Search Results

An early development vehicle experienced an unusually high rate of windshield breakage. Most breaks were identified as due to impact, but the severity of impact was low. It was reasoned that the windshield should possess a greater level of robustness to impact. Many theories were put forth to explain the breakage data. It was universally agreed that the unusual breakage rate could be due to only one condition, but its source was indefinite. The condition present must be tensile stress. One of three situations were considered regarding its source: 1) the tensile stress was present in the glass after manufacture due to improper annealing; 2) the installation of the windshield into the vehicle body put the glass into stress; 3) some combination of the other two sources. A gray-field polariscope was used to measure the stresses of the windshield from both the manufacturing process as well as the installation in the vehicle.

Adhesive joining is a common autobody subassembly technique especially for outer panels, where visible spot welding is objectionable. To accommodate mass production with the use of certain adhesives very high thermal gradient usually exists, which may result in panel dimensional distortion and variation. The temperature distribution over location and over time are monitored, and its impact to panel dimension is investigated. Experimental results on the effect of the distance between panel and induction coil on the panel temperature is obtained. The thermal induced shape distortion is simulated with a simplified FEA model. The approach to improvement of the induction curing process is discussed.

During the development of a Statistical Energy Analysis (SEA) model, the most important step leading toward higher quality and confidence is the model validation process. In this paper, three different ideal source environments are employed to validate a SEA model of a minivan; diffuse field in a reverberation room, free field in an hemi-anechoic room and single-point excitation by a shaker. The tests were intended to emphasize the air-and structure-borne paths of the model separately. During the reverberation room test, capability of the model to track the design changes was checked by perturbing the configuration of the vehicle in successive steps. Finally, the performance of the validated SEA model is demonstrated by using an operational load case.

The hybrid Finite Element Analysis (hybrid FEA) has been developed for performing structure-borne computations in automotive vehicle structures [1, 2 and 3]. The hybrid FEA method combines conventional FEA with Energy FEA (EFEA). Conventional FEA models are employed for modeling the behavior of the stiff members in a system. Appropriate damping and spring or mass elements are introduced in the connections between stiff and flexible members in order to capture the presence of the flexible members during the analyses of the stiff ones. The component mode synthesis method is combined with analytical solutions for determining the driving point conductance at joints between stiff and flexible members and for defining the properties of the concentrated elements which represent the flexible members when analyzing the stiff components.

A commercial NOx-storage catalyst for gasoline applications containing Ba/CeO2/Al2O3, platinum, palladium and rhodium has been sulfated on the engine bench at 390 and 510°C with a nominal exposure of 1.3 g sulfur/liter catalyst. Lower exposures proved too low to have a notable impact on the catalytic performance. At 390°C the sulfur is completely adsorbed while at 510°C only partial adsorption is being observed. Sulfur is mainly deposited at the catalyst inlet thereby shielding the downstream region. Desulfation on synthetic gas bench at 700°C leads to a partial removal of the sulfur. The residual sulfur is more evenly distributed along the length of the catalyst compared to the sulfur profile in the sulfated catalyst. This causes an improvement of the NOx-activity at the inlet side while the NOx-performance at the outlet side decreases after desulfation.

Sound attenuation and flow loss reduction are often two competing demands in vehicle breathing systems. The present study considers a full vehicle exhaust system and investigates both the sound attenuation and the flow performance of production configurations including the catalyst, the resonator, and the muffler. Dynamometer experiments have been conducted with a firing Ford 3.0L, V-6 engine at wide-open throttle with speeds ranging from 1000 to 5000 rpm. Measurements including the flow rates, the temperatures and the absolute dynamic pressures of the hot exhaust gases at key locations (upstream and downstream of every component) with fast-response, water-cooled piezo-resistive pressure transducers facilitate the calculation of acoustic performance of each component, as well as the determination of flow losses caused by these elements and their influence on the engine performance.

DaimlerChrysler and Mechadyne have undertaken a piece of work to investigate the opportunities for improving the operation of light duty diesel engines using variable valve timing. The very high compression ratios used in this type of engine make it essential to be able to alter the valve open periods to affect exhaust valve opening and intake valve closing, whilst leaving the valve motions largely unchanged around overlap top dead centre to avoid valve to piston contact. This paper presents an overview of the design solution, a description of the simulation model used, performance and economy data predicted by the model and a discussion of other areas of opportunity where improvements may be possible.

