Search Results

Traction control is an electronic means of reducing the wheel spin caused by the application of excessive power for the valuable grip. Wheel spin can result in loss control of the car, reduce acceleration and cause tire wear. In the front wheel tire the loss grip is experienced as underwater, where the front of the car ‘pushes’ forward, not turning as much as the driver has exposed by turning the tearing. In the rear wheels slip causing oversteer, where the rear of the car swings around, turning much sharper than the driver anticipated. The result of all these problems is that the driver starts loosing control of the vehicle, which is undesirable. With the new design of the Traction Control System, the amount of the wheel slippage is precisely controlled. In racing, this means corner can be taken constantly quicker, with system applying the maximum power possible while the driver remains in total control.

To evaluate traction and velocity performance and other operational properties of a vehicle requires data on some tire parameters including the effective rolling radius in the driven mode (no torque on a wheel), the effective radii in the drive mode (torque applied to the wheel), and also the tire longitudinal elasticity. When one evaluates vehicle performance, these parameters are extremely important for linking kinematic parameters (linear velocity and tire slip coefficient) with dynamic parameters (torque and traction net force) of a tired wheel. This paper presents an experimental method to determine the above tire parameters in laboratory facilities. The facilities include Lawrence Technological University's 4x4 vehicle dynamometer with individual control of each of the four wheels, Kistler RoaDyn® wheel force sensors that can measure three forces and three moments on a wheel, and a modern data acquisition system. The experimental data are also presented in the paper.

A study was performed to determine the effects of varying the wall thickness and material glass fiber concentration for parallel and perpendicular shrinkage rates for a constrained thin-walled box shaped component. An analysis of the shrinkage for the bottom portion of a 3 dimensional constrained thin walled injection molded component was performed using measurements made from bitmap images of the components that were obtained from a traditional flatbed scanner. The shrinkage rates were determined by comparing mold cavity hatch lines to the correlating transposed hatch lines on the plastic molded component. The perpendicular and parallel shrinkage rates were determined and are discussed as a function of thickness and glass fiber content. A wide range of processing control factors was used in the study.

A low cost fault tolerant and redundant multiplex wiring system specifically designed for automotive applications is described in this paper. Although there are many multiplex wiring systems are being used to simplify the car wiring harness, but very few are low cost, fault tolerant and redundant at the same time. Most of the system address mainly the protocol and software issues and neglected the reliability of the multiplex wiring system. This paper addresses the fault tolerant and redundancy of the system and use hardware based integrated circuit to convert from parallel to serial at the transmitter side and serial to parallel at the receiver side.

The behavior of different layer designs of a transparent armor (TA) under large strains been investigated. Impacts of light-armor piercing projectile (7.62x51AP) as influencers were tested and analyzed for predicting the TA response when the layers design angles are adjusted. The experimentation allows visualization of damage behavior and the projectile penetration. The visualization techniques are essential models for understanding the mechanisms of interaction between projectile and targeted material design. Ballistic tests results, high-speed photographs and flash-radiographs from experiments with transparent armor were used to establish LS-DYNA simulation module. Transient non-linear dynamic finite-element has been analyzed using LS-DYNA to simulate and validate the experimentation. The penetrative capability of the projectile was assessed in terms of both the ballistic limit velocity against various layer design angles of the TA and air gaps.

There are more and more LEDs being used in an automobile to replace the incandescent lamps. All those applications require high brightness LED work at high ambient temperature. However, the luminous flux output of a LED is directly related to its junction temperature. Higher the LED junction temperature, lower the luminous output from the LED. In order to efficiently apply LED to an automotive application the temperature effects on luminous flux must be accounted for in any design of a LED assembly. A LED junction temperature measurement system is described in this paper to measure the differential junction temperature between a reference LED and the LED under test. And the results are used to improve the LED assembly design.

