Search Results

The moment of inertia of the crankshaft cannot be ignored when analyzing the dynamics of a motorcycle. In this research, the tire friction force (calculated by drag and tire side force) was used as an index of the drive performance. The ratio of roll rate and steering torque (here after referred to as a roll rate gain) was used as an index of the cornering performance, and it was analyzed as the influence of the moment of inertia of a crankshaft on the drive performance as well as cornering performance. As a result, the influence on drive performance and cornering performance by the moment of inertia has been found.

This paper studies various wheel stiffness configurations, with the aim of enhancing driving stability while minimizing the increase in weight associated with an increase in stiffness. Reinforcement was added to the wheel disk and the wheel rim of standard aluminum wheels for passenger vehicles in order to produce four wheels with different stiffness configurations. The effects of disk stiffness and rim stiffness on tire contact patch profiles and driving stability were quantitatively evaluated. From the results of tests with the four wheels, it was observed that disk stiffness and rim stiffness have differing effects on tire contact patch profiles, and on driving stability. Disk stiffness influences especially tire contact patch length, and tire contact patch length influences especially maneuverability in driving stability. Rim stiffness influences especially tire contact patch area, and tire contact patch area influences especially stability in driving stability.

In motorcycles, the mass difference between a vehicle and a rider is small and motions of a rider impose a great influence on the vehicle behaviors as a consequence. Therefore, dynamic properties of motorcycles should be evaluated not merely dealing with a vehicle but considering with a man-machine system. In the studies of a simulation for vehicle dynamics, various types of rider models have been proposed and it has already been reported that rider motions have a significant influence on the dynamic properties. However, the mechanism of the interaction between a rider and a vehicle has not been clarified yet. In our study, we focused on weave motion and constructed a full vehicle simulation model that can reflect the influences of the movements of the rider’s upper body and lower body. To construct the rider model, we first measured the vibrational characteristics of a human body using a vibration test bench.

In this study, we developed a simulation method for rough road running condition to reproduce the behaviors of a vehicle body and to precisely estimate the input loads to the frame. We designed the simulation method focusing on a front fork model and a rider model optimized for this type of analysis. In the suspension model development, we conducted detailed measurement of the suspension characteristics on a test bench. Based on the yielded results, the friction force, as well as the spring reaction force and the damping force, was reproduced in the suspension model. The friction of the suspension varies depending on the magnitude of the reaction force associated with bending and this effect was also implemented in the model. Regarding the rider model, the actual behavior of a rider was investigated through the recorded motion video data and used to define the necessary degrees of freedom.

In motorcycles traveling at medium to high speed, roll stability is usually maintained by restoration forces generated by a self-steering effect. However, when the vehicle is stationary or traveling in low speed, sufficient restoring force does not occur because some of the forces, such as centrifugal force, become small. In our study, we aimed at prototyping a motorcycle having roll stability when the vehicle is stationary or at low speed with a steering control for self-standing assist, while maintaining stability properties in medium to high speed. A model was built to represent dynamics of roll motion, which is composed of a fixed point mass located above the vehicle’s center of gravity and another movable point mass below that gravity center. According to the model, when steered, the roll moment direction generated by the shift of the movable point mass becomes the same as the direction generated by the ground contact point shift of the front tire.

In order to reveal the shifting mechanisms for CVT using a metal pushing V-belt, three shifting rates were introduced. The belt motion in the pulley groove was also characterized using mean coefficients of friction as parameters, which identify the slippage condition of the belt in the pulley groove. The experimental results showed that one of shifting rates, dR/ds was almost constant in the narrowing pulley regardless of both rotational speed and transmitted torque. Here, R is the belt pitch radius in the pulley and s is the length measured along the belt pitch line. This fact indicates that the shifting is primarily governed by elastic deformation of blocks of the belt. Power transmitting states were also evaluated using a different type of lubricating oil whose nominal coefficient of friction was higher than that for the conventional AT oil. The observed mean coefficients of friction vary due to oil although the basic response of the CVT unchanged.

At present, measurements of running resistance are conducted outdoors as a matter of course. Because of this, the ambient temperature at the time of the measurements has a considerable impact on the measurement data. The research discussed in this paper focused on the temperature characteristic of the tires and developed a new correction technique using a special rolling test apparatus. Specifically, using a tire rolling test apparatus that made it possible to vary the ambient temperature, measurements were conducted while varying the levels of factors other than temperature that affect rolling resistance (load, inflation pressure, and speed). Next, a regression analysis was applied to the data for each factor, and coefficients for a relational expression were derived, making it possible to derive a quadratic equation for the tire rolling resistance correction formula.

