Search Results

In-wheel motors (IWM) will be a key technology that contributes to the popularization of electric vehicles. Combining electric drive with IWM enables both good vehicle dynamics and a roomy interior. In addition, the responsiveness of IWM is also capable of raising dynamic control performance to an even higher level. IWM enable vertical body motion control as well as direct yaw control, electric skid control, and traction control. This means that IWM can replace most control actuators used in a vehicle chassis. The most important technology for IWM is to enable the motor to coexist with the brake and the suspension arms inside the wheel. The IWM drive unit described in this paper can be installed with a front double wishbone suspension, the most difficult configuration.

Toyota Motor Corporation has developed a new six-speed automatic transmission AB60E for longitudinal front engine rear wheel drive (RWD) vehicles. This transmission development was aimed at an improvement of power performance and fuel economy, while achieving a lightweight, compact package and a high torque capacity. In order to achieve this target, a high-capacity ultra-flat torque converter, a highly-rigid transmission case, and an ATF warmer with a valve to switch ATF circuits to an air-cooled ATF cooler have been newly developed. Moreover, a new transmission mode control logic “TOW / HAUL” has been developed to improve power performance and driveability during trailer towing. This automatic transmission has adopted the same gear train and hydraulic control system as the conventional six-speed automatic transmission A760E. This paper describes the structure, major features and performance of the transmission in detail.

Toyota Motor Corporation has recently developed a new six-speed automatic transmission (A761E) for Front Engine Rear Wheel Drive (FR) vehicles. Following the general trend of increased shift stages and a wider range of gear ratios, this six-speed automatic transmission has been developed with attention paid to the gear steps and a wider range of gear ratios. By balanced selection of close-ratio gears in a wider range, the change greatly improves the power performance and fuel economy of the vehicle. To further improve fuel economy we have adopted new technologies such as low-viscosity ATF, neutral control, and deceleration control by extending the fuel cut range (reset speed). We have also adopted a flat-shaped torque converter, small solenoids, an aluminum oil pump cover, etc. to realize the lightest six-speed automatic transmission in the world.

Toyota Motor Corporation has developed a new six-speed automatic transaxle (U660E) for Front Wheel Drive (FWD) vehicles. Component parts of U660E are completely redesigned. By combining an innovative gear train which Toyota originally invented and newer technologies, U660E has achieved outstanding fuel economy, smooth and quick shift performance and quietness in a lightweight package among Automatic Transaxles (AT) with similar torque capacity.

Toyota Motor Corporation has developed a new five-speed automatic transmission (A750E/A750F) for longitudinal front engine rear wheel drive (RWD) vehicles. The development of this transmission has been aimed at improving fuel economy and power performance, achieving the world's top-level weight and compactness, while maintaining high torque capacity. In order to achieve this purpose, the gear train, torque converter, and other components are completely changed, and advanced technology has been applied. Moreover, this automatic transmission has achieved high-quality shift feel and quiet performance. This paper describes the major features and performance of this transmission in detail.

The design requirement for more efficient vehicle moves a compact car toward front wheel drive arrangement, which requires an entire redesign of its power train. Toyota, with systematic approach from its planning stage, has developed a new automatic transmission series including one 3-speed and two 4-speed transmissions. An extensive examination on gear train arrangements enabled the 3-speed light, compact and highly reliable under the arrangement of Simpson gear train, and freewheel shifts with one-way clutches at every shifting. Two different 4th gear packages with freewheel shift are combined with the 3-speed unit to provide the versatility for the 4-speed units in various installations. Besides, these transmissions feature lock-up clutch converter, oil pump of a new tooth profile and two different control systems: hydraulic and electro-hydraulic.

A new compact five-speed automatic transmission (A650E) has been developed for front engine rear wheel drive cars. The development of this transmission has been aimed at improving fuel consumption, power performance, engine noise reduction during highway cruising and smooth acceleration by employing a wide range of gearing and close gear ratios. Generally a five-speed automatic transmission is larger than a four-speed, because of additional friction elements and gears. This can result in a change in the floor panel of the car body. However, by removing a one-way clutch for second gear and employing a unique gear-train layout, this transmission has the same circumference and length as the conventional four-speed automatic transmission (A340E)(1).1 In order to reduce first or second gear noise, gear specification and supporting structures of planetary gears have been optimized by FEM analysis.

