Search Results

To comply with increasingly strict emission regulations, diesel vehicles are equipped with Diesel Particulate Filters (DPF) to capture fine particulate matter (PM) from exhaust gas. However, due to the limited capacity of DPF to capture soot, periodic regeneration processing is required to burn it off. The ash created by metal-based additives in engine oil accumulates in DPF, leading to issues such as increased regeneration frequency and decreased fuel efficiency. To solve this problem, researchers have developed diesel engine oil with reduced ash content. However, the authors are taking it a step further and developing a diesel engine oil without metal-based detergents and anti-wear additives, for even more significant environmental impact reduction. This paper describes the development of an ashless engine oil with DH-2 performance, the effects of the developed engine oil on DPF, and the results of engine and actual field tests.

Recently, deposition of ash derived from engine oil on the surface of a diesel particle filter (DPF) has been reported to worsen the performance of the DPF. It is generally known that phosphorus in engine oil is adsorbed on the surface of an automotive exhaust catalyst and reduces the performance of the catalyst. Thus, the amounts of ash and phosphorus in engine oil have been decreased. We have developed a non-phosphorus and non-ash engine oil (NPNA) that does not contain metal-based detergents and zinc dialkyldithiophosphate (ZnDTP). We performed a performance test for NPNA using an actual engine and reported that the piston detergency and anti-wear performance of NPNA were sufficiently high. However, the piston detergency of NPNA required further improvement when engine running conditions were more severe.

In order to clarify the relationship between the chemical structure of PAG (polyalkylene glycol) and the performance characteristics as the refrigeration lubricants used for HFC134a, performance tests were conducted using PAGs with different end groups and alkylene oxide chains in the presence of HFC134a. Newly developed dimethyl ether capped PAGs having more than 70 mol.% PO (propylene oxide) to less than 30 mol.% EO (ethylene oxide) as a monomer ratio were the most preferable of all PAGs tested. The refrigeration lubricants using these PAGs have been successfully introduced into the market for mobile air conditioning systems with refrigerant HFC134a.

In order to achieve the highest power output and lowest fuel consumption for the rotary engine in endurance race such as Le Mans, two types of lubricating oils were developed by conducting a single - rotor engine test at the rotational speed of 7500 rpm under full load. One was the engine oil for the lubrication of the combustion chamber. The other was a so - called system oil for lubrication of the engine system outside the combustion chamber. The conclusions obtained from the development are as follows: 1) Engine oil for the combustion chamber The engine oil greatly influences spitback phenomenon1) which can cause rotary engine trouble in an endurance race. The spitback phenomenon is decreased by the decrease of carbonaceous deposit and ash in the apex seal grooves.

Engine oils normally contain calcium detergents and ZnDTPs to have detergency and antiwear performance. However, it has been recently understood that these additives could deteriorate filter performance in catalyst and DPF. In this background this paper explains the study and the development about new type of engine oil excluding metal detergents and phosphorus compounds. The developed engine oil shows good durability in several JASO engine tests and a fleet test by formulating newly developed additives as substitute for calcium detergents and ZnDTPs.

Modern formulation in a wide variety of lubricants including engine oils and transmission fluids is designed to control friction through film-forming tribochemical reactions induced by the functional additives mixtures. Although many cases on the synergistic or antagonistic effects of additives on friction have been reported, their mechanisms are poorly understood. This study focused on the influences of metallic detergents on tribochemical reactions. We examined the mechanical properties of detergent-containing lubricants confined at a single-asperity contact and their contributions to tribochemical phenomena. We found that detergents enlarged the confinement space required for generating repulsive force and shear resistance. This means that these detergents provide steric effects under nanoconfinement at interfacial contacts.

The deposition of ash derived from engine oil on the surface of diesel particle filters (DPF) has recently been reported to degrade the performance of the DPF. It is generally known that phosphorus in engine oil is adsorbed on the surface of an automotive exhaust catalyst, reducing the performance of the catalyst. Thus, the amounts of ash and phosphorus in engine oil have been decreased. We have developed a non-phosphorus, non-ash engine oil (NPNA) that does not contain metal-based detergents or zinc dialkyldithiophosphate (ZnDTP). Various engine tests were performed, and we confirmed that under normal running conditions, the NPNA oil had a sufficiently high piston detergency and wear resistance-two important requirements for engine oil-to meet current American and Japanese standards. However, the piston detergency of NPNA required further improvement when engine running conditions were more severe.

As well as a four-wheeled vehicle, in the field of motorcycle, development of the CO2 reduction technology and practical use are required for global environment. Zinc dialkyldithiophosphate (Zn-DTP) type additives are widely used for engine oil formulations. However, phosphorus compounds are environmental load materials. The reduction of the quantity of phosphorus compounds in engine oils is required to reduce poisoning of three-way catalysts used to purify exhaust gases from internal combustion engines. Ito1) reported that they developed a sulfur-based additive as a substitute for Zn-DTP. Their non-phosphorus engine oil formulation for four-wheeled vehicles with a sulfur-based additive was examined to evaluate its anti-wear performance using the following test methods: JASO M328 for gasoline engines (KA24E) and JASO M354 for Diesel engine (4D34T4).

