Search Results

The strong focus on reducing brake drag, driven by a historic ramp-up in global fuel economy and carbon emissions standards, has led to renewed research on brake caliper drag behaviors and how to measure them. However, with the increased knowledge of the range of drag behaviors that a caliper can exhibit comes a particularly vexing problem - how should this complex range of behaviors be represented in the overall road load of the vehicle? What conditions are encountered during coastdown and fuel economy testing, and how should brake drag be measured and represented in these conditions? With the Environmental Protection Agency (amongst other regulating agencies around the world) conducting audit testing, and the requirement that published road load values be repeatable within a specified range during these audits, the importance of answering these questions accurately is elevated. This paper studies these questions, and even offers methodology for addressing them.

This paper presents a vehicle dynamic simulation using a finite element method for performing more accurate simulations under extreme operating conditions with large tire deformation. A new hourglass control scheme implemented in an explicit finite element analysis code LS-DYNA(1) is used to stabilize tire deformation. The tires and suspension systems are fully modeled using finite elements and are connected to a rigid body that represents the whole vehicle body as well as the engine, drive train system and all other interior parts. This model is used to perform cornering and braking behavior simulations and the results are compared with experimental data. In the cornering behavior simulation, the calculated lateral acceleration and yaw rate at the vehicle's center of gravity agree well with the experimental results. Their nonlinear behavior is also well expressed.

The Corrosion Task Force of the Automotive/Steel Partnership has developed the SAE J2334 cyclic laboratory test for evaluating the cosmetic corrosion resistance of auto body steel sheet. [Ref. 1] Since the publishing of this test in 1997, further work has improved the precision of J2334. In this paper, the results of this work along with the revisions to the J2334 test will be discussed.

This paper describes a system for measuring unsteady pressure at up to 256 spatial points and at frequencies up to 300 Hz. The system consists of commercially available equipment for measuring steady pressures. It is based on the use of electronically scanned pressure (ESP) sensors, 16 A/D converters, and a personal computer to control the whole system and acquire data. The signal outputs through the tubes connecting the pressure taps and the ESP sensors are compensated, as are the phase delays between the scanned signals and the gain variation. A 1/5 scale model of a sedan was used in this experiment. The passenger car model was placed in a wind tunnel equipped with a moving belt, which was operated at the same speed as the uniform flow in the wind tunnel. Pressure measurements were obtained at 252 points in a plane behind the model perpendicular to the uniform flow. Measurements were made with the belt turned on and off.

Three-dimensional computation has been applied to analyze combustion and emission characteristics in direct-injection diesel engines. A computational code called TurboKIVA was used to investigate the effects of the swirl ratio, one of the fundamental factors related to combustion control, on combustion characteristics and NOx and soot emissions. The code was first modified to calculate soot formation and oxidation and the precise behavior of fuel drops on the combustion chamber wall. As a result of improving calculation accuracy, good agreement was obtained between the measured and predicted pressure, heat release rate and NOx and soot emissions. Using this modified version of TurboKIVA, the effects of the swirl ratio on NOx and soot emissions were investigated. The computational results showed that soot emissions were reduced with a higher swirl ratio. However, a further increase in the swirl ratio produced greater soot emissions.

Nissan’s new 2.8 liter in-line 6-cylinder turbocharged engine was developed for Che Datsun 280ZX in order to achieve higher performance and improved fuel economy. The Electronic Concentrated Engine Control System (ECCS), controlled by microprocessor, is provided for this 2.8 liter turbocharged engine. ECCS controls fuel injection, ignition timing, EGR rate and idling speed. It solved the problems related to power and fuel economy by optimizing the control parameters. Further, this system contains a barometric pressure compensator and a detonation controller; thus, the performance of this engine is efficient over a wide range of circumstances and fuel octane ratings. During the development of the engine, computer simulation was employed to predict engine performance and select turbocharger size, valve timing and other important factors.

This paper describes the development of a vehicle with four-wheel steering in which the rear wheels can be controlled electronically in addition to the conventional front-wheel steering system. In the method for steering the rear wheels, the side-slip angle at the vehicle's center of gravity is maintained at zero, which improves the basic dynamic properties of the vehicle. This approach allows greater maneuverability at low speed by means of counter-phase rear steering and improved stability at high speed through same-phase rear steering. However, the use of counter-phase rear steering to improve maneuverability gives rise to problems in regard to practicality. In addition, continuously controlled four-wheel steering, using counter-phase at low speed and same-phase at high speed, leads to many other problems regarding practicality because of the strong apparent understeer characteristics.