The introduction of vehicle emission and fuel economy standards (CO2) accelerates the introduction of new platform and powertrain combinations into the market place. All of these combinations will require unique exhaust gas aftertreatment systems that comply with the current emission legislation. The optimization of each unique aftertreatment solution requires the proper application of catalyst technologies at the lowest PGM concentrations. The optimization process needs to be fast, reliable, realistic and cost attractive. It is arguable that performing the aftertreatment optimization on a chassis dynamometer is variable, time consuming and expensive. This work demonstrates how a synthetic gas bench (SGB) can be used to simulate stoichiometric engine emissions and aftertreatment performance. The SGB procedure duplicates the vehicle NEDC engine-out emissions and catalyst heat-up profiles.

Within the framework of the French research program PREDIT, a study was undertaken by ADEME, IFP, LGRE, PSA Peugeot Citroën and Umicore, whose main objective was a better understanding of the NOx storage and reduction phenomena on an aged, sulfated and desulfated NOx-trap. The target of this work was to use the information on catalyst working conditions to optimize catalyst management for a gasoline direct injection engine. The catalysts were characterized on both engine and synthetic gas benches. Aging and poisoning phenomena were studied and a variety of different chemical analytical tools were used. The behavior of two different thermally aged cores was investigated under rich conditions on a synthetic gas test bench. The dependence of the NOx regeneration efficiency of the traps is reported for several operating parameters, including reductant concentrations, durations of the rich pulse and trap loadings.

Failure loads of spot welds are investigated under static and impact loading conditions. A test fixture was designed and used to obtain maximum loads of spot welds under a range of combined opening and shear loads with different loading rates. Optical micrographs of the cross sections of spot welds before and after failure were obtained to understand the failure processes under various loading rates and different combinations of loads. The experimental results indicate that under nearly pure opening loads, the failure occurs along the nugget circumferential boundary. Under combined opening and shear loading conditions, the failure starts from the tensile side of the base metal near the nugget in a necking/shear failure mode. The effects of sheet thickness and combined load on the load carrying behavior of spot welds are investigated under static and impact loading conditions based on the experimental results.

The relationship of slip resistance (or coefficient of friction) to safe climbing system maneuvers on high profile vehicles has become an issue because of its possible connection to falls of drivers. To partially address this issue, coefficients of friction were measured for seven of the more popular fabricated metal step materials. Evaluated on these steps were four types of shoe materials (crepe, leather, ribbed-rubber, and oil-resistant-rubber) and three types of contaminant conditions (dry, wet-water, and diesel fuel). The final factor evaluated was the direction of sole force application. Results showed that COF varied primarily as a function of sole material and the presence of contaminants. Unexpectedly, few effects were attributible to the metal step materials. Numerous statistical interactions suggested that adequate levels of COF are more likely to be attained by targeting control on shoe soles and contaminants rather than the choice of a particular step material.

In a consortium of European industrial partners and research institutes, a combination of industrial development and scientific research was organised. The objective was to improve the catalytic NOx conversion for lean burn cars and heavy-duty trucks, taking into account boundary conditions for the fuel consumption. The project lasted for three years. During this period parallel research was conducted in research areas ranging from basic research based on a theoretical approach to full scale emission system development. NOx storage catalysts became a central part of the project. Catalysts were evaluated with respect to resistance towards sulphur poisoning. It was concluded that very low sulphur fuel is a necessity for efficient use of NOx trap technology. Additionally, attempts were made to develop methods for reactivating poisoned catalysts. Methods for short distance mixing were developed for the addition of reducing agent.

A Robust Engineering experiment was performed to determine the effects PGM loading and placement on the FTP emissions of a 4 cylinder 2.4L and two 8 cylinder 4.7L vehicles. 1.3L catalytic converters were used containing a front and rear catalyst of equal volume. The experiment is defined by a Taguchi L-8 array. Eight different combinations of catalyst PGM loadings were aged and evaluated. Results show that nmHC and NOx emissions are predominately affected by the PGM loading of the front catalyst. The rear catalyst is insensitive to either Pt or Pd which can be used at low concentrations. Results also compare the benefits of Pd and Rh to reduce emissions. Confirmation runs suggest that significant reductions in PGM cost can be achieved over baseline designs.

