Search Results

Over the course of the past decade, the automotive industry has made efforts to reduce the depth of the brazed aluminum, louver fin evaporators typically used in the air conditioning system for automobiles by increasing their compactness. Increasing fin and louver densities have led to the possibility of condensate affecting the air side performance of automotive evaporators. Condensate can “bridge” the space between two adjacent fins or louvers. Condensate bridging of the fins or louvers can alter the flow of air through the evaporator, causing a change in the heat transfer and friction characteristics. This study attempts to quantify these changes and determine which parameters will have an impact on them. Wind tunnel tests measuring the air side sensible heat transfer coefficient and pressure drop were conducted to examine how the air side heat transfer and friction characteristics of automotive evaporators are changed by the presence of condensate.

The operating conditions of a typical motorcycle are considerably different than those of a typical passenger car and thus require an oil capable of handling the unique demands. One primary difference, wet clutch lubrication, is already addressed by the current JASO four-stroke motorcycle engine oil specification (JASO T 903:2011). Another challenge for the oil is gear box lubrication, which may be addressed in part with the addition of a gear protection test in a future revision to the JASO specification. A third major difference between a motorcycle oil and passenger car oil is the more severe conditions an oil is subjected to within a motorcycle engine, due to higher temperatures, engine speeds and power densities. Scooters, utilizing a transmission not lubricated by the crankcase oil, also place higher demands on an engine oil, once again due to higher temperatures, engine speeds and power densities.

The Association des Constructeurs Européen d'Automobiles (ACEA) light duty diesel engine specifications requires a kinematic viscosity measurement technique for Peugeot XUD-11 BTE drain oils. This viscosity measurement is used to define the medium temperature dispersivity of soot in the drain oil.(1) This paper discusses the use of rotational rheology methods to measure the Newtonian character of XUD-11 drain oils. The calculation of the rate index using the Hershel Bulkley model indicates the level of non-Newtonian behavior of the drain oil and directly reflects the level of soot dispersion or agglomeration. This study shows that the more non-Newtonian the drain oil the greater the difference between kinematic and rotational viscosity measurements Oscillation (dynamic) rheological techniques are used to characterize build up of soot structure.

One of the key functions of lubricating oil additives in diesel engines is to control oil thickening caused by soot accumulation. Over the last several years, it has become apparent that the composition of the base oil used within the lubricant plays an extremely important role in the oil thickening phenomenon. In particular, oil thickening observed in the Mack T-8 test is significantly affected by the aromatic content of the base oil. We have found that the Mack T-8 thickening phenomenon is associated with high electrical activity, i.e., engine drain oils which exhibit high levels of viscosity increase show significantly higher conductivities. These findings suggest that electrical interactions are involved in soot-induced oil thickening.

This paper illustrates a method to determine the experimental uncertainties in the measurement of tailpipe emissions of carbon dioxide, carbon monoxide, nitrogen oxides, hydrocarbons, and particulates of medium-, and heavy-duty vehicles when tested on a heavy-duty chassis dynamometer and full-scale dilution tunnel. Tests are performed for different chassis dynamometer driving cycles intended to simulate a wide range of operating conditions. Vehicle exhaust is diluted in the dilution tunnel by mixing with conditioned air. Samples are drawn through probes for raw exhaust, diluted exhaust and particulates and measured using laboratory grade emission analyzers and a microbalance. At the end of a driving cycle, results are reported for the above emissions in grams/mile for raw continuous, dilute continuous, dilute bag, and particulate measurements.

In this study, multi-planar Nearfield Acoustical Holography (NAH) is used to investigate noise radiated from the front, side and rear areas of single tires on a two-wheel trailer. Contributions to the radiated noise from the leading edge, trailing edge, and sidewall of the tire are identified. Two tires - an experimental monopitch tire and a production passenger car tire - are evaluated on a smooth asphalt pavement at 58 km/hr. From the measured complex pressure, acoustic intensity is reconstructed on three planes surrounding the tire using modified NAH procedures. Additionally, sound power levels are presented in tabulated and spectra forms. Tire noise generating mechanisms are inferred based on the results.

Life Cycle Assessment (LCA) is a methodology used to determine quantitatively the environmental impacts of a range of options. The environmental community has used LCA to study all of the impacts of a product over its life cycle. This analysis can help to prevent instances where a greater degree of environmental harm results when changes are made to products based on consideration of impacts in only part of the life cycle. This study applies the methodology to engine lubricants, and in particular chlorine limits in engine lubricant specifications. Concern that chlorine in lubricants might contribute to emissions from vehicle exhausts of polychlorinated dibenzo-p-dioxins (PCDD) and polychlorinated dibenzofurans (PCDF), collectively called PCDD/F, led to the introduction of chlorine limits in lubricant specifications. No direct evidence was available linking chlorine in lubricants to PCDD/F formation, but precautionary principles were used to set lubricant chlorine limits.

