Search Results

At present, biodiesel fuels using natural-origin materials are expanding in share, and there are many different kinds. Biodiesel fuel generates organic acid when it deteriorates, so care is needed when evaluating the influence of the fuel on automotive fuel-line materials. A model biodiesel fuel was designed taking into account deterioration of the fuel and mixing of impurities into it. Durability of automotive fuel-line rubber and plastic materials were evaluated by using the model fuel. From the evaluation results, it was found that fluoroelastomer (hereafter referred to as FKM) and polyacetal resin (hereafter referred to as POM) deteriorate depending on specific fuel properties and deterioration state. In this paper, we report evaluating results of biodiesel fuels on the automotive fuel-line rubber and plastic materials, and the importance of biodiesel fuel property management.

Downsizing or higher compression ratio of SI engines is an appropriate way to achieve considerable improvements of part load fuel efficiency. As the compression ratio directly impacts the engine cycle thermal efficiency, it is important to increase the compression ratio in order to reduce the specific fuel consumption. However, when operating a highly boosted / downsized SI engine at full load, the actual combustion process deviates strongly from the ideal Otto cycle due to the increased effective loads requiring ignition timing delay to suppress abnormal combustion phenomena such as engine knocking. This means that for an optimal design of an SI engine between balances must be found between part load and full load operation. If the knocking characteristic can be accurately predicted beforehand when designing the combustion chamber, a reduction of design time and /or an increase in development efficiency would be possible.

A second-generation power control unit (PCU) for a two-motor hybrid system is proposed. An optimally designed power module, which is a key component of the PCU, is applied to increase heat-resistant temperature, while the basic structure of the first generation is retained and the power semiconductor chip is directly cooled from the single side. In addition to the optimum design, by decreasing the power loss as well as increasing the heat-resistant temperature of the power semiconductors (IGBT: Insulated Gate Bipolar Transistor and FWD: Free Wheeling Diode), the proposed PCU has attained 25% higher power density and 23% smaller size compared to first-generation units, maintaining PCU efficiency (fuel economy). To achieve a high yield rate in the power module assembly process, a new screening technology is adopted at the initial stage of power module manufacturing.

In recent years, the increased use of electric power steering in vehicles has increased the importance of issues such as making systems more compact and lightweight, and dealing with increased development man-hours. To increase development efficiency, the use of a “Hardware in the loop simulator” (HILS) is being tested to shift from the previous development method that relied on a driver's subjective evaluation in an actual vehicle test to bench-test development. Using HILS enables tasks such as specification studies, performance forecasts, issue identification and countermeasure proposals to be performed at an early stage of development even when there is no prototype vehicle. This report describes a case study of using HILS to solve the issues of reducing the load by adjusting the geometric specifications around the kingpin and eliminating the tradeoff by adding a new EPS control algorithm in order to make the electric power steering (EPS) more compact and lightweight.

Honda announced an independent right and left rear toe control system (first generation) in 2013 and presented it as the world's first. As stated in a previous paper, “Independent Left and Right Rear Toe Control System,” with this system Honda has achieved a balance between an enjoyable driving experience in which handling is performed at the driver's will (“INOMAMA” handling) and stable driving performance.(1) This first generation is optimally designed to the vehicle specifications such as suspension axial force and steering gear ratio of the vehicle to which the system is applied. For more widespread application of independent rear toe control technology, a next generation system (second generation) has been developed, which achieves both cost reduction and flexible system performance which can be adapted to a variety of vehicles. The system development began by setting the required target performance with consideration for adaptation to various car models.

The weight-saving requirements for automobiles are important. In order to produce a lighter engine, an aluminum block with cast-iron liners and a hypereutectic aluminum-silicon alloy block have been developed. (1)*, (2), (3), (4), (5), (6) We developed a new aluminum engine block which has the cylinder bore surface structure reinforced with short ceramic fiber. We also established technology suitable for mass-production including a fiber preform process and a non-destructive inspection method. In this paper, the optimum properties and production technology of MMC engine blocks are introduced. A portion of the paper is dedicated to the results of a comparison study between a new light-weight aluminum engine block, a hypereutectic aluminum-silicon engine block and an aluminum engine block with cast-iron liners.

