Search Results

A very difficult problem exists regarding windshield shape, and that is to create a balance between aerodynamics and optical distortion. To assist in solving this problem, this study, concerning the characteristics of visual perception for the optical distortion when drivers receive visual information through a windshield, was carried out. In this study, the windshield area was divided into 4 zones from the viewpoints of the level of drivers' fixation frequency and types of objects observed. Distortion was defined as the gap angle ( distortion angle ), which crossed the lines of a grid board with and without a windshield, and distortion angles were measured on a total of 4 windshields. Four drivers indicated areas in each windshield in which they felt the area was distorted. As a result, the thresholds of optical distortion were shown as a function of the horizontal and vertical distortion angles by discriminatory analysis.

In order to correspond to the exhaust emissions regulations that become severe every year, more advanced engine control becomes necessary. Engine engineers are concerned about the Hydrocarbons (HCs) that flow through the air-intake ports and that are difficult to precisely control. The main sources of the HCs are, the canister purge, PCV, back-flow gas through the intake valves, and Air / Fuel ratio (A/F) may be aggravated when they flow into the combustion chambers. The influences HCs give on the A/F may also grow even greater, which is due to the increasingly stringent EVAP emission regulations, by more effective ventilation in the crankcase, and also by the growth of the VVT-operated angle and timing, respectively. In order to control the A/F more correctly, it is important to estimate the amount of HCs that are difficult to manage, and seek for suitable controls over fuel injection and so on.

In the field of automotive body electronic control such as control of door locks, power windows, and wipers, there is a growing need of multiplexing communication to reduce the amount of wire harnesses. To meet this need, we developed a multiplexing communication protocol particularly suited to the body electronic control. Based on the developed protocol, we designed a communication control IC and a simple driver/receiver circuit with a few discrete components. The bus access method of the communication is the CSMA/CD with nondestructive bit arbitration, and its bit rate is 5 kbps. Its transmission media is a single wire. The communication IC has a multiplexing control block and a serial I/O block for an interface with a host CPU. It was fabricated using CMOS technology and has a chip of 2.6mm x 3.0mm in size that contains about 5,000 transistors. The driver/receiver circuit consists of one transistor, one capacitor and several resistors.

A new experimental method, that enables to estimate the body and driveline sensitivity to unit transmitting error of a hypoid gear for automotive rear axle gear noise, has been developed. Measurements were made by exciting the tooth of the drive-pinion gear and that of the ring gear separately using the special devices designed with regard to simulation of acceleration and deceleration. The characteristic of this method is to estimate the forces at the contact point of the gears. Estimation of these forces is carried out under the condition that the higher stiffness is provided by the tooth of the drive-pinion gear and that of the ring gear, compared with the stiffness of the driveshafts and that of the propeller shaft etc., and relative angular displacement of the torsional vibration between the teeth of the drive-pinion gear and those of the ring gear is constant.

In recent years, a number of different Blind Spot Monitor (BSM) systems have become more and more popular in North American automotive market. The BSM system advises the driver of vehicles travelling in adjacent lanes when these vehicles are also in the driver's outside rearview mirror blind spots. Similarly, when the vehicle is backing up from a parking spot, cross-traffic vehicles can be in the driver's outside mirror blind spots. In this situation, the Rear Cross Traffic Alert (RCTA) system alerts the driver when the driver shifts the vehicle in the reverse gear and there are approaching cross-traffic vehicles. The benefits of RCTA system was presented by [1]. The RCTA alert studied in this paper is given by playing an audible sound and by flashing the outside mirror indicators. The RCTA and BSM systems share the same vehicle sensors and most of their vehicle components.

Sintered silicon nitride, particularly in structural ceramics, has superior properties such as low weight, heat resistance, wear resistance, etc. It is already being applied to automobile engine parts such as the swirl chamber and the turbine rotor. In recent years, the strength of silicon nitride has shown to be above 1000MPa. This has been achieved through advances in manufacturing technology such as materials powder, forming, sintering and so on. But the silicon nitride is easily damaged during grinding because it has less fracture toughness than metal. Consequently, the inherent strength of the material is not demonstrated in the actual products presently produced. It is assumed that the main cause of strength reduction is microcrack. In ordinary grinding methods, the length of microcrack has been estimated at approximately twenty micrometers by fracture mechanics analysis.

