Search Results

A traction test machine, developed for evaluation of traction-CVT fluids for the automotive consortium, USCAR, provides precision traction measurements to stresses up to 4 GPa. The high stress machine, WAMhs, provides an elliptical contact between AISI 52100 steel roller and disc specimens. Machine stiffness and positioning technology offer precision control of linear slip, sideslip and spin. A USCAR traction test methodology includes entrainment velocities from 2 to 10 m/sec and temperatures from -20°C to 140°C. The purpose of the USCAR machine and test methodology is to encourage traction fluid development and to establish a common testing approach for fluid qualification. The machine utilizes custom software, which provides flexibility to conduct comprehensive traction fluid evaluations.

Accurate motion prediction can be used to evaluate vibrations at seat track and steering wheel. This paper presents the prediction and correlation of truck frame motion from wheel force transducer (WFT) measurements. It is assumed that the method can be used to predict vibrations at seat track and steering wheel for unibody vehicles. Two durability events were used for calculation. WFT measurements were used as inputs applied on frame from suspension. Frame loads were then used as inputs to calculate frame motions using a FEA approach. The predicted frame motions are represented by four exhaust hangers and they are compared with measured motions of the same locations. The correlations include displacement, velocity, and acceleration. It is shown that good correlations are obtained in velocity and displacement. Acceleration shows bigger differences than velocity and displacement.

In this study, multi-planar Nearfield Acoustical Holography (NAH) is used to investigate noise radiated from the front, side and rear areas of single tires on a two-wheel trailer. Contributions to the radiated noise from the leading edge, trailing edge, and sidewall of the tire are identified. Two tires - an experimental monopitch tire and a production passenger car tire - are evaluated on a smooth asphalt pavement at 58 km/hr. From the measured complex pressure, acoustic intensity is reconstructed on three planes surrounding the tire using modified NAH procedures. Additionally, sound power levels are presented in tabulated and spectra forms. Tire noise generating mechanisms are inferred based on the results.

Historically, vehicle fluid condition has been monitored by measuring miles driven or hours operated. Many current vehicles have more sophisticated monitoring methods that use additional variables such as fuel consumption, engine temperature and engine revolutions to predict fluid condition. None of these monitoring means, however, actually measures a fluid property to determine condition, and that is about to change. New sensors and diagnostic systems are being developed that allow real time measurement of some lubricant physical and/or chemical properties and interpret the results in order to recommend oil change intervals and maximize performance. Many of these new sensors use electrochemical or acoustic wave technologies. This paper examines the use of these two technologies to determine engine oil condition and focuses on the effects of lubricant chemistry on interpreting the results.

The work presented here is the second of two papers investigating the KA24E engine test. The first paper characterized the KA24E engine in terms of the physical and chemical operating environment it presents to lubricants. The authors investigated oil degradation and wear mechanisms, and examined the differences between the KA24E and the Sequence VE engine tests. It was shown that while the KA24E does not degrade the lubricant to the extent that occurs in the Sequence VE, wear could be a serious problem if oils are poorly formulated. This second paper examines the wear response of the KA24E to formulation variables. A statistically designed matrix demonstrated that the KA24E is sensitive to levels of secondary zinc dialkyldithiophosphate (ZDP), dispersant and calcium sulfonate detergent. This matrix also showed that the KA24E appears to have good repeatability for well formulated oils and is a reasonable replacement for the wear component of the Sequence VE.

The Nissan KA24E engine test is designated to replace the Ford Sequence VE engine test as the low temperature valve train wear requirement for ILSAC (International Lubricant Standardization and Approval Committee) GF-3. The KA24E (recently designated the Sequence IV A) represents much of the current world-wide material and design technology while retaining the sliding cam/follower contact found in earlier engine designs. The work presented here is the first of two reports. In this first report, the physical and chemical environment the KA24E engine presents a lubricant is characterized and compared to those of the Sequence VE engine. Valve train materials and wear modes are investigated and described. Although chemical analysis of drain oils indicate the KA24E procedure does not degrade the lubricant to the extent seen in the Sequence VE test, valve train wear appears to proceed in a similar manner in both tests.