The future of diesel-engine-powered passenger cars and light-duty vehicles in the United States depends on their ability to meet Federal Tier 2 and California LEV2 tailpipe emission standards. The experimental purpose of this work was to examine the potential role of fuels; specifically, to determine the sensitivity of engine-out NOx and particulate matter (PM) to gross changes in fuel formulation. The fuels studied were a market-average California baseline fuel and three advanced low sulfur fuels (<2 ppm). The advanced fuels were a low-sulfur-highly-hydrocracked diesel (LSHC), a neat (100%) Fischer-Tropsch (FT100) and 15% DMM (dimethoxy methane) blended into LSHC (DMM15). The fuels were tested on modern, turbocharged, common-rail, direct-injection diesel engines at DaimlerChrysler, Ford and General Motors. The engines were tested at five speed/load conditions with injection timing set to minimize fuel consumption.

Barrier impacts are routinely used to estimate the impact response of vehicles in vehicle-to-vehicle crashes. One area of investigation is the detection of the secondary energy absorbing structures provided for under-/over-ride mitigation as a result of increased structural engagement -- improved geometric compatibility. The flat rigid barrier and the Transportation Research Laboratory’s (TRL) full width honeycomb barrier are commonly considered. In the present study, a vehicle-to-vehicle impact that exhibited no under-/over-ride condition was compared to finite element analysis of vehicle impacts to the two different barriers in order to evaluate their ability to detect the secondary energy absorbing structure. This study demonstrates that the rigid barrier and the TRL barrier yield similar quantitative information with regard to vehicle-to-vehicle crashes.

Catalyzed diesel particulate filter systems have now been successfully introduced and implemented in Europe. In the meantime, automotive manufacturers are working on the second generation of catalytic filters with the aim of reducing the overall system costs. In particular savings in precious metal costs are focussed by the use of highly-active catalysts which are stable at high temperatures. A possible approach here is the implementation of oxidation catalysts and catalytically coated filters based on platinum and palladium. In this context, the functio-nality of platinum/palladium-based, catalyzed filters was investigated by numerous measurements on a synthetic gas and an engine bench as well as by vehicle tests on a roller dynamometer. The HC/CO oxidation activity, the poisoning resistance towards sulfur and the desulfurization capability, the exothermic behaviour due to the conversion of subsequently injected hydrocarbons and the NO2 formation potential were examined in detail.

In order to match catalyst OBDII conditions the common procedure is oven aging with air, which is not suitable for complete converter systems due to mantle corrosion. The goal was, therefore, to find an alternative procedure to ensure a defined catalyst aging that would match 1,75 times the emission standard and is also good for SULEV. The new procedure currently being developed allows the aging of metal and ceramic catalysts as well as complete catalyst systems. The paper will present the aging process, emission data of fresh and aged catalysts and the feedback to the test car OBDII system.

In this paper we report on a new state of the art diesel LNT (Lean NOx Trap) formulation that is designed to comply with North American emission legislation for diesel passenger cars. Improved performance and durability is demonstrated in an aging study using hydrothermal furnace aging and a prolonged procedure behind the engine consisting of repeated cycles containing sulfur exposure, desulfation and simulated regeneration of a diesel particulate filter. The improved barium based technology shows an increased thermal stability in terms of upper not-to-exceed temperature of at least 50°C. Our data show that potassium based technologies can represent a viable solution for certain applications that require extremely high NOx-conversions at temperatures above 500°C. Potassium based technologies with improved anchoring of the alkali metal show significant reduction in potassium loss to the exhaust gas.

Although biomechanics models can predict the stress on the musculoskeletal system, they cannot predict how the muscle load associated with exertion is perceived. The short-term goal of the present study was to model the perception of effort in lifting and reaching tasks. The long-term goal is to determine the correlation between objective and subjective measures of effort and use this information to predict fatigue or the risk of injury. Lifting and reaching tasks were performed in seated and standing situations. A cylindrical object and a box were moved with one hand and two hands, respectively, from a home location to shelves distributed in the space around the subject. The shoulder and torso effort required to perform these tasks were rated on a ten point visual analog scale.

Failure behavior of spot welds is investigated under impact loading conditions. Three different impact speeds were selected to test both HSLA steel and mild steel specimens under combined opening and shear loading conditions. A test fixture was designed and used to obtain the failure loads of spot weld specimens of different thicknesses under a range of combined opening and shear loads with different impact speeds. Accelerometers were installed on the fixtures and the specimens for investigation of the inertia effects. Optical micrographs of the cross sections of failed spot welds were obtained to understand the failure processes in both HSLA steel and mild steel specimens under different combined impact loads. The experimental results indicate that the failure mechanisms of spot welds are very similar for both HSLA steel and mild steel specimens with the same sheet thickness. These micrographs show that the sheet thickness can affect the failure mechanisms.