Search Results

Innovative solutions for reducing particulate emissions will be necessary in order to comply with the even more stringent exhaust-gas standards of the future. The potential of a diesel nozzle with variable orifice geometry has long been common knowledge in the area of engine construction. But up to now, a fully functional solution of such a nozzle has not appeared which operates with a reduced orifice at low engine speeds and/or low loads. Here with regard to target costing, the requirements implicit in function and manufacture must also be taken into account. Using calculations on nozzle interior flow and injection-spray investigations, it will be shown which nozzle geometries best fulfill the various requirements. In order to achieve low levels of particulate emission in an engine with a combustion chamber designed for optimum use of a hole-type nozzle, the injection-spray direction and its geometry must to a large extent correspond to those of a hole-type nozzle.

In exhaust systems with selective catalytic reduction (SCR) a fast conversion of liquid urea to gaseous ammonia and a uniform distribution of the ammonia vapor upstream of the SCR catalyst are essential to reduce the nitric oxides efficiently. For the prediction of the mixing process and the transport of ammonia vapor with the CFD method an accurate description of the turbulent flow field is a basic requirement. This paper presents the comparison of simulation results using three different turbulence models (high-Re kε-RNG model, low-Re kω-SST model, Reynolds stress model) with measurements of the turbulent velocity field using Laser Doppler Anemometry (LDA). The investigations were carried out for a SCR system with a swirl mixer on a cold flow test bench for two different volume flows. From the measured velocity signals different components of the Reynolds-tensor were derived.

Software-in-the-Loop (SiL) test environments are the ideal virtual platforms for enabling continuous-development, -integration, -testing -delivery or -deployment commonly referred as Continuous-X (CX) of the complex functionalities in the current automotive industry. This trend especially is contributed by several factors such as the industry wide standardization of the model exchange formats, interfaces as well as architecture definitions. The approach of frontloading software testing with SiL test environments is predominantly advocated as well as already adopted by various Automotive OEMs, thereby the demand for innovating applicable methods is increasing. However, prominent usage of the existing monolithic architecture for interaction of various elements in the SiL environment, without regarding the separation between functional and non-functional test scope, is reducing the usability and thus limiting significantly the cost saving potential of CX with SiL.

The range of Robert Bosch in-line pumps is designed for engines with cylinder outputs of up to 200 kW. Within this family of pumps the MW pump is used in small IDI engines and medium-sized DI engines with cylinder outputs in the region of 30 kW. More stringent exhaust emission legislation and the need to ensure optimum fuel economy call for efficient fuel-injection systems for diesel engines. In both of its designs the new MW pump meets these more exacting requirements and forms the contribution of Robert Bosch GmbH toward developing advanced diesel engines.

The Bosch Common Rail Fuel Injection System with the new technologies developed for the Duramax 6600 engine offer numerous performance advantages including exhaust emissions control and noise. The layout of the fuel system components and electrical parts is specifically designed to control fuel injection characteristics. The new injector and nozzle technology was integrated to achieve the required system performance. The new 1600bar fuel pump is also a prerequisite for required system performance.

The tightening of Heavy Duty Diesel (HDD) emissions legislation throughout the world is leading to the development of emission control devices to enable HDD engines to meet the new standards. NOx and Particulate Matter (PM) are the key pollutants which these emission control systems need to address. Diesel Particulate Filters (DPFs) are already in use in significant numbers to control PM emissions from HDD vehicles, and Selective Catalytic Reduction (SCR) is a very promising technology to control NOx emissions. This paper describes the development and performance of the Compact SCR-Trap system - a pollution control device comprising a DPF-based system (the Continuously Regenerating Trap system) upstream of an SCR system. The system has been designed to be as easy to package as possible, by minimising the total volume of the system and by incorporating the SCR catalysts on annular substrates placed around the outside of the DPF-based system.

The reduction of nitrous oxides in the exhaust gases of internal combustion engines using a urea water solution is gaining more and more importance. While maintaining the future exhaust gas emission regulations, like the Euro 6 for passenger cars and the Euro 5 for commercial vehicles, urea dosing allows the engine management to be modified to improve fuel economy as well. The system manufacturer Robert Bosch has started early to develop the necessary dosing systems for the urea water solution. More than 300.000 Units have been delivered in 2007 for heavy duty applications. Typical dosing quantities for those systems are in the range of 0.01 l/h for passenger car systems and up to 10 l/h for commercial vehicles. During the first years of development and application of urea dosing systems, instantaneous flow measuring devices were used, which were not operating fully satisfactory.

