Search Results

A KIA Soul was instrumented to measure the relative velocity (magnitude and yaw angle) at the front of the vehicle and in-cabin sound at a location close to the side glass near the A-pillar vortex impingement. Tests were conducted at a proving ground under a range of conditions from low wind conditions (~3 m/s) to moderate (7-8 m/s) wind speeds. For any given set of atmospheric conditions the velocity and sound data at any given position on the proving ground were noted to be very repeatable, indicating that the local wakes dominated the "turbulent" velocity field. Testing was also conducted in an aeroacoustic wind tunnel in smooth flow and with a number of novel turbulence generating methods. The resulting sounds were analyzed to study the modulation at frequencies likely to result in fluctuation strength type noise.

Wind tunnels provide a convenient, repeatable method of assessing vehicle engine cooling, yet important draw-backs are the lack of a moving ground and rotating wheels, blockage constraints and, in some tunnels, the inability to simulate ambient temperatures. A series of on-road and wind-tunnel experiments has been conducted to validate a process for evaluating vehicle cooling system performance in a high blockage aerodynamic wind tunnel with a fixed ground simulation. Airflow through the vehicle front air intake was measured via a series of pressure taps and the wind-tunnel velocity was adjusted to match the corresponding pressures found during the road tests. In order to cope with the inability to simulate ambient temperatures, the technique of Specific Dissipation (SD) was used (which has previously been shown to overcome this problem).

A pressure-based technique has been developed for the purpose of radiator cooling airflow measurement. The technique was effectively utilised to quantify the local time-averaged air velocity through radiator cores in a small wind tunnel. The pressure difference indicated by the technique was found to be a function of the normal component of the air velocity. This paper describes the development and use of the technique which is compact, robust and non-intrusive. By applying this technique, the airflow distribution across the radiator face has been measured for a complete vehicle in an aerodynamic wind tunnel and in an environmental chamber. Results are compared for the different test environments. The influence of airflow distribution on the Specific Dissipation (a parameter used for evaluating radiator cooling performance) is examined and results for propeller-based methods and pressure-based methods are compared.

This paper summarises the effects of turbulence on the aerodynamics of road vehicles, including effects on forces and aero-acoustics. Data are presented showing that a different design of some vehicles may result when turbulent flow is employed. Methods for generating turbulence, focusing on physical testing in full-size wind tunnels, are discussed. The paper is Part Two of a review of turbulence and road vehicles. Part One (Cooper and Watkins, 2007) summarised the sources and nature of the turbulence experienced by surface vehicles.

This paper is the first of two papers that address the simulation and effects of turbulence on surface vehicle aerodynamics. This, the first paper, focuses on the characteristics of the turbulent flow field encountered by a road vehicle. The natural wind environment is usually unsteady but is almost universally replaced by a smooth flow in both wind tunnel and computational domains. In this paper, the characteristics of turbulence in the relative-velocity co-ordinate system of a moving ground vehicle are reviewed, drawing on work from Wind Engineering experience. Data are provided on typical turbulence levels, probability density functions and velocity spectra to which vehicles are exposed. The focus is on atmospheric turbulence, however the transient flow field from the wakes of other road vehicles and roadside objects are also considered.

In this paper, a theoretical model for the calculation of Specific Dissipation (SD) was developed. Based on the model, the effect of ambient and coolant radiator inlet temperatures on SD has been predicted. Results indicate that the effect of ambient and coolant inlet temperature variation on SD is small (less than 2%) when ambient temperature varies between 10 and 50°C and coolant radiator inlet temperature between 60 and 120°C. The effect of coolant flowrate on SD is larger if there is a larger flowrate variation. Experimental results indicate that a 1 % variation at 1.0 L/s will cause about ±0.6% SD variation. Therefore the flowrate should be carefully controlled.

Modern exhaust systems contain not only a piping network to transport hot gas from the engine to the atmosphere, but also functional components such as the catalytic converter and turbocharger. The turbocharger is common place in the automotive industry due to their capability to increase the specific power output of reciprocating engines. As the exhaust system is a main heat source for the under body of the vehicle and the turbocharger is located within the engine bay, it is imperative that accurate surface temperatures are achieved. A study by K. Haehndel [1] implemented a 1D fluid stream as a replacement to solving 3D fluid dynamics of the internal exhaust flow. To incorporate the 3D effects of internal fluid flow, augmented Nusselt correlations were used to produce heat transfer coefficients. It was found that the developed correlations for the exhaust system did not adequately represent the heat transfer of the turbocharger.