The moment of inertia of the crankshaft cannot be ignored when analyzing the dynamics of a motorcycle. In this research, the tire friction force (calculated by drag and tire side force) was used as an index of the drive performance. The ratio of roll rate and steering torque (here after referred to as a roll rate gain) was used as an index of the cornering performance, and it was analyzed as the influence of the moment of inertia of a crankshaft on the drive performance as well as cornering performance. As a result, the influence on drive performance and cornering performance by the moment of inertia has been found.

The reduction of fuel consumption is of great importance to automobile manufacturers. As a prospective means to achieve fuel economy, lean burn is being investigated at various research organizations and automobile manufacturers and a number of studies on lean-burn technology have been reported to this date. This paper describes the development of a four-valve lean-burn engine; especially the improvement of the combustion, the development of an engine management system, and the achievement of vehicle test results. Major themes discussed in this paper are (1) the improvement of brake-specific fuel consumption under partial load conditions and the achievement of high output power by adopting an optimized swirl ratio and a variable-swirl system with a specially designed variable valve timing and lift mechanism, (2) the development of an air-fuel ratio control system, (3) the improvement of fuel economy as a vehicle and (4) an approach to satisfy the NOx emission standard.

We had developed Electric Servo Brake System, which can control brake pressure accurately with a DC motor according to brake pedal force. Therefore, the system attains quality brake feeling while reflecting intentions of a driver. By the way, “Build-up” is characteristics that brake effectiveness increases in accordance with the deceleration of the vehicle, which is recognized as brake feeling with a sense of relief as not to elongate an expected braking distance at a downhill road due to large-capacity brake pad such as sports car and large vehicles. Then, we have applied the optical characteristic control to every car with Electric Servo Brake System by means of brake pressure control but not brake pad. Hereby, we confirmed that the control gives a driver the sense of relief and the reduction of pedal load on the further stepping-on of the pedal. In this paper, we describe the development of brake feel based on the control overview.

In our preceding report [1], we showed that the thermal conductivity of a heat pipe dramatically improves during high-speed reciprocation. However, this cooling method has rarely been applied to car engine pistons because the thermal conductivity of commercially available heat pipes does not increase easily even if the pipe is subjected to high-speed reciprocation. In consideration of the data from our preceding report, we decided to investigate heat pipe designs for car engine pistons, propose an optimum design, and conduct thermal analysis of the design. As a result, we found that it is possible to transport heat from the central piston head area, where cooling is most needed, to the piston skirt area, suggesting the possibility of efficient cooling.

Car engine piston cooling is an important technology for improving the compression ratio and suppressing the deformation of pistons. It is well known that thermal conductivity improves dramatically through the use of heat pipes in computers and air conditioners. However, the heat pipes in general use have not been used for the cooling of engines because the flow of gas and liquid is disturbed by vibration and the thermal conductivity becomes excessively low. We therefore developed an original heat pipe and conducted an experiment to determine its heat transfer coefficient using a high-speed reciprocation testing apparatus. Although the test was based on a single heat pipe unit, we succeeded in improving the heat transfer coefficient during high-speed reciprocation by a factor of 1.6 compared to the heat transfer coefficient at standstill. This report describes the observed characteristics and the method of verification.

In recent years, increasing attention has been paid to a non-throttling technology that is expected to contribute to a reduction in fuel consumption. This paper describes a study on the technology behind the electromagnetic variable valve timing mechanism (electromagnetic valve mechanism). The electromagnetic valve mechanism ensures highly efficient and stable valve opening/closing control. The detailed information and findings will be described in the main body. In addition, the advantages of the mechanism's application to a homogeneous charge compression ignition engine (HCCI engine) will also be described.

A method for reducing friction loss in the engine timing chain was investigated using multi-body dynamics simulation. The method known as the link-by-link model was employed in the simulation to enable representation of the behavior of each single link of the chain and its friction due to contact. In order to predict the friction under actual engine operating conditions, a model that takes camshaft torque fluctuation and crankshaft rotational speed fluctuation into account was created. This simulation was used to verify the detailed distribution of friction in each part of the chain system as well as the changes of friction in the time domain. As a result, it was found that the sliding friction in the chain tensioner guide and chain guide was larger than in other locations. Based on this result, a method of reducing friction entirely by measures in mechanisms and structures without relying on low-friction materials was investigated.