The effect of knock intensity on exhaust emissions was examined in a single cylinder spark ignition engine. The exhaust components surveyed were carbon monoxide, carbon dioxide, oxides of nitrogen (as NO), and total unburned hydrocarbons. Knock was induced solely by changing the spark timing. To describe knock intensity quantitatively, the magnitudes of the rate of pressure irregularities occurring during the combustion process were utilized. The use of the rate of pressure change to define a quantitative knock intensity scale is supported by an apparent generalization of the stoichiometric air-fuel ratio data. Graphs are presented that indicate the dependency of power output as well as exhaust emissions on knock intensity for various air-fuel ratios.

Global emission legislations for diesel engines are becoming increasingly stringent. While the exhaust gas composition requirements for prior iterations of emission legislation could be met with improvements in the engine's combustion process, the next issue of European, North American and Japanese emission limits greater than 2005 will require more rigorous measures, mainly employment of exhaust gas aftertreatment systems. As a result, many American diesel OEMs are considering NOx adsorbers as a means to achieve 2007+ emission standards. Since the efficacy of a NOx adsorber over its lifetime is significantly affected by sulfur (“sulfur poisoning”), forthcoming reductions in diesel fuel sulfur (down to 15 ppm), have raised industry concerns regarding compatibility and possible poisoning effects of sulfur from the lubricant.

The world is firmly focused on reducing energy consumption and on increasingly stringent regulations on CO2 emissions. Examples of regulatory changes include the new United States Environmental Protection Agency's (U.S. EPA) fuel economy test procedures which were required beginning with the 2008 model year for vehicles sold in the US market. These test procedures include testing at higher speeds, more aggressive acceleration and deceleration, and hot-weather and cold-temperature testing. These revised procedures are intended to provide an estimate that more accurately reflects what consumers will experience under real world driving conditions. The U.S.

The potential for catalytically enhanced ignition in low-heat rejection Diesel engines has been experimentally studied under engine simulated conditions in a high pressure chemical flow reactor. Results are presented for propane oxidation on platinum at 6 and 10 atmospheres, at temperatures from 800K to 1050K, and at equivalence ratios from 0.5 to 4.0. For turbulent transport rates which are typical of those in an engine, as much as 20% of the fuel was found to react on the catalyst before the onset of the gas-phase ignition reactions. Depending on the adiabaticity of the combustion chamber walls, this could lead to significant thermal enhancement of the gas-phase ignition process. Evidence of chemical enhancement was also observed, at 10 atm under very fuel rich conditions, in terms of a change in the concentration and distribution of the hydrocarbon intermediate species. Possible mechanisms for the observed chemical enhancement due to surface generated species are discussed.

The development of new transmission designs continues to affect the vehicle market. Continuously variable transmissions (CVTs) remain one of the more recent designs that impact the vehicle market. A desire for high belt-pulley capacity has driven studies concentrating on metal-on-metal (M/M) friction as a function of the CVT fluid. This paper describes the statistical techniques used to optimize the fluid friction as a function of additive components in a bench-scale, three-element test rig.

This paper outlines the history and background of the NLGI (formerly known as the National Lubricating Grease Institute) lubricating grease specifications, GC-LB classification of Automotive Service Greases as well as details on the development of new requirements for their High-Performance Multiuse (HPM) grease certification program. The performance of commercial lubricating grease formulations through NLGI's Certification Mark using the GC-LB Classification system and the recently introduced HPM grease certification program will be discussed. These certification programs have provided an internationally recognized specification for lubricating grease and automotive manufacturers, users and consumers since 1989. Although originally conceived as a specification for greases for the re-lubrication of automotive chassis and wheel bearings, GC-LB is today recognized as a mark of quality for a variety of different applications.

The structural excitation by turbulent flow pressure fluctuations continues to be an important part of vehicle NVH analysis and design. Much of the analytical work on turbulent flow has been limited to flow over smooth, flat surfaces. Measurements and CFD analyses show a significantly different pressure spectrum for flows over an obstruction. The coupling of the turbulent pressure excitation to the structural vibration and transmitted sound depends on the spatial matching between the source and response fields. This paper develops an analytical model for the spatial correlation of turbulent flow pressure fluctuations downstream of an obstruction. Such a model is useful in the early design stage of a vehicle and is compatible with SEA models of the fluid structure interaction.