At the rear of the vehicle an end acoustic silencer is attached to the exhaust system. This is primarily to reduce noise emissions for the benefit of passengers and bystanders. Due to the location of the end acoustic silencer conventional thermal protection methods (heat shields) through experimental means can not only be difficult to incorporate but also can be an inefficient and costly experience. Hence simulation methods may improve the development process by introducing methods of optimization in early phase vehicle design. A previous publication (Part 1) described a methodology of improving the surface temperatures prediction of general exhaust configurations. It was found in this initial study that simulation results for silencer configurations exhibited significant discrepancies in comparison to experimental data.

Vortices formed around the A-pillar region dictates the pressure distribution on the side panels of a passenger vehicle and also can lead to aerodynamic noise generation. This paper compares the suitability of various turbulence models in simulating the flow behind a vehicle A-pillar region under laboratory operating conditions. Commercial software's (FLUENT and SWIFT) were used to compare the performance of various turbulence models. In FLUENT, a simplified vehicle model with slanted A-pillar geometry was generated using GAMBIT and in SWIFT, the simplified vehicle model was generated using Fame Hybrid. Computational Fluid Dynamics (CFD) simulations were carried out using FLUENT under steady state conditions using various turbulence models (k-, k- Realize, k- RNG, k- and Spalart Allamaras). In SWIFT, k-, A-RSM and HTM2 turbulence models were used for the steady state simulations. Investigations were carried out at velocities of 60, 100 and 140km/h and at 0-degree yaw angle.

Exhaust heat recovery systems are used to make use of otherwise wasted heat from a car engine. The purpose of exhaust heat recovery systems is to reduce the fuel consumption of the car and consequently reduce CO2 emissions. The unique system design described herein utilises thermoelectric generators (TEGs) and heat pipes with its key advantage being it is a passive solid state design. The use of these components creates a few design constraints. For example, both the TEGs and heat pipes have operating temperature limitations. In this paper, a naphthalene heat pipe preheat exchanger is proposed to deal with this problem. Exhaust conditions measured from a representative spark ignition engine were used in a numerical simulation to predict the performance of the exhaust heat recovery system. If 8 modules are used and the engine is producing 8kW of mechanical power, the system is predicted to produce 53.75W of electrical power.

The paper considers a novel waste heat recovery (WHR) system integrated with the engine architecture in a hybrid electric vehicle (HEV) platform. The novel WHR system uses water as the working media and recovers both the internal combustion engine coolant and exhaust energy in a single loop. Results of preliminary simulations show a 6% better fuel economy over the cold start UDDS cycle only considering the better fuel usage with the WHR after the quicker warm-up but neglecting the reduced friction losses for the warmer temperatures over the full cycle.

The function of a rear view mirror is a determining factor in its shape - resulting in a flat rear mirrored face. The resulting bluff body generates unsteady base pressures which generate unsteady forces, leading to movement of the mirror surface and potential image blurring. The objective of this paper was to experimentally determine the fluctuating base pressure on a standard and modified mirror. Half a full-size vehicle was utilised, fixed to the side wall of a wind tunnel. A dynamically responsive multi channel pressure system was used to record the pressures. The modification to the mirror consisted of a series of extensions to the mirror rim, to see if this method would attenuate the fluctuating base pressures. It was found that increasing the length of the extension changed the pressure pattern across the face, and the over all magnitude of the fluctuations reduced with increasing length of extension. It was recommended to further the work via phase measurements.

This paper describes a high-speed electrical machine for an aircraft starter-generator. A surface mounted permanent magnet machine is designed to have minimal rotor losses and a novel cooling system for the stator. An inner stator sleeve is adopted to allow for a flooded stator whilst minimizing rotor windage losses. Different slot-pole combinations are compared in view of attaining an optimal combination that provides minimum losses whilst satisfying the electromagnetic, mechanical and thermal constraints.

The focus of internal combustion (IC) engine research is the improvement of fuel economy and the reduction of the tailpipe emissions of CO2 and other regulated pollutants. Promising solutions to this challenge include the use of both direct-injection (DI) and alternative fuels such as liquefied petroleum gas (LPG). This study uses Mie-scattering and schlieren imaging to resolve the liquid and vapor phases of propane and iso-octane, which serve as surrogates for LPG and gasoline respectively. These fuels are imaged in a constant volume chamber at conditions that are relevant to both naturally aspirated and boosted, gasoline direct injection (GDI) engines. It is observed that propane and iso-octane have different spray behaviors across these conditions. Iso-octane is subject to conventional spray breakup and evaporation in nearly all cases, while propane is heavily flash-boiling throughout the GDI operating map.