So far in conventional automotive meter, reflection of the incident light on a cover glass is prevented by a hood and a curved cover glass. Anti-reflection coating (hereafter abbreviated as AR coating) on the surface of cover glass can offer a meter without the hood. Thin films of AR coating are uniformly deposited on a large polymethylmethacrylate substrate in an ambient atmosphere by sol-gel dip coating and cured at low temperature. The AR coated panel shows a very low reflectance. In addition, the AR coating has a high reliability for the instrument panels of automobiles. The AR coating meter offers new instrument panel design for Toyota Prius.

Airflow effect is one of the important functions demanded of a rear spoiler. It helps prevent mud or dust from swirling up behind the running vehicle, or in the case of driving in the rain or snow, helps prevent rain or snow from adhering to the rear window. During the design process, we often decide on the shape of a spoiler in a relatively short time, focusing primarily on its appearance. Therefore, we established a design method using the recently developed computational fluid dynamics (CFD) to determine the central cross sectional shape of a spoiler that produces a desired airflow effect. We verified its effectiveness through testing.

Damping materials are used to control vehicle noise and vibration. This paper discusses techniques to design effective vibration damping treatments. Vibration and damping characteristics of vehicle panels with viscoelastic layers have been investigated. As a result of the investigation, new parameters have been contrived. Applying the parameters to basic theories, it has become possible to estimate the damping efficiency of complicated body panels and to design the panel structures to maximize the damping effect. Criteria for the determination of the body panel specifications and methods to control resonant frequencies of vehicle panels are also presented. This paper concludes with applications of the damping techniques to reduce interior noise.

1G engine series consists of four types of 2-liter, in-line, 6-cylinder gasoline engines for passenger cars, with different performance characteristics to meet diversified market demands. These engines are already put into mass production. The original engine - 1G-EU - is a compact and light weight 2-valve OHC engine with the maximum power 77 kW/5200 rpm. The 1G-GEU is a 4-valve DOHC engine developed on the basis of the 1G-EU engine, with a higher performance and a higher power of 103 kW/6200 rpm. The 1G-GZEU is a mechanical supercharging type engine based on the 1G-GEU, with a remarkably improved performance in the low and medium engine speed ranges, and the highest power of 110 kW/6000 rpm. The 1G-GTEI! is a turbocharging type engine also based on the 1G-GEU, with a markedly improved performance in the medium and high speed ranges, and the high power of 136 kW/6200 rpm. A number of new technologies were introduced on development of these engines.

Recently, there has been a tendency of high power and high speed in automotive engines. In addition they have been also required high reliability. And engine bearings have been required to be advanced in wear resistance as well as seizure resistance. Therefore, copper-lead alloy bearings with overlay, which have better seizure resistance, have been widely used for high speed engines up to the present. But it becomes very important for them to advance the overlay wear resistance. In this paper, the composite overlay is mainly researched to improve wear resistance regarding kind of hard particles and their amounts in the overlay.

Filiform corrosion phenomenon and its prevention method for 5000 series aluminum alloy sheet have been investigated. The painted aluminum alloy sheets were subject significantly to filiform corrosion caused by formation of a mottled and coarse zinc phosphate film during chemical conversion process. On the other hand, galvanized aluminum alloy sheet showed an uniform and fine phosphate film in a brief time and the filiform corrosion resistance was improved markedly. The test results of press-forming and corrosion for the prototype engine hoods made of this newly developed galvanized sheets have revealed a good formability and an excellent filiform corrosion resistance.

This paper describes the development of an innovative AWD system called Dynamic Torque Vectoring AWD for all-wheel drive (AWD) vehicles based on a front-wheel drive configuration. The Dynamic Torque Vectoring AWD system helps to achieve high levels of both dynamic performance and fuel efficiency. Significant fuel economy savings are achieved by using a new compact disconnection mechanism at the transfer and rear units, which prevents any unnecessary rotation of the propeller shaft. In addition, the system is also capable of independently distributing torque to the rear wheels by utilizing electronically controlled couplings on the left and right sides of the rear differential. This greatly enhances both on-road cornering performance and off-road driving performance.

