Search Results

Generally, automobiles have many performance requirements for comfort, of which noise, vibration and harshness are very important. Toyota Motor Corporation equipped several 2003 models with the second-generation Electronically Controlled Brake system (ECB2). These ECB2 actuator units adopted a new structure that reduced pumping noise by controlling the skew phenomena of needle roller bearings. Normally, needle roller bearings are advantageous over other bearings in cases where a large force is loaded on bearings, because the contact areas can be made larger. However, a thrust force arises from skew phenomena because of minute clearances among the component parts of needle roller bearings. As a result, axial vibration of the bearing shaft sometimes occurs due to the thrust force. This paper explains how the thrust force generated from the skew phenomena of needle roller bearings occasionally affects the pumping vibration level of equipped machinery such as the brake actuator unit.

The purpose of this study is to propose braking characteristics that are easy for drivers to handle in a system in which braking and driving operations are performed by hand. Genetic algorithm optimization of braking characteristics showed that the best deceleration tracking was achieved by an FG diagram with a logarithmic function shape. In contrast, the slope of the optimal FG diagram tended to decrease as the driver's proportional gain increased.

In the studies of disc brake squeal, the vibration modes on squealing were measured, and calculated [1, 2 and 3]. By those results to the disk rotor, it is clear that the specific type of the modes affect the squeal generation. It is not clear whether mounting bracket mode shapes contribute to squeal, because the mounting bracket mode shapes cannot be classified in the same way as the rotor mode shapes. In this paper, by using FEM modal analysis the vibration modes of the mounting bracket are classified systematically. And by adopting this classification to the vibration mode of mounting on squealing, it is confirmed that the specific type of modes of mounting affect the squeal generation.

The purpose of this research is to clarify how damping characteristics of Under Layer (hereafter “UL”) material in the brake pads (hereafter “PAD”) influences brake squeal noise performance. In this study, UL material structure and dynamic viscoelasticity, for two different types of UL formulations are investigated. In addition, PAD damping ratio and squeal noise performance for multiple UL formulations are verified. As a result, the raw material orientation is determined based on manufacturing method, and it causes the UL material’s anisotropic properties. Dynamic viscoelasticity are dependent on the direction in which they are measured. In particular, the loss modulus, which is the damping element of dynamic viscoelasticity, is higher in the direction of the raw material orientation for the high damping and high stiffness UL formulation. In addition, it was confirmed that this loss modulus in the direction of the raw material orientation is effective for bending vibration.

This paper describes methods to attain a low cost tire pneumatic pressure monitor. We already established two kinds of algorithms for indirect detection of under-inflated tires without requiring any air pressure sensors. One method is to use a disturbance observer and the least mean square method. The other method is to compare the loaded radii of the tires. We have developed an algorithm that reduces the number of calculations needed, while maintaining a relatively small program size, and realized a tire pneumatic pressure monitor that does not require any hardware cost, by incorporating it into the program for the antilock brake system (ABS).

A new type of electric brake booster, which can control brake pedal feeling completely with software, has been developed to explore how a brake system can be used to differentiate and personalize vehicles. In the future, vehicles may share an increasing amount of hardware and rely more heavily on software to differentiate between models. Car sharing, vehicle subscriptions, and other new business models may create a new emphasis on the personalization of vehicles that may be achieved most cost effectively by using software. This new brake booster controls the brake pedal force and brake pressure independently based on the brake pedal stroke so that the pedal feeling is completely defined by software. The booster uses two electric motors and one master cylinder. One electric motor controls the pedal force and provides an assist force that amplifies the force that the driver applies to the brake pedal.

Electronic stability control (ESC) is becoming a standard technology in passenger cars, and because of its effectiveness in reducing serious traffic accidents, its use is spreading to commercial vehicles. ESC is activated by comparing the target vehicle behavior, which is analyzed based on driver operation, with the actual vehicle behavior, which is detected by onboard sensors. The target vehicle behavior is analyzed with an initial steer characteristic (such as a vehicle stability factor Ks) representing a vehicle turning characteristic (understeer, neutral steer, or oversteer). Because Ks changes depending on the payload loading states (such as vehicle mass and location of center of gravity), it varies considerably for commercial vehicles. We analyzed the influence of error in Ks on ESC performance and established a method for the online estimation of Ks. ESC includes the restriction functions of oversteer and understeer.