Effective rear view vision from external mirrors is compromised at high speed due to rotational vibration of the mirror glass. Possible causes of the mirror vibration are reviewed, including road inputs from the vehicle body and a variety of aerodynamic inputs. The latter included vibrations of the entire vehicle body, vibrations of the mirror “shell”, the turbulent flow field due to the A-pillar vortex (and to a lesser extent the approach flow) and base pressure fluctuations. Experiments are described that attempt to understand the relative influence of the causes of vibration, including road and tunnel tests with mirrors instrumented with micro accelerometers. At low frequencies, road inputs predominate, but some occur at such low frequencies that the human eye can track the moving image. At frequencies above about 20Hz the results indicate that at high speeds aerodynamics play a dominant role.

With the purpose of reducing emission level while maintaining the high torque character of diesel engine, various solutions have been proposed by researchers over the world. One of the most attractive methods is to use dual fuel technique with premixed gaseous fuel ignited by a relatively small amount of diesel. In this study, Methane (CH4), which is the main component of natural gas, was premixed with intake air and used as the main fuel, and diesel fuel was used as ignition source to initiate the combustion. By varying the proportion of diesel and CH4, the combustion and emissions characteristics of the dual fuel (diesel/CH4) combustion system were investigated. Different cases of CFD studies with various concentration of CH4 were carried out. A validated 3D quarter chamber model of a single cylinder engine (diesel fuel only) generated by using AVL Fire ESE was modified into dual fuel mode in this study.

The innovative highly flexible wings made of extremely light structures, yet still capable of carrying a considerable amount of non- structural weights, requires significant effort in structural simulations. The complexity involved in such design demands for simplified mathematical tools based on appropriate nonlinear structural schemes combined with reduced order models capable of predicting accurately their aero-structural behaviour. The model presented in this paper is based on a consistent nonlinear beam-wise scheme, capable of simulating the unconventional aeroelastic behaviour of flexible composite wings. The partial differential equations describing the wing dynamics are expanded up to the third order and can be used to explore the effect of static deflection imposed by external trim, the effect of gust loads and the one of nonlinear aerodynamic stall.

The aim of this paper is to develop a new concept of unconventional airship based on morphing a lenticular shape while preserving the volumetric dimension. Lenticular shape is known to have relatively poor aerodynamic characteristics. It is also well known to have poor static and dynamic stability after the certain critical speed. The new shape presented in this paper is obtained by extending one and reducing the other direction of the original lenticular shape. The volume is kept constant through the morphing process. To improve the airship performance, four steps of morphing, starting from the lenticular shape, were obtained and compared in terms of aerodynamic characteristics, including drag, lift and pitching moment, and stability characteristics for two different operational scenarios. The comparison of the stability was carried out based on necessary deflection angle of the part of tail surface.

Significant research has been made on traditional pre-mixed charge Spark-Ignition Natural-Gas engines which have seen widespread usage across the automotive sector. Many researchers including those in industry are now exploring the Direct-Injection concept for Natural-Gas Spark-Ignition engines. Direct-Injection has significant performance benefits over port-fuel injection, primarily due to increased volumetric efficiency as a result of injecting the fuel after intake valve closure. This could lead to enhanced driving performance over port-fuel injection comparable to gasoline engines. Furthermore, Direct-Injection with increased compression ratio in conjunction with downsizing concepts has the potential to increase thermal efficiency while exhibiting significantly lower CO2 emissions. Advanced combustion strategies like stratified mixture combustion has been widely studied for gasoline and proven to increase the low load thermal efficiency over homogeneous stoichiometric combustion.

Accurate and robust tracking of objects is of growing interest amongst the computer vision scientific community. The ability of a multi-sensor system to detect and track objects, and accurately predict their future trajectory is critical in the context of mission- and safety-critical applications. Remotely Piloted Aircraft System (RPAS) are currently not equipped to routinely access all classes of airspace since certified Detect-and-Avoid (DAA) systems are yet to be developed. Such capabilities can be achieved by incorporating both cooperative and non-cooperative DAA functions, as well as providing enhanced communications, navigation and surveillance (CNS) services. DAA is highly dependent on the performance of CNS systems for Detection, Tacking and avoiding (DTA) tasks and maneuvers.