Toyota has developed the world's first 8-speed automatic transmission (AA80E) for RWD automobiles. The transmission will first be used in the all-new Lexus LS460. In addition, a novel control system has been developed to maximize the predictability, response, efficiency, and initial quality of the powertrain while utilizing the high number of gear steps.

The need for small personal mobility vehicles is growing as urbanization, the aging of society, traffic congestion, and parking become major issues, particularly in inner-city areas. The aging of society also means that more short trips within communities will be made. The i-REAL personal mobility vehicle is a next-generation single-passenger electric vehicle that enables the driver to move around town using a smaller amount of energy. This compact EV has three wheels: two front wheels driven by in-wheel motors and one rear wheel. According to the driver's needs, the i-REAL switches driving modes by changing its wheelbase. It can go slowly, allowing the driver to meet the eyes of passers-by when driving in parks, on sidewalks, or inside shopping malls. When on the road, it can lower its height and drive quickly like a bicycle or motorcycle. The body of the i-REAL leans automatically based on the speed and the turn angle to maintain the balance of the vehicle for any driver.

Aisin AW (AW) and Toyota Motor Corporation (TMC) have developed a new RWD 6 speed automatic transmission, AWR6B45(AC60), suitable for SUV’s and LDT’s in the worldwide market, not only for North America but also for other countries including emerging nations. This 6 speed automatic transmission has achieved low cost, equivalent to AW and TMCs’ current 5 speed automatic transmission, while realizing improvement in both fuel economy and driving performance against current in-house 5-speed automatic transmissions, in addition to satisfying both toughness against various usage and light weight/compactness. They are accomplished by using a compact gear train structure, the latest efficiency improvement technologies, and a high-response, compact hydraulic control system. In addition, the compactness of this 6 speed automatic transmission enables it to replace current 4 speed and 5 speed automatic transmissions for various engine applications.

Introducing all-new front wheel drive hybrid system installed in the 2016 Toyota Prius. This system was completely re-designed to maximize the potential of THS-II (Toyota Hybrid System-II). This system was designed to be able to minimize the mechanical and electrical losses from the previous generation system, improve environmental performance, and also tried to reduce size and weight. We’d like to take this opportunity to introduce the new technology of each component, and hybrid system performance.

This paper describes the development of a high performance hydraulic strut mount, which has low complex stiffness at high frequency range. To improve vehicle noise and vibration, the dynamic characteristics of the hydraulic mount were enhanced. A hydraulic chamber model was applied in the design of the strut mount which has low complex stiffness at high frequency range. A high performance hydraulic strut mount with the inner orifice is designed by applying the result of the analysis of a hydraulic chamber model and experimentally measured data. A well designed hydraulic strut mount reduces road noise for front wheel drive car.

For viscous couplings(VCs) as a driving force transmission system of vehicles, requirement of torque characteristics has been getting very stringent. Because the torque characteristics significantly affect four wheel drive vehicles' abilities such as traction performance and driving stability. Furthermore, the recent concerns on high fuel economy, low pollution and low cost require that design of VCs should be increasingly compact, light weighted and excellent in transmitted torque's stability. It is an easy way to increase viscosity of viscous coupling fluids(VCFs) for the compact design of the VC. But it might cause increase in heat load and wear of plates which resulted in degradation of the VCF. The degradation affects VCF's viscosity and impairs stability in torque transmission. Therefore it is indispensable to develop high viscosity VCF which is excellent in long-term viscosity's stability.