The prevention of brake squeal is a significant task in brake development, because brake squeal is bothersome to users and consequently reduces a vehicle's commercial value. Due to the progress made by researchers in their efforts to gain insight into the mechanisms and causes of brake squeal, the number of brake squeal complaints has declined. However, brake squeal can appear long after the vehicle is produced, without any early sign. In order to maintain long-term high satisfaction among the vehicle owners, it is important to find the factors that create a gradual increase in the occurrence of brake squeal. In this study, we focus on the stiffness factor of brake pads. Also, brake-pad wear due to braking is virtually impossible to completely eliminate. Here, we examine the correlation between pad stiffness and squeal occurrence. This study presents experimental and analytical results of the influence of pad surface texture on disc brake squeal.

A new concept of an electromagnetic torque converter for hybrid electric vehicles is proposed. The electromagnetic torque converter, which is an electric system comprised of a set of double rotors and a stator, works as a high-efficiency transmission in the driving conditions of low gear ratio including a vehicle moving-off and as a starting device for an internal combustion engine. Moreover, it can be used for an electric vehicle driving as well as for a regenerative braking. In this concept, a high-efficiency drivetrain system for hybrid electric vehicles is constructed by replacing a fluid-type torque converter with the electromagnetic torque converter in the automatic transmission of a conventional vehicle. In this paper, we present the newly developed electromagnetic torque converter with a compact structure that enables mounting on a vehicle, and we evaluate its transmission efficiency by experiment.

Brake pads are composite materials made from dozens of ingredients intended to simultaneously satisfy various performances such as brake effectiveness, wear, noise and vibrations. For this reason, the friction phenomena that occur during braking are complicated. It is important to clarify the friction phenomena, but that is not easy because the associated complexities as mentioned above. We looked to acoustic emission (AE) as an online evaluation method of friction phenomena. AE is a non-destructive testing method that measures elastic stress waves caused by the deformation and fracturing of materials. In fact, it has been reported that the difference between abrasive wear and adhesive wear of a metal can be identified from the change in the frequency spectrum of AE signals. In this study, we verify whether differences in the friction phenomena of brake pads are detectable by the AE method. Three kinds of brake pads were used in the experiments.

To solve various environmental problems, fuel-efficient vehicles that reduce CO2 emissions as well as exhaust gas emissions have been developed. In such vehicles, a regenerative brake is used to further reduce fuel consumption. Because the market size for such vehicles is expanding, a brake system is required that can be used in a wide range of vehicles extending from internal combustion engine vehicles (ICEVs) to electric vehicles (EVs). In addition, issues such as deceleration fluctuation and brake pedal fluctuation arise because the regenerative brake force is dependent on the vehicle speed. This paper presents a brake system configuration and its element technologies that can replace existing brake systems in different vehicles ranging from ICEVs to EVs. The proposed system can realize a regenerative cooperative brake not only by replacing the brake booster unit but also without replacing the modulator.

In anticipation of the increased needs to further reduce exhaust gas emissions and improve fuel consumption, a new brake-by-wire system called an “Electronically Controlled Brake” system (hereafter referred to as “ECB”) has been developed. With this brake system, which is able to smoothly control the hydraulic pressure that is applied to each of the four wheel cylinders on an individual basis, functional enhancements can be added by appropriately modifying its software. This paper discusses the necessity of the ECB, the system configuration, and the results of its application on hybrid vehicles.

HEV and EV markets are in a rapid expansion tendency. Development of low-cost regenerative cooperation brake system is needed in order to respond to the consumers needs for HEV and EV. Regenerative cooperation brake system which HEV and EV are generally equipped with has stroke simulator. We developed simple composition brake system based on the conventional ESC unit without the stroke simulator, and our system realized a low-cost regenerative cooperation brake. The key technologies are the quiet pressurization control which can be used in the service application, which is to make brake force depending on brake travel, by gear pump and the master cylinder with idle stroke to realize regenerative cooperation brake. Thanks to the key technologies, both the high regenerative efficiency and the good service brake feeling were achieved.