Nissan has developed a second generation ceramic turbocharger rotor which provides greater reliability and higher performance than a conventional ceramic rotor. The new rotor is made of silicon nitride, which has demonstrated sufficient strength in vehicle applications. The bonding technique for joining the ceramic rotor to the metal shaft has been confirmed through experimentation to have sufficient reliability. The second generation rotor is featured by the low stress design and higher dynamic strength, and two factors contribute to its higher reliability. The rotor shape was optimized on the basis of results obtained in two analyses of particle impact resistance and applied combined stress. Test results show that the reliability of the second generation rotor have been substantially improved over those of the conventional rotor now being used on production vehicles.

Electric Vehicle distinctive techniques in order to enhance the vehicle dynamic performance have been studied and applied to Nissan LEAF. From the viewpoint of performance design parameters, this paper introduces the application items focusing on effectuality for the vehicle behavior by means of the yawing motion and the rolling motion control of its vehicle. As the result, the effects of vehicle performance are shown in experimental data.

This paper reports about a trial for miniaturization of an air-cooled inverter integrated with motor, which is realized by reduction of the total volume of smoothing capacitor. An integrated system prototype was constructed with a disk-shaped inverter positioned at the rear end of the motor. We examined the possibility of using a ceramic capacitor, which features a higher heat-resistance temperature, lower internal resistance and higher capacity density than a film capacitor. At the same level of capacitance, the volume of a ceramic capacitor is less than one-half that of a film capacitor, enabling the size of the smoothing capacitor to be reduced to approximately one-fifth that of the currently used device. A suitable circuit configuration and physical layout of distributed smoothing capacitors and corresponding power device modules are proposed and demonstrated.

In Biodiesel Fuel Research Working Group(WG) of Japan Auto-Oil Program(JATOP), some impacts of high biodiesel blends have been investigated from the viewpoints of fuel properties, stability, emissions, exhaust aftertreatment systems, cold driveability, mixing in engine oils, durability/reliability and so on. This report is designed to determine how high biodiesel blends affect oil quality through testing on 2005 regulations engines with DPFs. When blends of 10-20% rapeseed methyl ester (RME) with diesel fuel are employed with 10W-30 engine oil, the oil change interval is reduced to about a half due to a drop in oil pressure. The oil pressure drop occurs because of the reduced kinematic viscosity of engine oil, which resulting from dilution of poorly evaporated RME with engine oil and its accumulation, however, leading to increased wear of piston top rings and cylinder liners.

The global market pressure of requiring high quality vehicles at lower prices has forced automotive manufacturers to change the way they engineer their products. In the electrical/electronic part of the automobile business, a strategy of reusing common hardware and software components was needed to support these market pressures. The General Motors strategy was to develop a standard electrical architecture. This paper will identify what a standard electrical architecture is, how a standard electrical architecture helps General Motors meet market demands, and issues that General Motors encountered in trying to implement this standard electrical architecture.

This paper presents a new measurement technique for in-cylinder gas temperature and residual gas concentration during the compression stroke of an internal combustion (IC) engine. This technique is based on the infrared absorption of water vapor by a wavelength modulated laser. Wavelength modulation spectroscopy with second harmonic detection (WMS-2f) was adopted to enable the short-path measurements over a wide range of temperatures and pressures corresponding to the late compression stroke in a typical automotive engine. The WMS-2f signal is detected through a bandpass filter at a width of 7.5 kHz, enabling crank angle-resolved measurements. The temperature is determined from the ratio of optical absorption for two overtone transitions of water vapor in the intake gas mixture, and the H2O concentration is determined from this inferred temperature and the absorption for one of the transitions.

A computer assisted development technique for Quick Plastic Forming parts [1] is described, based on the simulation program PAM-STAMP [2]. The technique allows thickness changes during forming to be accurately considered in the development process without physical trials. Process pressure cycles, which provide for maximal material formability, can be determined with a single simulation. The paper describes new program features, which reduce modeling effort and increase simulation accuracy. Various validation examples and industrial case studies are also presented, demonstrating current capabilities.

