Search Results

RADIATION can produce almost instantaneous failure of modern aircraft lubricants, tests at Southwest Research Institute show. Two types of failures demonstrated are rapid viscosity rise and loss of heat conductivity. Furthermore, it was found that lubricants can become excessively corrosive under high-level radiation. Generally speaking, the better lubricants appeared to improve in performance while marginal ones deteriorated to a greater extent under radiation. When the better lubricants were subjected to static irradiation prior to the deposition test, there was a minor increase in deposition number as the total dose was increased.

This paper describes a study to determine the influence of preimpact vehicle braking on the positions and postures of unrestrained, children in the front seat at the time of collision. Anesthetized baboons were used as child surrogates. The unrestrained animals were placed in various initial sitting, kneeling, and standing positions typically assumed by children while traveling in automobiles. Tests were conducted with various front seat positions and seat covering materials. Measurements were made of pertinent vehicle dynamics and surrogate kinematics during the hard braking event. For each initial condition evaluated, a photosequence is given showing typical positions and postures of the surrogate during the braking event.

Radioactive tracer technology (RAT) is an important tool in measuring component wear in an operating engine on a real-time basis. This paper will discuss the use of RAT to study and evaluate boundary lubricant and surfactant chemistries aimed at providing benefits in wear control. In particular, RAT was employed to study ring and bearing wear as a function of engine operating condition (speed, load, and temperature) and lubricant characteristics. Prior to testing, the engine's compression rings and connecting rod bearings were subjected to bulk thermal neutron bombardment in a nuclear reactor to produce artificial radioisotopes that were separately characteristic of the ring and bearing wear surfaces. The irradiated parts were installed in the test engine, after which testing to a specific test matrix was accomplished.

The Department of Transportation (DOT) National Highway Traffic Safety Administration (NHTSA) awarded a contract to Southwest Research Institute (SwRI) to conduct research and testing in the interest of motorcoach fire safety. The goal of this program was to develop and validate procedures and metrics to evaluate current and future detection, suppression, and exterior fire-hardening technologies that prevent or delay fire penetration into the passenger compartment of a motorcoach - in order to increase passenger evacuation time. The program was initiated with a literature review and characterization of the thermal environment of motorcoach fires and survey of engine compartments, firewalls, and wheel wells of motorcoaches currently in North American service. These characterizations assisted in the development of test methods and identification of the metrics for analysis. Test fixtures were designed and fabricated to simulate a representative engine compartment and wheel well.

A new generation of vehicle dynamics and powertrain control technologies are being developed to leverage information streams enabled via vehicle-to-vehicle (V2V) and vehicle-to-infrastructure (V2I) connectivity [1, 2, 3, 4, 5]. While algorithms that use these connected information streams to enable improvements in energy efficiency are being studied in detail, methodologies to quantify and analyze these improvements on a vehicle have not yet been explored fully. A procedure to test and accurately measure energy-consumption benefits of a connected and automated vehicle (CAV) is presented. The first part of the test methodology enables testing in a controlled environment. A traffic simulator is built to model traffic flow in Fort Worth, Texas with sufficient accuracy. The benefits of a traffic simulator are two-fold: (1) generation of repeatable traffic scenarios and (2) evaluation of the robustness of control algorithms by introducing disturbances.

The design of helical Intake ports for swirl generation is a process that has been developed over a number of years through primarily empirical methods. A number of design rules have been established that enable designers to develop ports that approach the state-of-the-art for maximum swirl generation with minimum pressure loss. More recently, computer-aided design (CAD) tools have been introduced that permit geometry and features to be accurately defined by mathematical surface descriptions, and to be parameterized such that derived geometry is updated automatically along with parent features. The author has developed a parametric design approach for helical ports that incorporates the lessons learned from experience into a systematic design procedure. This procedure takes advantage of the current CAD capabilities to expedite the design process and improve the result.

SCR-on-filter, or SCRoF, is an emerging technology for different market segments and vehicle applications. The technology enables simultaneous particulate matter trapping and NOX reduction, and provides thermal management and aftertreatment packaging benefits. However, there is little information detailing the lubricant derived exposure effects on functional SCR performance. A study was conducted to evaluate the impact of various oil consumption pathways on a light duty DOC and SCRoF aftertreatment system. This aftertreatment system was aged utilizing an engine test bench modified to enable increased oil consumption rates via three unique oil consumption pathways. The components were characterized for functional SCR performance, ash morphology, and ash deposition characteristics. This included utilizing techniques, such as SEM / EDS, to evaluate the ash structures and quantify the ash elemental composition.