The liquid crystal day & night mirror with excellent reflective characteristics has been developed. The day & night mirror using Guest-Host liquid crystal devices improves the performance of rear view mirrors. Effects of primary factors on reflective characteristics of the liquid crystal day & night mirror have been investigated. Results are as follows. (1) The reflective characteristics at wavelength of about 555 nm are important for the selection of liquid crystals and dichroic dyes. (2) The reflective characteristics are improved by decreasing the reflectivity of glass substrate. (3) The reflective characteristics are improved by increasing the reflectivity of reflector.

This paper describes the development of one-piece die cast magnesium steering wheel frame for a steering wheel incorporating an air bag system. The light weight magnesium frame was designed to have proper stiffness, strength and characteristics of energy absorption. Magnesium alloys with various aluminum contents were tested, and AM60B alloy was selected because of its favorable properties of strength and elongation. New manufacturing techniques, for example, a vacuum hot chamber die casting system and a surface defect inspection system were developed in order to produce high quality castings. The characteristics of energy absorption were evaluated in the laboratory and on actual vehicle crash test, and the results were satisfactory. The magnesium steering wheel frame is about 45% (550g) lighter than the steel one. It has been in production in Toyota passenger cars with driver side air bags.

Toyota Motor Corporation has mass-produced turbochager with sillicon nitride ceramic rotors. A moment of inertia was reduced by 60% using ceramic rotor which improved turbochager response. The ceramic rotor was joined to metal shaft by new method which compensated problems in both shrink fitting and active brazing methods. They are generals for mechanical and chemical techniques, respectively. There still exist the following disadvantages. It is quite severe to controll the clearance of shrink fitting to obtain the reliability of the joint. The shaft may be loosened at high temperature with a small shrink-fit interference. The large shrink-fit interference could result in a failure of ceramic shaft due to large stress. Those may require a machinig accuracy with micron meter order of surface roughness which, leads to high cost.

This paper contains an explanation of a Multiplex Wiring System with Optical Data-Link for cars, which has been installed in the Toyota “Century” since 1982. In this system, a total of 64 signals related to door wiring are transmitted in a multiplex fashion, and the number of wires from the front right-hand door to the interior could be reduced from 46 wires, which were used with conventional wiring techniques, to 10 wires including 2 plastic optical fibers. This system also has various control functions which includes a door-lock control function. In order to give high reliability to this system, we have developed a new optical data-link as well as a new custom micro-computer. And in the automobile industry, such a large scale multiplex wiring system having high reliability is very innovative in our opinion and will surely have a large impact in the future.

In automotive plastic parts, bumpers are rather bigger parts and easy to be detached. And there is growing need to develop bumpers recycling technology. Now we developed the recycling technology for waste painted Super Olefin Polymer (SOP) bumpers from car dealers in production. This technology consists of discriminating from the repair in market by dyeing, and of melting SOP resin and hydrolysis of the paint film which are carried out simultaneously in a twin-screw extruder Reactive Processing System.

In the present social environment, automobile demands further reduction of fuel consumption and light weight. Now that the reduction of vehicle weight is being pursued, even a slight looseness in each element of an automobile may become a source of vibration and noise due to the lowered rigidity of such an automobile. The quietness of vehicles is urged, spline backlash in the spline mechanism exhibits a problem in some cases. A propeller shaft, a part of the automobile driving system, also has a sliding spline mechanism as shown in Fig. 1. Such a propeller shaft is required to have functions of transmitting high torque driving forces, and absorbing the variation of the vehicle driveline overall length at the same time. Vibration and noise are apt to occur if when torque is applied, there is a significant balance fluctuation or great sliding resistance due to spline backlash.

One of the key elements of vehicle safety requires a constantly uninterrupted visible view especially during unexpected weather conditions. Our present development of a light reflection type rain sensor is a key device of our automatic windshield wiper system. The design concept of the sensor is based on the quantification on both detected rainfalls and wiping modes in order to match the wiping mode in an operator's mind by optimizing the optical sensing system and establishing an algorithm for controlling wiping. In addition, auto-initialization of the system has been achieved first in the world.