The use of waste heat for automobile engine that applied Rankine cycle from the viewpoint of exergy (available energy) was researched. In order to recover heat to high quality energy, a heat-management engine whose exhaust port was replaced with an innovative evaporation device was developed. With this engine, high temperature and high pressure steam (400 degree C, 8MPa) could be generated from a large amount of the exhaust loss. In addition, high temperature water (189 degree C) was obtained from cooling loss. Consequently, the system that recovered more exergy from waste heat was established. To verify the system, the Rankine cycle system was installed in a hybrid vehicle and the automatic control system to change steam temperature and pressure according to the load variation was constructed. As the result of vehicle testing, thermal efficiency was increased from 28.9% to 32.7% (by 13.2% increase) at 100km/h constant vehicle speed.

Downsizing the engine would be an effective means of improving fuel economy and reducing CO2 emissions. In this case, low-speed torque generation can be enhanced through the use of impulse charging technology, a subject attracting the attention of many researchers. This paper reports the basic characteristics of impulse charging identified through research using a single-cylinder test engine, aiming for application of the technology to spark ignition (SI) engines. To ensure the maximum level of volumetric efficiency under impulse charging conditions, two requirements are controlling the timing of switching from a negative to a positive pressure wave while turning its direction at the intake chamber, and maximizing the positive pressure wave.

Bio-ethanol is one of the candidates for automotive alternative fuels. For reduction of carbon dioxide emissions, it is important to investigate its optimum combustion procedure. This study has explored effect of ethanol fuels on HCCI-SI hybrid combustion using dual fuel injection (DFI). Steady and transient characteristics of the HCCI-SI hybrid combustion were evaluated using a single cylinder engine and a four-cylinder engine equipped with two port injectors and a direct injector. The experimental results indicated that DFI has the potential for optimizing ignition timing of HCCI combustion and for suppressing knock in SI combustion under fixed compression ratio. The HCCI-SI hybrid combustion using DFI achieved increasing efficiency compared to conventional SI combustion.

There has been strong public demand for reduced hazardous exhaust gas emissions and improved fuel economy for automobile engines. In recent years, a number of innovative solutions that lead to a reduction in fuel consumption rate have been developed, including in-cylinder direct injection and lean burn combustion technologies, as well as an engine utilizing a large volume of exhaust gas recirculation (EGR). Furthermore, a homogeneous charge compression ignition (HCCI) engine is under development for actual application. However, one of the issues common to these technologies is less stable combustion, which causes difficulty in engine management. Additionally, it is now mandatory to provide an onboard diagnosis (OBD) system. This requires manufacturers to develop a technology that allows onboard monitoring and control of the combustion state. This paper reports on an innovative combustion diagnostic method using an in-cylinder pressure sensor.

In recent years, the contribution of tires on vehicle fuel economy has been garnering attention. Up until now, rolling resistance coefficient (RRC) has been the standard way of measuring the amount of impact the tire has on fuel economy. We devised a new method for evaluating the impact of tires on fuel economy that incorporates the concept of tire “driving transmission efficiency” (hereinafter referred to as “driving stiffness”). In doing so, we have clarified the technology direction for contributing to the improvement of fuel economy while maintaining vehicle maneuverability by reducing RRC and improving tire driving stiffness.

Formula One engines, which are the pursuit of the ultimate in performance, tend to be comparatively vulnerable to durability issues. These engines sometimes run under a state of unstable combustion as compensation for improved fuel economy. To cope with these issues, there have been strong demands in the racing field for a technology that will allow constant monitoring and prompt action to be carried out on system malfunctions and failures, as well as unstable combustion. The research program described in this paper deals with an onboard technology for monitoring combustion under all the operational conditions using ionic current measurement. The technology will possibly be applied to engine management and car-to-pit communications via telemetering. The scope of the control it offers includes; detection of misfire and hesitation, detection and management of detonation, and management of lean-burn combustion.

The mechanism of noise production in engine accessory drive belts was discussed. Applying geometric considerations to the transversal vibration of the belt, which is one cause of belt noise, the research showed that vibration of the belt is affected by fluctuations in the rotational speed of the crankshaft, and that the amplitude of the vibrations fluctuates cyclically. The cycle of this amplitude fluctuation is synchronous with engine speed, and for a 3-cylinder gasoline engine, its frequency is the (1.5*n)th engine rotation order. The spectrum pattern of belt vibration therefore shows components of the natural frequency±(1.5*n)th orders. The research demonstrated that at engine speeds at which the natural frequency±(1.5*n)th orders and the (1.5*n)th order frequencies, the engine excitation orders, are identical, multiple engine orders excite resonance in the belt, producing a high degree of belt vibration.