Cabin quietness is one of the important factors for product marketability. In particular, the importance of reducing road noise is increasing in recent years. Methods that reduce acoustic sensitivity as well as those that reduce the force transferred from the suspension to the body (the suspension transfer force) are used as means of reducing road noise. Reduction of the compliance of the body suspension mounting points has been widely used as a method of reducing acoustic sensitivity. However, there were cases where even though this method reduced acoustic sensitivity, road noise did not decrease. This mechanism remained unclear. This study focused on the suspension transfer force and analyzed this mechanism of change using the transfer function synthesis method. The results showed that the balance between the body's suspension mounting points, suspension bush, and suspension arm-tip compliance is an important factor influencing the change in suspension transfer force.

The effects of aerodynamic coefficients on handling response and flat ride were quantified. For handling response, the aerodynamic effect was quantified by analysis with linear representation and a two-wheel simulation model, using aerodynamic coefficients obtained from a full scale car wind tunnel. The correlation of aerodynamic coefficients and handling response with driving feel was also ascertained. Aerodynamic yaw moment and side-force were also converted to equivalent front and rear lift to standardize aerodynamic indexes and improve aerodynamic development efficiency. For flat ride, steady and unsteady aerodynamic effects were quantified by analysis with a two-degree-of-freedom mass-spring-damper simulation model and aerodynamic coefficients obtained from a 35% scale model wind tunnel and towing tank test. Unsteady aerodynamic force occurrence mechanism was ascertained by unsteady CFD using dynamic mesh.

When fluctuations in the speed of rotation of the drive pulley are transmitted to the driven pulley via the metal V-belt, the transmitted fluctuations become attenuated as friction force approaches a state of saturation. The research discussed in this paper focused on these fluctuations in the speed of rotation and developed an index for the slip state between the belt and the pulleys. The drive and driven pulleys were regarded as a one-dimensional vibrating system connected by elastic bodies, and changes in the state matrix of the system were focused on. It was determined that when all of the eigenvalues in this state matrix become real numbers, slip speed between the belt and the pulleys increases sharply. A method was proposed of estimating this behavior of the eigenvalues from changes in the speed of rotation of the drive and driven pulleys, and indexing the current slip state.

Vehicles are required durability in various environments all over the world. Especially water resistance on flooded roads is one of the important issues. To solve this kind of problem, a CFD technology was established in order to predict the water resistance performance of the vehicle at the early development stage. By comparison with vehicle tests on flooded roads, it is clarified the following key factors are required for accurate prediction; the vehicle velocity change, the vehicle height change and the air intake flow rate. Moreover, these three key factors should be appropriately determined from vehicle and engine specification to predict water intrusion for flooded roads at the early stage of development. In this paper, a methodology which determines appropriate analysis conditions mentioned above for flooding simulation from vehicle and engine specification is described. The methodology enables us to determine whether the vehicle provides sufficient waterproofness.

The four-wheel controlling antilock brake system is considered as an effective safety device because of its capability to help a driver to maintain vehicle stability and steerability during panic braking even on a slippery road surface. This report deal with a simplified control technique which simultaneously controls right and left wheels on each front or rear axle. Both front wheels are controlled in response to a signal from the front wheel with the least slip, while both rear wheels are controlled in response to a signal from the rear wheel that has the greatest slip. A series of tests proved that this technique ensures vehicle steering ability even during panic braking. On a gravel and other rough roads, this system provided shorter stopping distance compared to other four-wheel antilock systems. It has been generally assumed that stopping distance extension on such roads is only one disadvantage of the four-wheel antilock brake system.

5 belt wind tunnels are the most common facility to conduct the experimental aerodynamics development for production cars. Among aerodynamic properties, usually drag is the most important development target, but lift force and its front/rear balance is also important for vehicle dynamics. Related to the lift measurement, it is known that the “pad correction”, the correction in the lift measurement values for the undesirable aerodynamic force acting on wheel belt surface around the tire contact patch, must be accounted. Due to the pad correction measurement difficulties, it is common to simply subtract a fixed amount of lift values from measured lift force. However, this method is obviously not perfect as the pad corrections are different for differing vehicle body shapes, aerodynamic configurations, tire sizes and shapes.

