedingly deep, single blank sheet, oil sump for heavy-duty truck diesel engines. Some treatment of the surface of the VDSS was found to be a principal factor influencing deep drawability.

The coupling behavior of the torsional, bending, and longitudinal vibrations in the crankshaft is described. The incidental excitation forces under crankshaft torsional vibration due to reciprocating and rotating masses are derived theoretically. Experiments on the coupling behavior of the crankshaft vibrations and the excitation behavior in the engine structure were performed in a four-cylinder automotive engine; their results are discussed.

A newly developed OHC (Over-Head Camshaft) prototype of a six-cylinder in-line diesel engine (with bore size: 114mm, stroke size: 130mm) was studied, comparing with the previous version of OHV (Over-Head Valve) type engine (with bore size: 110mm, stroke size: 130mm). It was found that the new type of cylinder block (with 130.8 kg of mass) has significantly lower natural frequencies than those for the previous type of cylinder block (with 133.2 kg of mass). Furthermore, slightly more predominant engine noise and vibration were induced in the new engine. The vibration behavior and the excitation force transmission characteristics were investigated by EMA (Experimental Modal Analysis). We performed a series of impact tests for (1) free-free cylinder block, (2) free-free crankshaft substructure with torsional damper and flywheel attached, and (3) the case where (1) and (2) are assembled together.

Hino Motors had developed an electronically controlled mechanical automatic transmission and employed it for the ′85 models of large size buses, and also ′86 models of heavy/ medium duty trucks. This system gives minimum fuel consumption and even smoother/easier driving than an automatic transmission with torque converter, by controlling an engine also with a transmission and employing an oil spray clutch. The trade name of this system is EE-Drive which means easy and economy drive.

Electronically controlled systems, originally developed for passenger cars, have been applied to trucks and buses since the early 1980's. With the increase of the objects for those applications their contents have become more and more sophisticated with rapid expansion and growth. This paper has summarized the results of observations on the background situations behind the applications of electronic control systems to trucks and buses in Japan. The status of the electronic applications, in particular to the powertrain, are explained and specific examples are provided. Future trends are also discussed.

Vehicle responsiveness to the driver's steering maneuvers and external turbulences caused by irregularities in the road surface and wind gusts are two opposing factors to be studied for better stability and controllability of vehicles. The cruising speeds of vehicles on freeways have been becoming higher, and wider physiological differences in the driving ability of drivers are appearing with the increase in elderly drivers. Therefore, to meet the requirements of higher cruising speeds and the expanding physiological differences between drivers, an electro-hydraulic feedforward control power steering system has been developed for trucks and buses. This is a parallel operating system consisting of a mechanical route and an electronic route, and improves vehicle responsiveness so as to absorb the physiological differences of drivers.

Wear resistance is the important characteristics of cast iron materials for automobile components. Because the phenomenon of wear is a highly complicated mechanism involving many factors such as surface conditions, chemical reactions with lubricants, metals, and physics, it has not been fully explained. Therefore, it will be necessary to confirm and explain the wear mechanism to develop effective improvements. The purpose of this study was to investigate the structural change behavior and effects of alloying elements when the material top surface becomes worn, in order to improve the wear resistance of cylinder liners and other cast iron materials. For this purpose, several types of prototype materials were produced, and the relationship between components and wear resistance was investigated by using a laser microscope for quantitative observation of the degree of pearlite microstructure fineness.