Copper ion exchange procedures were used to prepare zeolite-based catalysts for NOx reduction in lean (oxygen-rich) exhaust. Energy dispersive x-ray fluorescence and scanning electron microscopy analyses confirmed the presence of copper in the zeolite matrix. Zeolites were applied onto honeycomb and foam substrates, and evaluated for catalytic NOx reduction efficiency using engine exhaust. Copper-exchanged zeolite catalysts prepared for this study revealed NOx reduction of 95 percent for a period of seven minutes using previously adsorbed exhaust hydrocarbons as the reducing agent. Experiments using ethylene injection to supplement the exhaust suggest long-term and sustained NOx reduction, initially observed at 52 percent. Experimental results and performance comparisons of ZSM-5, mordenite, and Y-type zeolites are discussed. Zeolite catalysts based on Cu-mordenite showed high levels of initial NOx reduction, while results using Cu-ZSM-5 suggested better long-term activity.

Excessive interior noise and vibration in propeller driven general aviation aircraft can result in poor pilot communications with ground control personnel and passengers, and, during extended flights, can lead to pilot and passenger fatigue. Noise source/path identification technology applicable to single engine propeller driven aircraft were employed to identify interior noise sources originating from structure-borne engine/propeller vibration, airborne propeller transmission, airborne engine exhaust noise, and engine case radiation. The approach taken was first to conduct a Principal Value Analysis (PVA) of an in-flight noise and vibration database acquired on a single engine aircraft to obtain a correlated data set as viewed by a fixed set of cabin microphones.

Typical two-site storage-based SCR plant models in literature consider NH3 stored in the first site to participate in NH3 storage, NOx conversion and second site to only participate in NH3 storage passively. This paper focuses on quantifying the impact of stored NH3 in the second site on the overall NOx conversion for an ultra-low NOx system due to intra site NH3 mass transfer. Accounting for this intra site mass transfer leads to better prediction of SCR out NH3 thus ensuring compliance with NH3 coverage targets and improved dosing characteristics of the controller that is critical to achieving ultra-low NOx standard. The stored NH3 in the second site undergoes mass transfer to the first site during temperature ramps encountered in a transient cycle that leads to increased NOx conversion in conditions where the dosing is switched off. The resultant NH3 coverage fraction prediction is critical in dosing control of SCR.

Various fire scenarios involving a hydrogen fuel system were simulated to evaluate their associated safety hazards. Scenarios included finite releases of hydrogen with delayed ignition as well as small hydrogen jet-fire releases. The scenarios tested resulted in minimal damage to the vehicle, minimal hazards to the vehicle's surroundings, and no observable damage or hazards within the passenger compartment.

A fire exposure test was conducted on a 72.4 liter composite (Type HGV-4) hydrogen fuel tank at an initial hydrogen pressure of 34.3 MPa (ca 5000 psi). No Pressure Relief Device was installed on the tank to ensure catastrophic failure for analysis. The cylinder ruptured at 35.7 MPa after a 370 kW fire exposure for 6 min 27 seconds. Blast wave pressures measured along a line perpendicular to the cylinder axis were 18% to 25% less the values calculated from ideal blast wave correlations using a blast energy of 13.4 MJ, which is based on the ideal gas internal energy at the 35.7 MPa burst pressure. The resulting hydrogen fireball maximum diameter of 7.7 m is about 19% less than the value predicted from existing correlations using the 1.64 kg hydrogen mass in the tank.