Designing a lightweight and durable engine is universally important from the standpoints of fuel economy, vehicle dynamics and cost. However, it is challenging to theoretically find an optimal solution which meets both requirements in products such as the cylinder head, to which various thermal loads and mechanical loads are simultaneously applied. In our research, we focused on “non-parametric optimization” and attempted to establish a new design approach derived from the weight reduction of a cylinder head. Our optimization process consists of topology optimization and shape optimization. In the topology optimization process, we explored an optimal structure with the theoretically-highest stiffness in the given design space. This is to provide an efficient structure for pursuing both lightweight and durable characteristics in the subsequent shape optimization process.

Predicting fuel consumption and performance of an outboard motor for a high speed small planing boat are numerically challenging. The propeller is one of the most popular propulsion systems used for outboard motors. We focused our attention on the fact that the thrust performance of a propeller has a major impact on cruising fuel consumption and performance. We believe that we can numerically predict cruising fuel consumption, which has conventionally been estimated through experiential means, using accurate thrust performance measurements via CFD simulation without cavitations model. This study aims to develop a simulator that could quantitatively predict cruising fuel consumption and performance of an outboard motor used for a high speed small planing boat. After comparing the CFD simulation of propellers against the results of model tests, the simulated results are in good agreement with the experimental results.

This paper discusses the desired steer angle characteristics of rear wheels in the new concept of four wheel steering system in which the rear wheels are controlled as a function of the steering wheel angle in a manner that the rear wheels are steered in the same direction as the front wheels when the steering wheel angle is kept within a small range while the rear wheels are steered in the opposite direction to the front in the case the steering wheel angle is steered over a larger range. This paper also indicates the basic principle of the four wheel steering system and lists items for consideration in determining the function, and then presents a variety of effects the new steering system produces on operating performances based upon a series of proving ground tests.

The change in the aerodynamic lift force (henceforth CL) by heave motion is discussed in this paper in order to clarify the effect of aerodynamic characteristics on the vehicle dynamic performance. We considered that phenomenon in actual car running at 160km/h and 1Hz heave frequency. Using a towing tank to change its water from the air to the working fluid to more easily observe this phenomenon. That makes possible to observe the same phenomenon with reduced velocity and small models under same Strouhal number condition. This method can be reducing vehicle speed to 3m/s (1/15 actual) and frequency to 0.2Hz (1/5 actual) in case using 40% scaled model. The results of these tests showed that unsteady CL is proportional to heave motion. These results showed the proportional relationship between unsteady CL and heave motion. The formularization of unsteady CL made it possible to introduce shape coefficients to vehicle dynamics simulations as functions of heave velocity.

Looking back on steering systems in more than a hundred years that have passed since the introduction of the automobile, it can be seen that original method of controlling cars pulled by animals such as horses was by reins, and early automobiles had a single push-pull bar (tiller steering). That became the steering wheel, and an indirect steering mechanism by rotating up and down caught on. While the steering wheel is the main type of steering system in use today, the team have developed the Twin Lever Steering (TLS) system controlled mainly by bi-articular muscles, making use of advancements in science and technology and bioengineering to develop based on bioengineering considerations as shown in Fig. 1. The objective of that is to establish the ultimate steering operation system for drivers. In the first report, the authors reported on results found by using race-car prototypes as shown in Fig. 2.

A multi-use road simulator for reproducing various road loads on motorcycles and buggies has been developed on a test bench by using computer-controlled hydraulic actuators. The device is controlled by a low-priced personal computer and an interface system with custom software. An unique feature is the capability to simulate loads related to such phenomena as the bottoming of suspension and the movement of a telescopic type front fork on the road.

HONDA completed research and development of the Metal V-Belt for CVTs in-house for the purpose of reducing the minimum pitch radius. The newly developed belt is essential to the compactness of a CVT and increases the speed ratio range. Increase of ring stress caused by reducing the minimum pitch radius is treated by improvement of element shape, optimizing clearance between elements and between element and ring and improving materials.(1) In this paper, the optimization of clearance between elements, heat treatment of elements and optimization of ring material are described in detail. Optimum total clearance between elements for a virgin belt is defined by test results during operation using a specially engraved gap sensor and a telemeter system. Tolerance and conditions of heat treatment for elements are optimized concerning fatigue strength of the element nose.