Throughout the evolution of the automobile, passenger car motor oils have been developed to address issues of wear, corrosion, deposit formation, friction, and viscosity stability. As a result, the internal combustion engines are now developed with the expectation that the lubricants to be used in them will deliver certain performance attributes. Metallurgies, clearances, and built-in stresses are all chosen with certain expectations from the lubricant. A family of chemicals that has been universally used in formulating passenger car motor oils is zinc dithiophosphates (ZDPs). ZDPs are extremely effective at protecting highly stressed valve train components against wear failure, especially in engine designs with a sliding contact between cams and followers. While ZDPs' benefits on wear control are universally accepted, ZDPs have been identified as the source of phosphorus, which deactivates noble metal aftertreatment systems.

The potential for catalytically enhanced ignition in low-heat rejection Diesel engines has been experimentally studied under engine simulated conditions in a high pressure chemical flow reactor. Results are presented for propane oxidation on platinum at 6 and 10 atmospheres, at temperatures from 800K to 1050K, and at equivalence ratios from 0.5 to 4.0. For turbulent transport rates which are typical of those in an engine, as much as 20% of the fuel was found to react on the catalyst before the onset of the gas-phase ignition reactions. Depending on the adiabaticity of the combustion chamber walls, this could lead to significant thermal enhancement of the gas-phase ignition process. Evidence of chemical enhancement was also observed, at 10 atm under very fuel rich conditions, in terms of a change in the concentration and distribution of the hydrocarbon intermediate species. Possible mechanisms for the observed chemical enhancement due to surface generated species are discussed.

This study describes the use of Quantitative Structure Activity Relationships (QSAR) to develop predictive models for non-acidic Lubricity agents. The work demonstrates the importance of separating certain chemical families to give better and more robust equations rather than grouping a whole data set together. These models can then be used as important tools in further development work by predicting activities of new compounds before actual synthesis/testing.

Over 250 million tires are scrapped in the United States each year. Tires have been a problematic scrap because they have been designed to resist destruction, and have a tendency to float upwards in landfills. Improper storage has resulted in tire fires1--an even more problematic environmental concern than unsightly piles which can serve as breeding grounds for insect vectors. A better solution is to recover materials for use in new components. Not only does this resolve the landfill issue, but it also serves to conserve resources, while returning an economic benefit to society. This paper traces the introduction of tire material recovery at NRI Industries and DaimlerChrysler Corporation (DCC), the development of the infrastructure and materials, and the launch of the Jeep Grand Cherokee thermoplastic elastomer (TPE) radiator seals, comprised of post consumer tire crumb.

In this paper, a comprehensive evaluation index for impact harshness (IH) is proposed. A mid-sized uni-body SUV is selected for this study, with the acceleration responses at the various vehicle body locations as objective functions. A sensitivity study is conducted using an ADAMS full vehicle model with flexible body structure representation over an IH event to analyze the influence of various suspension tuning parameters, including suspension springs, shock damping, steer gear ratio, unsprung mass, track-width, and bushing stiffness.

Current phase of the study was undertaken to examine tensile fatigue behavior of cord-rubber composites representing bias tire carcass under various frequencies up to the level which closely simulates loading during high-speed take-off of aircraft. At a given stress amplitude, the use of higher cyclic frequency was found to affect strain response and heat build-up characteristics of composites significantly. The lower level of initial strain observed at higher frequency stems clearly from strain rate dependence of deformation of rubber matrix composites. The temperature profile of the specimens subjected from 20 to 30 Hz loading showed that hysteretic heating under these conditions may lead to thermal fatigue failure as well as chemical degradation influencing both fiber-matrix adhesion strength and matrix strength.

Brake judder, which is a low frequency excitation of the suspension and thus, the body structure during low-G braking, is mainly felt at the steering wheel and throughout the vehicle structure. Brake judder is a problem that costs manufacturers millions of dollars in warranty cost and undesirable trade offs. The magnitude of judder response depends not only on the brake torque variation, but also on the suspension design character-istics. This paper discusses the judder simulation process using ADAMS software to investigate the suspension design sensitivity to the first order brake judder performance. The paper recommends “tuning knobs” to suspension designers and vehicle development engineers to resolve issues in the design and development stages. Various suspension design varia-bles including geometry and compliances as well as brake related characteristics were investigated.

