Search Results

THE PURPOSE of this experiment was to determine the role of residual stresses in fatigue strength independent of other factors usually involved when residual stresses are introduced. It consisted of an investigation of the influence of residual stresses introduced by shotpeening on the fatigue strength of steel (Rockwell C hardness 48) in unidirectional bending. Residual stresses were varied by peening under various conditions of applied strain. This process introduced substantially the same amount and kind of surface cold working with residual stresses varying over a wide range of values. It was found that shotpeening of steel of this hardness is beneficial primarily because of the nature of the macro-residual-stresses introduced by the process. There is no gain attributable to “strain-hardening” for this material. An effort was made to explain the results on the basis of three failure criteria: distortion energy, maximum shear stress, and maximum stress.*

The strain-life approach is now commonly used for fatigue life analysis and predictions in the ground vehicle industry. This approach requires the use of material properties obtained from strain-controlled uniaxial fatigue tests. These properties include fatigue strength coefficient (σf′), fatigue strength exponent (b), fatigue ductility coefficient (εf′), fatigue ductility exponent (c), cyclic strength coefficient (K′), and cyclic strain hardening exponent (n′). To obtain the aforementioned properties for the material, raw data from stable cyclic stress-strain loops are fitted in log-log scale. These data include total, elastic and plastic strain amplitudes, stress amplitude, and fatigue life. Values of the low cycle fatigue properties (σf′, b, εf′, c) determined from the raw data depend on the method of measurement and fitting. This paper examines the merits and influence of using different measurement and fitting methods on the obtained properties.

Magnesium alloy extrusions offer potentially more mass saving compared to magnesium castings. One of the tasks in the United States Automotive Materials Partnership (USAMP) ?Magnesium Front End Research and Development? (MFERD) project is to evaluate magnesium extrusion alloys AM30, AZ31 and AZ61 for automotive body applications. Solid and hollow sections were made by lowcost direct extrusion process. Mechanical properties in tension and compression were tested in extrusion, transverse and 45 degree directions. The tensile properties of the extrusion alloys in the extrusion direction are generally higher than those of conventional die cast alloys. However, significant tension-compression asymmetry and plastic anisotropy need to be understood and captured in the component design.

IN the first part of this paper, Mr. Halgren discusses modified 4-square testing of gears in relation to service performance, field tests, and other accelerated laboratory test methods. It contains a short description and photographs of nine different designs of modified 4-square gear testing machines now in use. Description of machines includes comments on mounting rigidity, mass-elastic system, load application, measurement and control, shut-off devices, and lubrication. Mr. Wulpi discusses single-tooth fatigue testing which is used to measure the bending strength of gear teeth. One tooth at a time is tested in the manner of a cantilever beam. By successive testing, many teeth of the same gear may be tested, and endurance limits obtained if desired. Results of these tests show that it is possible to determine clearly the effect of various metallurgical factors, such as material, heat-treatment, or surface-finishing treatment upon the bending-fatigue strength of gear teeth.

A PROGRAM was undertaken to evaluate the performance of cams and tappets as influenced by design, lubrication, and metallurgical techniques. Car and dynamometer tests and a newly developed bench test are described. The latter shows promise in lending itself to the determination of the effects of single variables in a practical, short, and economic fashion, while the former do not. For the conditions of high contact stress and boundary lubrication experienced in cam and tappet operation, the authors draw several conclusions from the test work described, categorically related to the design, lubrication, and metallurigical problems present.

INDUCTION heating, the authors show, has been successfully applied to the hardening of many types of gears. Over a million transmission gears have been produced with its aid and thousands of induction-hardened final-drive gears and pinions are giving satisfactory field service. It has resulted in lower costs (due to the substitution of carbon for alloy steel, fewer machining operations, and lower heat-treating costs) and improved quality (due to a lack of distortion and better stress distribution). The first part of this paper, by Mr. Kincaid, covers the equipment and methods used in handling various gear jobs. Then Mr. Knowlton covers the engineering tests and service performance of various types of induction-hardened gears.

Finite element analysis (FEA) predictions of magnesium beams are compared to load versus displacement test measurements. The beams are made from AM60B die castings, AM30 extrusions and AZ31 sheet. The sheet and die cast beams are built up from two top hat sections joined with toughened epoxy adhesive and structural rivets. LS-DYNA material model MAT_124 predicts the magnesium behavior over a range of strain rates and accommodates different responses in tension and compression. Material test results and FEA experience set the strain to failure limits in the FEA predictions. The boundary conditions in the FEA models closely mimic the loading and constraint conditions in the component testing. Results from quasi-static four-point bend, quasi-static axial compression and high-speed axial compression tests of magnesium beams show the beam's behavior over a range of loadings and test rates. The magnesium beams exhibit significant material cracking and splitting in all the tests.

The potential of bake hardenable steel as a substitute for SAE 1008 steel to reduce gage and improve dent resistance is investigated in this report. Outer body panels in particular are susceptible to palm printing and other forms of denting. Conventional SAE 1008 steel and a developmental continuous annealed bake hardenable steel from Inland Steel Company are compared for dent performance properties. Bake hardenable (BH) steel is a medium strength (200-350 MPa) steel that receives an increase in yield strength during the heating of the paint bake cycle. An increase in yield strength would result in an increase in dent resistance. The increase in dent resistance is more quantitatively evaluated by comparing the BH steel with the current production material (SAE 1008) of a rear compartment lid outer.

Casting, machining and structural simulations were completed on a V8 engine block made in Compacted Graphite Iron (CGI) for use in a racing application. The casting and machining simulations generated maps of predicted tensile strength and residual stress in the block. These strength and stress maps were exported to a finite element structural model of the machined part. Assembly and operating loads were applied, and stresses due to these loads were determined. High cycle fatigue analysis was completed, and three sets of safety factors were calculated using the following conditions: uniform properties and no residual stress, predicted properties and no residual stress, and predicted properties plus residual stress.

Casting technology developmentshave led to a manufacturing process that allows the casting of thin wall (2-3mm) heat resistant ferritic stainless steel exhaust manifolds which can replace stamped and tubular weldments as well as iron castings where temperature requirements are increased. This casting process combines the thin wall and clean metal benefits of the counter gravity, vacuum-assist casting process using thin, light-weight bonded sand molds supported by vacuum-ridgidized sand. This combination is called the LSVAC (Loose Sand Vacuum Assisted Casting) process, a patented process. This process will significantly contribute to the growth of near-net shape steellstainless steel castings for automotive and allied industries. For exhaust manifolds, a modified grade of ferritic stainless steel with good oxidation resistance to 950°C in high dew point synthetic exhaust gas atmospheres was developed.

Various induction hardening metallurgical variables for several induction hardening experiments in hardening gears are outlined and related to heat energy inputs and their effect on the bending fatigue strength of gears. The experiments included residual stress measurements by X-ray diffraction and by sectioning and etching techniques; bending fatigue tests; metallurgical examination comprising micro-hardness traverse tests and microstructure-macrostructure evaluations; and dimensional analysis. Based on the results obtained, it was concluded that detrimental residual tensile stresses in the fillet surface of the tooth and the presence of dark etching transformation products near the surface can affect the performance of induction hardened gears in bending fatigue, and that metallurgical requirements can be specified to improve the reliability of induction hardened gears.