SAE 2004-01-3009 reported on work conducted to investigate the correlation between the Mack T-11 laboratory engine tests and vehicle field tests. It concluded that the T-11 test provides an effective screening tool to investigate soot-related viscosity increase, and the severity of the engine test limits provides a substantial margin of safety compared to the field. This follow-up paper continues the studies on the 2003 Mack CV713 granite dump truck equipped with an AI-427 internal EGR engine and introduces experimentation on a 2003 CX613 tractor unit equipped with an AC-460P cooled EGR engine. The paper further assesses the correlation of the field trials to the Mack T-11 engine test and reviews the impact of ultra low sulfur diesel (ULSD) and prototype CJ-4 lubricant formulations in these engines.

Soot related viscosity increase has been reported as a field issue in some diesel engines and this led to the development of the T-11 engine test, incorporated in the Mack EO-N Premium Plus 03 specification (014 GS 12037). This study compares T-11 laboratory engine tests and vehicle field tests and seeks to confirm the correlation between them. The findings are that the T-11 test provides an effective screening tool to investigate soot related viscosity increase, and the severity of the engine test limits gives a substantial margin of safety compared to the field. A complementary study was conducted in conjunction with this work that focuses on the successful application of electrochemical sensor technology to diagnose soot content and soot related viscosity increase. This will be the subject of a separate paper.

New technologies are being commercialized across the automotive industry to address demands for improved fuel economy, emissions reductions, and improved customer satisfaction. Push-belt continuously variable transmissions (b-CVTs) are beginning to command a significant percentage of the market now dominated by manual and conventional automatic transmissions. In addition, automobile manufacturers plan to introduce the first traction drive toroidal-CVTs to the market place within the next five years. A review of the relative benefits and limitations of each of these automatic transmissions exists in the literature. In this paper we consider how the performance requirements of each of these automatic transmission systems impact automatic transmission fluid technology. The physical characteristics and screen test performance of two commercial ATFs, a b-CVTF, and two traction fluids were examined.

Raw oils generated by low-temperature coal pyrolysis were chemically characterized and subjected to tests in three diesel engines of different configuration. The coal liquids were tested as blends with conventional No. 2 diesel fuels, the coal liquids being 20-25% by volume. These tests were performed in support of a broader set of studies on the feasibility of using low-temperature pyrolysis to obtain liquid fuel materials from coal that do not require extensive, costly upgrading. Determination of physical and chemical properties of the pyrolysis liquids indicated a higher hydrogen/carbon ratio and lower aromaticity than typical SRC II and EDS middle distillates. Combustion tests were performed in both direct- and indirect-injection engines at three sites. The results were highly variable, the addition of the oil showing no effect on emissions and performance in some cases, reduced emissions on one engine, and increased emissions in other cases.

Recently, research and testing of oxygenated diesel fuels has increased, particularly in the area of exhaust emissions. Included among the oxygenated diesel fuels are blends of diesel fuel with ethanol, or E diesel fuels. Exhaust emissions testing of E diesel fuel has been conducted by a variety of test laboratories under various conditions of engine type and operating conditions. This work reviews the existing public data from previous exhaust emissions testing on E diesel fuel and includes new testing performed in engines of varied design. Emissions data compares E diesel fuel with normal diesel fuel under conditions of different engine speeds, different engine loads and different engine designs. Variations in performance under these various conditions are observed and discussed with some potential explanations suggested.

The oxidation of 1-butene and n-butane in air at elevated pressure was investigated in a high pressure chemical flow reactor. Results are presented for pressures of 3, 6, and 10 atm, temperatures near 900K, and lean equivalence ratio. Gas samples were analyzed using gas chromatography with aldehydes sampled using a dinitrophenylhydrazine/acetonitrile procedure employing gas chromatography/mass spectrometry analysis. Major common products observed include CO, CH2O, C2H4, C3H6, and CO2. Additional major products included 1,3-C4H6 for 1-butene and 1-C4H8 for n-butane. Fuel conversion was increased with increased pressure, temperature, and equivalence ratio with 1-butene more reactive than n-butane. Large levels of lower molecular weight carbonyls resulted from 1-butene whereas significant amounts of conjugate and lower molecular weight alkenes resulted from n-butane. Trends in product distributions with increasing pressure were successfully accounted for by current autoignition theories.