Just as CO2 reduction is required of four wheeled vehicles for environmental protection, similar environmental concerns drive the development of motorcycle oil technology. Zinc dialkyldithiophosphate (Zn-DTP) type additives are widely used for engine oil formulations. However, phosphorus compounds are environmental load materials. The reduction of the quantity of phosphorus compounds in engine oils is required to reduce poisoning of three-way catalysts used to purify exhaust gases from internal combustion engines. Mr. Ito and his co-authors1) reported that they developed a sulfur-based additive as a substitute for Zn-DTP. Their non-phosphorus engine oil formulation for four-wheeled vehicles with a sulfur-based additive was examined to evaluate its anti-wear performance using the following test methods:JASO M328 for gasoline engines (KA24E) and JASO M354 for Diesel engine (4D34T4).

Since construction machinery manufacturers recommend various brands and types of greases for their machinery, customers would benefit from a standardized grease which can be used in all construction machinery. Furthermore, construction machinery manufacturers have many experiences of field problems caused by commercially available and commonly used EP Lithium greases. Therefore, the Fuels and Lubricants Committee of Japan Construction Mechanization Association (JCMA) has developed a new grease specification called “Japan Construction Mechanization Association Specification (JCMAS) GK,” for construction equipment. The JCMAS GK includes requirements for National Lubrication and Grease Institute (NLGI) No. 1 and No. 2 consistency grades. The JCMAS GK greases have enough lubricating properties for periodical grease fitting of most construction machines, hydraulic excavators, bulldozers and wheel loaders. The JCMAS GK greases are applicable from -20 to +130 degrees Celsius.

Due to increasing demands for further CO2 reduction and tighter exhaust emissions regulations, automakers are increasingly downsizing turbo-charged diesel engines by raising specific power, or adopting low-pressure loop exhaust gas recirculation (LPL-EGR) systems to improve the EGR rate. However, adopting a higher boost pressure to increase the specific power, or introducing hot exhaust gas before the turbocharger compressor with the LPL-EGR system creates higher gas temperatures in the compressor, which results in soot-containing deposits derived from the engine oil in the compressor. This phenomenon causes significant deterioration of turbocharger efficiency. Therefore, countermeasures such as restricting boost pressure or limiting EGR usage in the operational map are necessary to prevent engine performance deterioration. Increasing the gas temperature in the compressor while preventing deposit formation should enable further improvements in fuel consumption and engine power.

To explore the measures that can be used to improve the fuel economy of internal combustion engines, we investigated how friction at the piston ring-cylinder liner interface is influenced by the boundary lubrication performance of engine oils. We formulated several engine oils with varying boundary lubrication performance and tested them for ring-liner friction by using a floating liner friction tester. We used friction modifiers (FMs) to modify the boundary lubrication performance of engine oils. We found that ring-liner friction is well correlated with the friction coefficients in boundary lubrication regimes when measured by a laboratory friction tester. We also found that the impact of the boundary lubrication performance of engine oils was emphasized in low viscosity engine oils. It makes it possible for improved boundary lubrication performance to inhibit or overcome the viscosity reduction-induced increase of friction energy.

Diamond-Like Carbon (DLC) is a promising engine material for reducing friction and wear on sliding parts. By contrast, MoDTC lubricant additives are known to promote the wear of a-C:H films. However, the mechanism that promotes wear and the formation of tribofilms on DLC parts when in contact with molybdenum-based lubricant additives has not been sufficiently studied. The purpose of this research is to determine the wear promotion mechanism and formation of tribofilm on DLC by lubricant additives by comparing friction and wear properties. We conducted friction and wear tests using a tribometer with DLC (ta-C, ta-C:H, a-C, and a-C:H) blocks, FC250 (cast iron) rings, and oils containing lubricant additives (MoDTC, MoDTP, and Mo without DTC ligand) by observing and analyzing the sliding surfaces of specimens. No wear was observed for any of the DLCs (ta-C, ta-C:H, a-C:H, and a-C) in combination with oils containing MoDTP or Mo without DTC ligands.

In the Japan Clean Air Program II (JCAP II) Diesel WG, effects of fuel properties on the performance of two types of diesel NOx emission aftertreatment devices, a Urea-SCR system and a NOx storage reduction (NSR) catalyst system, were examined. For a Urea-SCR system, the NOx emission reduction performance with and without an oxidation catalyst installed in front of the SCR catalyst at low exhaust gas temperature operation was compared. For an NSR catalyst system, the effect of fuel sulfur on both emissions and fuel economy during 50,000 km driving was examined. Furthermore, effects of other fuel properties such as distillation on exhaust emissions were investigated. The results show that sulfur is the influential factor for both devices. Namely, high NOx emission reduction performance of the Urea-SCR system with the oxidation catalyst at low exhaust gas temperature operation is influenced by sulfur.

Hydraulic fluid (HF) specifications for mobile construction equipment called JCMAS HK and HKB have been established by the Fuels and Lubricants Committee of Japan Construction Mechanization Association (JCMA). The specifications are designated by two viscosity categories of single grade and multigrade. Each category has ISO viscosity grade (VG) 32 and 46. The JCMAS HK oils are recommended for use in hydraulic systems designed at pressure up to 34.3MPa(5000psi) and to heat hydraulic fluid up to 100 °C. These oils also provide wear control, friction performance, oxidation and rust protection, seal swell control and filterability performance. Two piston pump test procedures were developed to evaluate lubricating performance of these oils under high pressure conditions. The JACMAS HKB oils are classified as environmentally friendly oils due to the additional requirement for biodegradability.