In view of tight emission standards, injection strategies to reduce raw HC-emissions during the cold starting of port fuel injected engines are evaluated in this study. The relevance of spray targeting and atomization is outlined in the first part of this paper. The foundation and performance of different injector concepts with respect to spray characteristics are discussed. Laboratory experiments demonstrate that concepts relying on auxiliary energy, such as air-assistance, fuel heating and injection at elevated system pressures, are capable of producing spray droplet sizes in the SMD-range of 25μm. For future injection strategies aimed at the compliance of SULEV emission levels, this target value is considered to be essential. In the second part of this paper, emission tests of selected injector concepts are carried out using a V6-3.2I ULEV engine operated both in a vehicle and on a test bench.

Vehicle inspection in repair shops is often still based on paper forms. Information Technology (IT) does not yet support the entire inspection process. In this paper, we introduce a small wearable IT device that is controlled by speech and enables service technicians to wirelessly access relevant data and to perform on-site communication. Users can carry this device in a pocket and use a small headset to enter speech and receive audio feedback. This system provides a completely speech-enabled functionality and thus offers a hands-free operation. After showing the applicability of wearable computers in this environment, we developed a proprietary hardware system consisting of a thin-client connected via a Digital Enhanced Cordless Telecommunications (DECT) link to a standard Personal Computer (PC) that runs a speech engine and hosts a database. Several field tests in garages helped us during the evolution of our prototypes where service technicians critiqued the prototypes.

Secondary air injection after cold start gives two effects for reduced exhaust emissions: An exothermic reaction at the hot exhaust valves occurs, which increases the temperature of the exhaust gas. It gives sufficient air to the catalyst during the cold start fuel enrichment that is necessary to prevent driveability problems. Handicaps for the wide use of air injection include space constraints, weight and price. An electrical air blower was choosen to best satisfy all these requirements. The development steps are described. The result is a three stage radialblower with extremly high revolutions of about 18000 rpm. The system configuration and the outcome are demonstrated on the new C-Class of Mercedes-Benz. The results show emission reductions higher than 50 %, while also satisfying the development goals of noise, volume, weight and cost requirements.

An optimized monofuel CNG light duty vehicle based on the Opel Zafira was investigated under real-world conditions and the results are presented in this study. To analyze the real-world performance of the monofuel CNG vehicle due to fuel consumption and exhaust emissions representative experimental test on road-test routes were performed, including sections with significantly different driving conditions. Furthermore, driving tests at different constant speeds on freeway were carried out. A benchmarking to the same vehicle with diesel powertrain was done as well. The test vehicles were equipped with a new compact on-board measurement system and additionally GPS tracking to link the received geographic information of the road-test routes with the measured exhaust mass emission data. The measurement results were validated with Matlab Simulink models of the powertrain and vehicle.

In this study the performance of a monofuel compressed natural gas articulated truck was investigated under real-world conditions. To analyze the CNG vehicle due to fuel consumption and exhaust emissions a representative road-test route was conducted, including sections with significantly different driving conditions. Moreover, driving tests on freeway under higher load were carried out. As experimental equipment, a new ultra compact on-board system measured the in-car exhaust mass emissions in real time. Every second, a full dataset of CO₂, CO, HC and NOx emission rates was provided. The real-world emission measurements are based on a modal analysis of the emission concentrations in the tailpipe of the vehicle. The exhaust gas mass flow is calculated from the air mass flow and the gas components with a real-time reaction model. In combination with the vehicle speed, the emission rates in g/s are then calculated in gram per kilometer.

The objective of the project was to compare the exhaust gas emissions and fuel consumption of a test vehicle, which was on a one hand operating with premium gasoline 95 RON (RON 95) and a mixture of 90% by volume premium gasoline 95 RON and 10% by volume of high purity bio ethanol (E10) on the other hand. As a test vehicle a Skoda Octavia station wagon was used. The engine of the tested vehicle corresponded to the Euro 4 emission standard. The investigations were conducted under the real world conditions, and also at the chassis dynamometer test bench. The tested vehicle was equipped with a new On-board measurement System (OBM) to determine the mass emissions on real world driving routes. The measurement method is based on modal analysis of the emission concentrations in the tailpipe of the vehicle, and real time exhaust mass flow determination.

Increasing injection pressures together with Diesel fuel lubricated Common Rail pumps replacing oil lubricated systems demand a more sophisticated investigation of robustness and durability against particle contamination of fuel. The established way of requiring filtration efficiency levels per lab standard is not significant enough if we look at variable factors like vibration of the fuel filter and viscosity of the fuel. Because these and other factors tremendously influence filtration efficiency, future Diesel FIE cleanliness requirements will need to define an allowable contamination limit downstream of the filter. More precisely, this is not a scalar limit but a contamination collective that considers the varying vehicle filtration and operating environment. This paper describes a procedure for defining allowable contamination limits of the FIE components. The procedure includes sensitivity, robustness and “key life” tests.