An experimental program was designed to determine friction characteristics between brake pads and metal rotors that could indicate a brake fluid's propensity to cause chatter in wet-brakes. Friction was measured on a bench version of the John Deere wet-brake qualification system. Rotor and pad supports were made very rigid to avoid chatter in the simulator. One type of pad was run on cast-iron and mild steel rotors using two reference oils, one giving unacceptable levels of chatter and the other giving acceptable levels as previously determined in full-scale tests on the Deere system. The outstanding discriminating characteristic was the drop in friction from breakaway of the pad from the rotor. The ratio of the initial drop in the friction coefficient between unacceptable and acceptable oils for all conditions of the testing ranged from 1.7 to 2.0

This paper examines the role of inhalation toxicity of the products of combustion that are generated in post-collision motor vehicle fires by automotive materials used under the hood. Small-scale toxic gas measurements were performed at Southwest Research Institute® (SwRI®) on eighteen components of two of the vehicles that were tested previously at the Factory Mutual Test Center (FMTC). The small-scale toxic gas measurements were obtained under dynamic flow-through conditions in the Cone Calorimeter (ASTM E 1354) and under static conditions in two smoke chamber methods (ASTM E 662 and ASTM E 1995); all methods were supplemented with FTIR gas analysis. Average yields of toxic gases measured in the Cone Calorimeter are comparable to but consistently lower than values reported in the literature for the Fire Propagation Apparatus (ASTM E 2058).

Changing fuel quality, increasingly stringent exhaust emission standards, demands for higher efficiency, and the trend towards higher specific output, all contribute to the need for a better understanding of the ignition process in diesel engines. In addition to the impact on the combustion process and the resulting performance and emissions, the ignition process controls the startability of the engine, which, in turn, governs the required compressions ratio and several of the other engine design parameters. The importance of the ignition process is reflected in the fact that the only combustion property that is specified for diesel fuel is the ignition delay time as indicated by the cetane number. The objective of the work described in this paper was to determine the relationship between the ignition process as it occurs in an actual engine, to ignition in a constant volume combustion bomb.

A novel urea evaporation and mixing device has been developed to improve the overall performance of a urea-SCR system. The device was tested with a MY2007 Cummins ISB 6.7L diesel engine equipped with an SCR aftertreatment system. Test results show that the device effectively improved the overall NO conversion efficiency of the SCR catalyst over both steady-state and transient engine operating conditions, while NH₃ slip from the catalyst decreased.

The primary objective of this study was to compare the performance of “new” plastic fuel tanks vs. “aged” plastic fuel tanks when subjected to the standard fire exposure test described in ECE R34.01, Annex 5 Section 5.0 “Resistance to Fire.” The program also included a comparison of failure modes of plastic vs. metal fuel tanks when subjected to a simulated post-crash pool fire. The “new” tanks were purchased from the OEM suppliers (not weathered or pre-conditioned with fuel). The “aged” tanks were obtained from vehicles that were operated in a warm climate and considered to be weathered and fully conditioned with fuel. Three vehicle types, representing three fuel tank shapes and installations, were evaluated: 1.) “thin profile” tank, typical of front wheel drive cars with the tank mounted on the underbody near the rear seat area and in front of the rear axle; 2.) “square profile” tank, typical of SUV's with the tank mounted behind the rear axle; and 3.)

Comparative abuse tests were performed on commercially available 12 V and 36 V battery designs. Four methods were chosen from SAE J2464 standard, Electrical Vehicle Battery Abuse Testing, March 1999, and modified to apply them to typical-sized automotive batteries. The four tests included a Penetration Test, Crush Test, Radiant Heat Test, and Short Circuit Test. Both the 12 V and 36 V batteries showed minimal reactions to the tests, and there was no significant difference between results of the two designs with respect to the abuse tests performed. It should be stressed however, that this project was limited in scope and was not intended to be a thorough investigation in the batteries safety hazards.

This paper describes a distributed digital process control computer designed for large industrial processing plants that has been applied successfully to laboratory engine testing. Over the past two years several complete systems have been installed and adapted to control engines from 75 kW to over 1800 kW with various dynamometer/generator absorption devices. Control problems encountered, and solutions we have found, are discussed along with the wide range of capabilities this type of system can provide. A short comparison is made between distributed digital control systems and mini-computers, listing advantages and disadvantages of both.

The principles of the magnetic-perturbation method of flaw detection and the Barkhausen noise residual stress measurement method are briefly reviewed. It is suggested that they provide very powerful tools for assuring improved ball bearing performance. The methods are applied for the evaluation of ball bearing races. Typical experimental results are presented along with metallurgical sectioning correlation.