The use of hybrid, fuel cell electric, and pure electric vehicles is on the increase as part of measures to help reduce exhaust gas emissions and to help resolve energy issues. These vehicles use regenerative-friction brake coordination technology, which requires a braking system that can accurately control the hydraulic brakes in response to small changes in regenerative braking. At the same time, the spread of collision avoidance support technology is progressing at a rapid pace along with a growing awareness of vehicle safety. This technology requires braking systems that can apply a large braking force in a short time. Although brake systems that have both accurate hydraulic control and large braking force have been developed in the past, simplification is required to promote further adoption.

In recent years, there has been a growing need for excellent automobile safety. The number of vehicle with active safety systems such as ABS, Brake Assist and VSC (Vehicle Stability Control) is dramatically increasing. A current brake control systems tend to generate activating noise and uncomfortable brake pedal feeling, which they have to restrain its positive use during ordinary braking. To improve this point, a new brake control system has been developed. This paper introduces the configuration, functions and effects of the system. The new hydraulic modulator adopts a gear pump (trochoid pump) and linear solenoid valves. This allows the modulator to be controlled silently and smoothly. As a result, it becomes possible to apply hydraulic pressure in the normal operating range at any time and a high level of performance is realized. Several new benefits were added to the current control system.

We expect to reduce exhaust gas emissions further and improve fuel consumption, by developing a new brake system (called brake-by-wire system) to control the friction brake force and the regenerative brake force of the two motors, one each at front and rear axle. Within this new system we developed the new technology listed below. 1 To compensate the changes of the regenerative brake force of front and rear motors, the friction brake force is controlled by adjusting the wheel cylinder hydraulic pressures. 2 The pressure of each wheel cylinder is controlled by linear solenoid valves. So the hydraulic pressure of wheel cylinders is controlled individually and smoothly. This brake system also operates ABS, VSC, TRC functions. The vehicle stability performance is improved by controlling the braking and driving torque of two motors and also controlling the friction brake torque cooperatively.

Toyota Motor Corporation has already designed and developed vehicle brake control systems for relatively low speed off-road driving, such as Downhill Assist Control, Hill-start Assist Control and Active Traction Control. Though off-road utility is improved by virtue of these systems, in specific situations actual performance still depends on driving technique since the driver is required to control the accelerator pedal. Toyota has integrated these existing systems, and developed a new driving technology for off-road driving called “Crawl Control.” Crawl Control automatically modulates brake torque and drive torque to help keep the vehicle speed constant and slow. Unskilled drivers can thereby attain improved capabilities in places where high-level driving techniques are required. This system also reduces the effort required to control the accelerator and the brake pedal. This paper presents a new control algorithm for the realization of this Crawl Control system.

A Rear Cross Traffic Auto Brake (RCTAB) system has been developed that uses radar sensors to detect vehicles approaching from the right or left at the rear of the driver’s vehicle, and then performs braking control if the system judges that a collision may occur. This system predicts the intersecting course of approaching vehicles and uses the calculated time-to-collision (TTC) to control the timing of automatic braking with the aim of helping prevent unnecessary operation while ensuring system performance.

A new active rear steer (ARS) system has been developed. ARS is an electric four wheel steering system controlled by new logic(designed by H∞-μ synthesis) which maintains good control performance even if the vehicle parameters and /or road surface conditions are changed. ARS control is a typical technology to prevent vehicle side -slip in linear region of tire characteristic. This system offers easy control and reduces vehicle behavior of yawing motion before approaching critical limit. By combining ARS and vehicle stability control (VSC), it is possible to support driving precisely from normal driving to excessive driving. This paper describes the details of this new system which has been installed on 1997 model TOYOTA ARISTO for practical use in JAPAN.

This study aims to incorporate the dynamic stiffness of pads into the finite element method (FEM) used for brake design in order to improve the accuracy of FEM analyses. In the first step, the vibration caused by a disk brake squeal is simulated in order to measure the dynamic stiffness of the brake pads. We then compare this result with the static stiffness result obtained from a past static compressive strain and show that these different modes of stiffness have different characteristics. The dynamic stiffness of the pad is higher than the static stiffness and is greatly dependent on pressure load. The next step is to show, from the squeal experiments using a simple squeal tester and FEM analysis, that it is dynamic stiffness and not static stiffness of the pads that correlates to squeal.