This paper presents the technologies incorporated in an electric vehicle (EV)/hybrid electric vehicle (HEV) inverter built with power semiconductors of silicon carbide (SiC) metal-oxide-semiconductor field-effect transistors (MOSFETs) instead of conventional silicon (Si) insulated gate bipolar transistors (IGBTs). A SiC inverter prototype of 2.9 L in size for driving an 80-kW motor was fabricated and evaluated on a motor test bench. The SiC inverter prototype attained average efficiency of 98.5% in the Worldwide harmonized Light-duty Test Cycle (WLTC) driving mode. The two main technologies achieved with this SiC inverter prototype are described. The first one is a new direct-cooled power module with a thick copper (Cu) heat spreader located under the semiconductors that improves thermal resistance by 34% compared with a conventional direct-cooled power module.

Road Noise is generated by the change of random displacement input inside the tire contact patch. Since the existing 3 or 6 directional electromagnetic shakers have a flat surface at the tire contact patch, these shakers cannot excite the vehicle in a manner representative of actual on-road road noise input. Therefore, this paper proposes a new experimental method to measure the road noise vehicle transfer function. This method is based on the reciprocity between the tire contact patch and the driver's ear location. The reaction force sensor of the tire contact patch is newly developed for the reciprocal loud speaker excitation at the passenger ear location. In addition, with this equipment, it is possible to extract the dominant structural mode shapes creating high sound pressure in the automotive interior acoustic field. This method is referred to as experimental structure mode participation to the noise of the acoustic field in the vibro-acoustic coupling analysis.

In racetrack conditions, brake systems are subjected to extreme energy loads and energy load distributions. This can lead to very high friction surface temperatures, especially on the brake corner that operates, for a given track, with the most available traction and the highest energy loading. Individual brake corners can be stressed to the point of extreme fade and lining wear, and the resultant degradation in brake corner performance can affect the performance of the entire brake system, causing significant changes in pedal feel, brake balance, and brake lining life. It is therefore important in high performance brake system design to ensure favorable operating conditions for the selected brake corner components under the full range of conditions that the intended vehicle application will place them under. To address this task in an early design stage, it is helpful to use brake system modeling tools to analyze system performance.

In today’s highly competitive automotive environment people are always looking to develop processes that are fast, efficient, and effective. Moving testing from expensive prototype vehicles into the laboratory is an approach being implemented for many different vehicle subsystems. Specifically a process has recently been developed at General Motors that predicts exhaust back pressure performance for a running vehicle using laboratory testing and spreadsheet calculations. This paper describes the laboratory facility and procedure, the theory behind the calculations, and the correlation between vehicle test and laboratory based results. It also comments on the benefits of the process with respect to reduction in design iterations, quicker availability of results, and money savings.

The optimal selection of vehicle body and powertrain mounts from “mount libraries” is one of the major undertakings to achieve optimal vehicle dynamics and N&V performance through the reuse of existing mount designs. The great challenges of the process are due to the facts that conventional optimization procedures, either through simulation or DOE, can not be used directly because the stiffness rates of the mounts are scattered and bundled. Sorting out the best through hardware tests is generally unrealistic simply due to the huge number of mount combinations. This paper presents a new approach to the optimal mount selection, and demonstrates through applications that it is efficient and reliable. This approach characterizes a mount by its effective stiffness rate and evaluates its deviation from an associated target. Continuous dummy variables are used to determine the selection targets through conventional processes for performance optimization.

This paper outlines a newly developed method for predicting the coupled response of structures from their uncoupled forced responses without having to know the forces acting on such structures. It involves computing the forced response of originally uncoupled structures with several mass loadings at a potential coupling point. The response data obtained from such computations is then used to predict the coupled response. The theory for discrete linear systems is outlined in the paper and a numerical example is given to demonstrate the validity, advantages and limitations of the method. The method is primarily devised to obtain coupled response of linear dynamic systems from independent and uncoupled analytical simulations. Its application significantly decreases computation time by reducing the simulation model size and is excellent for “what if” scenarios where a large number of simulations would otherwise be necessary.