In this study, a full vehicle with durability tire model established with ADAMS is applied to simulate the dynamic behavior of the vehicle under severe rough road proving ground events, where the shock force-velocity characteristics are modeled as nonlinear curves and multi-stage representations, respectively. The shock forces and velocities at each corner are resolved and through full factorial DOE, the shock forces and velocities response surface models are established to analyze the sensitivities of shock force and velocity to the shock damping characteristics.

New technologies are being commercialized across the automotive industry to address demands for improved fuel economy, emissions reductions, and improved customer satisfaction. Push-belt continuously variable transmissions (b-CVTs) are beginning to command a significant percentage of the market now dominated by manual and conventional automatic transmissions. In addition, automobile manufacturers plan to introduce the first traction drive toroidal-CVTs to the market place within the next five years. A review of the relative benefits and limitations of each of these automatic transmissions exists in the literature. In this paper we consider how the performance requirements of each of these automatic transmission systems impact automatic transmission fluid technology. The physical characteristics and screen test performance of two commercial ATFs, a b-CVTF, and two traction fluids were examined.

In this paper, we study the sensitivity of a vehicle impact harshness (IH) performance to the suspension bushing rates. A mid-sized uni-body SUV is selected for this study, with the acceleration responses at the driver seat track and the steering wheel as objective functions. A sensitivity study is conducted using an ADAMS full vehicle model including a tire model and flexible body structure representation over an IH event. The study resulted in the identification of key bushings that affect the IH performance and its sensitivity to the bushing rates. Based on the results, we came-up with an “optimal” bushing set that minimizes impact harshness, which was subjectively verified to result in significant improvement in IH.

In automotive testing, a chassis dynamometer is typically used, during cell testing, to evaluate vehicle performance by simulating actual driving conditions. The use of indoor cell testing has the advantage of running controlled tests where the cell temperature and humidity and solar loads can be well controlled. Driving conditions such as vehicle speed, wind speed and grade can be also controlled. Thus, repeated tests can be conducted with minimum test variations. The tractive effort required at the wheels of a vehicle for a given set of operating parameters is determined by taking into account a set of variables which affect vehicle performance. The forces considered in determination of the tractive effort include the constant friction force, variable friction force due to mechanical and tire friction, forces due to inertia and forces due to aerodynamic and wind effects. In addition, forces due to gravity are considered when road grades are simulated.

The oxidation of 1-butene and n-butane in air at elevated pressure was investigated in a high pressure chemical flow reactor. Results are presented for pressures of 3, 6, and 10 atm, temperatures near 900K, and lean equivalence ratio. Gas samples were analyzed using gas chromatography with aldehydes sampled using a dinitrophenylhydrazine/acetonitrile procedure employing gas chromatography/mass spectrometry analysis. Major common products observed include CO, CH2O, C2H4, C3H6, and CO2. Additional major products included 1,3-C4H6 for 1-butene and 1-C4H8 for n-butane. Fuel conversion was increased with increased pressure, temperature, and equivalence ratio with 1-butene more reactive than n-butane. Large levels of lower molecular weight carbonyls resulted from 1-butene whereas significant amounts of conjugate and lower molecular weight alkenes resulted from n-butane. Trends in product distributions with increasing pressure were successfully accounted for by current autoignition theories.

An advancement in traction control has entered the marketplace this year with the debut of the 1999 Jeep® Grand Cherokee equipped with the Quadra-TracII or Quadra-Drive four wheel drive systems. The new technology that is at the heart of these systems is the progressive coupling. A new passive adaptive traction control device that utilizes much of the hardware normally associated with automatic transmissions but applied to enhance traction. In the following report the function of progressive coupling will be described along with design characteristics and parameter recommendations.

Accurate finite element model of a structure is required in order to carry out its dynamic design at the computer level. It has been observed that due to various approximations made in the Finite Element model the predicted values of the dynamic characteristics quite often differs from that of the actual structure. In view of this, the FE model is updated in the light of the test data from Experimental modal analysis (EMA) so as to improve its correlation with the test data. In this paper updating of a FE model of a two wheeler chassis structure is presented. Chassis is considered in the assembled condition with engine, suspension and tires. First an approximate FE model is constructed followed by modal analysis on the structure. FE Model updating is then carried out using Inverse Eigen sensitivity Method. Updated model predictions are found to resemble closely with the experimental results.