Aisin AW (AW) and Toyota Motor Corporation (TMC) have developed a new rear wheel drive (RWD) 10-speed automatic transmission, AWR10L65 (TMC name: AGA0), suitable for RWD/AWD luxury passenger cars and sports cars. This 10-speed automatic transmission provides enhanced drivability leading to outstanding driver satisfaction. This has been accomplished using a close ratio gear train with optimized gear steps for rhythmic shift changes and quick acceleration. Low rpm lock-up and highly responsive shift changes result in a direct shift feel. This automatic transmission contributes to improved fuel economy by having higher efficiency and lower mass than current 8-speed RWD automatic transmissions.

The authors have developed an intelligent four-wheel drive system (I-4WD) designed to distribute the driving force to the front and rear wheels at the optimum ratio according to the running condition of the vehicle. The I-4WD consists of a center differential which distributes 30 percent of the driving force to front wheels and 70 percent to rear wheels (30:70), a hydraulic multi-disk clutch, an electronic control unit and a hydraulic control circuit. The driving force distribution can be steplessly varied from 30:70 up to the rigid state by controlling the hydraulic pressure on the clutch. The main control algorithm is based on the“yaw velocity model following control.” This composition has allowed us to accurately balance the cornering performance and stability without spoiling the critical limit predictability which is that the driver knows in advance the critical limit of vehicle dynamics.

A new hybrid transmission has been developed for all-wheel-drive (AWD) cars, and is used in the new Lexus LS600h and LS600hL for its first application. It has a compact layout consisting of a power-split device, generator, high-output electric motor, and a two-stage speed reduction device. Combined with a 5-liter V-8 engine, it achieves power performance rivaling 6-liter engine vehicles, the fuel efficiency of a medium-class vehicle, and outstanding quietness. This paper describes the structure, performance, and shift control technology of this hybrid transmission.

The original Toyota Hybrid System (THS) was installed in the Prius and was introduced in 1997 as the world's first mass-produced hybrid passenger car. Since then, THS has been continuously improved. In 2003 THS-II (marketed as Hybrid Synergy Drive [HSD]), was installed in a new larger Prius. In 2006 HSD was installed in a Rear Wheel Drive Vehicle: the LEXUS GS450h. This system achieved both 4.5-liter class power performance and compact class fuel economy with outstanding emissions performance. In 2007, this system is expanded to a mechanical all-wheel-drive(AWD) in the LEXUS LS600hL(with new V8 engine). This paper will explain this hybrid system which achieved both V12 class power performance and mid-size class fuel economy, while meeting the most stringent emission standard SULEV as a full-size vehicle.

In June 2001, Toyota introduced its second hybrid vehicle to the Japanese market. It adopted a newly developed hybrid system that includes the world's first electrical four-wheel drive (4WD) system. In the development of this electrical 4WD system, it was necessary to determine the required rear motor torque to allow practical 4WD performance while maintaining excellent fuel economy. Initially, the factors affecting 4WD performance were quantitatively analyzed and then the rear wheel drive unit torque was optimized. This results in a new hybrid vehicle with practical 4WD performance and high efficiency.

Toyota Motor Corporation has developed a new super-flat torque converter for the Flex Start System. It is installed in a new six-speed automatic transaxle (U660E) for front engine, front wheel drive vehicles. The Flex Start System is the first technology in the world that can start smoothly and reduce torque converter slipping loss by using a lock-up clutch at start. The newly developed super-flat torus achieves a high torque capacity and a maximum efficiency of 90%. Fuel economy is increased further by adding an efficient damper for low-speed lock-up in the free space provided by utilizing the super-flat torus. Toyota also developed a simple and super-flat structure at the one-way clutch (O.W.C.) area. This paper describes the structure, features, and performance of this new torque converter and the Flex Start System.

A new type of torque transmit coupling has recently been developed for 4WD cars, that provides a better match to ABS, is of lighter weight, and uses a simpler operating mechanism. This coupling transmits torque with a multi-disc clutch that is engaged by the pressure of high viscosity silicone oil. The rotary blade generates variably the silicone oil pressure, according to both differential speed and direction of rotation between the front and rear wheels. This coupling provides a good match between 4WD performance and four wheel Anti-lock Braking System (ABS) by a modification of the rotary blade shape. No additional devices are needed. This paper describes the characteristics of this coupling and the in-vehicle performance.