This paper focuses on the potentials of a Belt-Starter-Generator (BSG) in the context of an ultra-light vehicle prototype with a target curb weight of only 600 kg. Therefore, two hybrid approaches with a voltage level below 60 V are described and their potentials regarding electrical driving and CO2 reduction are analysed in detail. Introducing the ‘Cars Ultra-Light Technology’ (CULT) project, the holistic lightweight approach is described as a main requirement for the further hybrid investigations. In addition, a P2-hybrid structure with a 12 V BSG on the transmission input shaft enabled unique features despite the low voltage level and limited electrical power resources. The CO2 reduction for this powertrain combination is described and compared to a conventional stop start configuration. The validation process on a dynamic test rig is presented as well.

Future legislations claim further reduction of all restricted emissions as well as the limitation of soot emissions in diesel engines. Special alternative diesel fuels that do not contain aromatic compounds, therefore, promise great potential for further reduction of HC, CO and particulate emissions. During a research project carried out at the Institute for Powertrains and Automotive Technology at the Vienna University of Technology, the potential of alternative diesel fuels was investigated using a state-of-the-art diesel engine with common rail direct injection. The testing took part using an engine test rig as well as on the chassis dynamometer test bench to demonstrate the emission levels in real life conditions. As real biofuel, pure HVO (Hydrogenated Vegetable Oil) was investigated and additionally in different blends with fossil diesel fuel.

Increasingly stringent Diesel vehicle emissions legislation around the world means that advanced aftertreatment systems may be required to achieve the required nitrogen oxide (NOx) emissions rather than through engine control measures alone. As in lean-burn gasoline applications, NOx adsorber systems offer great potential for high level NOx conversion in Diesel exhaust, and their use on Diesel engines is an area of intense interest for possible use in light-duty and heavy-duty applications. This paper is concerned with the performance of advanced NOx adsorber catalysts developed specifically for the requirements of light-duty Diesel vehicles. Laboratory and engine bench data are discussed that demonstrate NOx conversions in excess of 90% over a wide temperature window can be achieved. The durability characteristics of these catalysts are also reported.

The emissions legislation in the US and Europe introduces the need for the application of diesel particulate filters (DPF) in most diesel vehicles. In order to fulfill future OBD legislations, which include more stringent requirements on monitoring the functionality of those particulate filters, new sensors besides the differential pressure sensor are necessary. The new sensors need to directly detect the soot emission after DPF and withstand the harsh exhaust gas environment. Based on multi layer ceramic sensor technology, an exhaust gas sensor for particulate matter (EGS-PM) has been developed. The soot-particle-sensing element consists of two inter-digitated comb-like electrodes with an initially infinite electrical resistance. During the sensor operation, soot particles from the exhaust gas are collected onto the inter-digital electrodes and form conductive paths between the two electrode fingers leading to a drop of the electrical resistance.

The electrification of vehicles marks the introduction of new products to the automotive market and a continued effort to optimize their performance. The electric motor is an important component with which a further optimization of efficiency, power density and cost can be achieved. Additional benefits can be realized in the laminated core. This paper presents an innovative method to produce laminated stacks by a chain of processes different from conventional ways. The process chain presents a sequence of precision blanking, buffering, heat treatment and gluing. The effect of these processes is compared with existing solutions that typically contain some individual features but usually not the combination that enhances the overall effect. The heat treatment decreases residual stresses from previous process steps and reduces power losses in the laminated core. Depending on the design, benefits around 20% are found.

As legislation tightens in the Heavy Duty Diesel (HDD) area it is essential to develop systems with high activity and excellent durability for both Particulate Matter (PM) and NOx control. The Continuously Regenerating Trap (CRT™) system controls hydrocarbon (HC), CO and PM emissions from HDD vehicles with efficiencies of over 90%, and has demonstrated very good field durability over distances exceeding 700,000 km. The system is widely used in Europe, and is demonstrating the same high performance and excellent durability within field applications in North America. The Continuously Regenerating Trap (CRT™) system has been developed and patented by Johnson Matthey [1]. Throughout this paper this system will be referred to as the Continuously Regenerating Diesel Particulate Filter, CR-DPF. The CR-DPF comprises an oxidation catalyst, optimised for NO2 generation from the engine-out NOx, and a downstream DPF.