A new inter-disciplinary degree program has been developed at Lawrence Technological University: the Master of Science in Mechatronic Systems Engineering Degree (MS/MSE). It is one of a few MS-programs in mechatronics in the U.S.A. today. This inter-disciplinary program reflects the main areas of ground vehicle mechatronic systems and robotics. This paper presents areas of scientific and technological principles which the Mechanical Engineering, Electrical and Computer Engineering, and Math and Computer Science Departments bring to Mechatronic Systems Engineering and the new degree program. New foundations that make the basis for the program are discussed. One of the biggest challenges was developing foundations for mechanical engineering in mechatronic systems design and teaching them to engineers who have different professional backgrounds. The authors first developed new approaches and principles to designing mechanical subsystems as components of mechatronic systems.

The experimental methods focused on utilizing the newly developed NOVA induction heating and hardening manufacturing process as an adapted method to produce high performance engine valve springs. A detailed testing plan was used to evaluate the expected and theorized possibility for fatigue life enhancement. An industry standard statistical analysis method and tools were employed to objectively substantiate the findings. Fatigue cycle testing using NOVA induction-hardened racing valve springs made of ultra-high tensile material were compared to data for springs with traditional heat treatment and those with standard processing. The results were displayed using Wöhler and modified Haigh fatigue life diagrams. The final analysis suggests that NOVA processed springs have a seemingly slight, yet significant benefit in fatigue life of 5 - 7% over springs processed through a competing method.

The initiative of this paper is focused on improving the heat dissipation from the pressure wheel of a laser welding assembly in order to achieve a longer period of use. The work examines the effects of different geometrical designs on the thermal performance of pressure wheel assembly during a period of cooling time. Three disc designs were manufactured for testing: Design 1 – a plain wheel, Design 2 – a pierced wheel, and Design 3 – a wheel with ventilating vanes. All of the wheels were made of carbon steel. The transient thermal reaction were compared. The experimental results indicate that the ventilated wheel cools down faster with the convection in the ventilated channels, while the solid plain wheel continues to possess higher temperatures. A comparison among the three different designs indicates that the Design 3 has the best cooling performance.

A vehicle-level data acquisition (DAQ) system was developed and implemented on the Lawrence Technological University (LTU) Baja SAE vehicle. This low-cost Arduino-based DAQ system is capable of accurately and repeatedly measuring Baja SAE specific vehicle parameters and storing them for offline analysis. While expandable for the needs of future teams, the developed DAQ system includes measurement of vehicle wheel speed, CVT pulley speeds, suspension position, CVT belt temperature, steering load, and steering angle. The development of the DAQ system architecture and the development of the angular speed and suspension position measurement subsystems are the focus of this work. The processes followed and lessons learned can be used by other Baja SAE and SAE Collegiate Design Series. Each measurement subsystem was designed, fabricated, integrated, and validated on the bench and in-vehicle.

The 1999 Lawrence Technological University (LTU) drive train consists of a sprocket and chain assembly that delivers the torque, developed by a 600cc Honda F3 engine, to the rear wheels. The torque is transferred through a limited-slip, torque sensing differential unit comprised of a gear set in a student designed housing. The 1999 differential is a second-generation aluminum housing. The idea of using aluminum was first attempted with the 1998 team who successfully completed and used aluminum despite much complexity and a few design flaws. Therefore, in the LTU Formula Team's continuing effort to optimize the design, a new less complex design was conceived to house the gear set. This innovative design reduces the number of housing components from three in 1998, to two in 1999.

This paper reviews how sound transmission loss (STL) of insulators is affected by gravitational and thermal effects. A special STL test fixture was designed and fabricated to quickly and accurately obtain the STL measurement of a sample oriented at various controlled angles. The STL apparatus was designed to roll into a large reverberation chamber and act as the anechoic termination for a two-microphone approach to measuring STL. The fixture was also built with the intention of studying the temperature effects on a material's STL performance. A variety of samples, including lightweight and traditional barrier decoupled insulators, were tested in the horizontal, vertical, and inverted positions to evaluate gravitational/inertial effects. Thermal effects were investigated by bringing the STL apparatus and sample to a low temperature by moving outdoors, and then rolling the system into the reverberation chamber, at normal room temperature.

AASHTO I-Beam is a standard structural concrete part for bridge sections. The flexural performance of an AASHTO I-Beam is critical for bridge design. This paper presents an application of Digital Image Correlation (DIC) Method in full-scale AASHTO I-Beam flexural performance study. A full-scale AASHTO I-Beam pre-stressed with steel strands is tested by three-point bending method. The full-scale AASHTO I-Beam is first loaded from 0 kips to 100 kips and is then released from 100 kips to 0 kips. A dual-camera 3D Digital Image Correlation (DIC) system is used to measure the deflection and strain distribution during the testing. From the DIC results, the micro-crack generation progress during the loading progress can be observed clearly from the measured DIC strain map. To enable such a large-scale DIC measurement, the used DIC setup is optimized in terms of the optical imaging system and speckle pattern size.

The 2000 Formula SAE Team at Lawrence Technological University (LTU) has designed a chain driven, three-piece aluminum differential unique from past years. This innovative design introduces an adjustable chain mount replacing conventional shackles. Made completely of aluminum, this device moves the entire rear drive train. The gear set remains to be limited slip with a student designed housing. The idea of an aluminum housing with manufactured gear set is a continued project at LTU. After cutting approximately 33% from the weight of the 1999 differential, the 2000 is geared toward a simpler, and smaller design, easier assembly and lighter weight. After reading this brief overview, the idea of this paper is to provide an understanding of the reasoning behind the choices made on the LTU driveline team. FIGURE 1

All-wheel driveline systems with electronic torque control on each and all wheels, torque vectoring and torque management devices, hybrid electro-mechanical systems, and individual electro (hydraulic) motors in the wheels have been gaining a bigger interest in the industry for recent years. The majority of automotive applications are in vehicle stability control that is performed by controlling the vehicle yaw moment. Some devices also improve vehicle traction performance. The proposed paper develops a methodology that includes the key-principles in all-wheel driveline systems design and is based on the wheel power management as a broader analytical approach. The proposed principles relate to the optimization of power distributions to the drive wheels in both rectilinear and curvilinear vehicle motion. Inverse dynamics is the basis for the developed methodology.

All-wheel drive (AWD) vehicle performance considerably depends not only on total power amount needed for the vehicle motion in the given road/off-road conditions but also on the total power distribution among the drive wheels. In turn, this distribution is largely determined by the driveline system and its mechanisms installed in power dividing units. They are interwheel, interaxle reduction gears, and transfer cases. The paper presents analytical methods to evaluate the energy and, accordingly, fuel efficiency of vehicles with any arbitrary number of the drive wheels. The methods are based on vehicle power balance equations analysis and give formulas that functionally link the wheel circumferential forces with slip coefficients and other forces acting onto an AWD vehicle. The proposed methods take into consideration operational modes of vehicles that are tractive mode, load transportation, or a combination of both.

Online road profiling capability is required for automotive active suspension systems to be realized in a commercial landscape. The challenges that impede the realization of these systems include a profiler’s ability to maintain an optimal resolution of the oncoming road profile (spatial frequency). Shifting of the profile measurement frame of reference due to body motion disturbances experienced by the vehicle also negatively impacts profiling capability. This work details the early development of a corrective look-ahead road profiling system (CLARPS) and its control logic. The CLARPS components are introduced and additional focus will be given to the development of the angle generating function (AGF) and how it drives the ability of the system to optimize look-ahead viewing angles for the best spatial frequency resolution of a road profile. The CLARPS simulation environment is demonstrated with numerical comparison of simulated road profiles at varying vehicle speeds.

In this paper, a reconfigurable object-oriented simulator is proposed to analyze the performance of Bluetooth Voice Communication Package (VCP) for telecom purposes like hands-free vehicular communication. It consists of a graphical user interface (GUI) for research or validation engineers to investigate system specific performance. For example, a research engineer can utilize this GUI to analyze a system performance using different noise reduction filtering techniques in vehicular hands-free applications. Also, a validation engineer can utilize this GUI to evaluate vehicular Bluetooth audio quality for different vehicles at different driving conditions (e.g. speeds, fan levels, etc.). The proposed Bluetooth VCP model consists of modules like Audio Equalization (EQ), Acoustic Echo Canceller (AEC), and Noise Suppression (NS). This dynamic GUI platform provides the scope to add and analyze new proposed filtering techniques.