Search Results

In order to develop the valve rocker arm material for the new type engine, we investigated various materials whose chemical compositions were selected using 30% chromium cast iron, which had shown good results in screening evaluation tests, as the basis. High chromium cast irons are well known for their abrasive wear resistance, but it has been very difficult to apply them for use as rocker arm material because their machinability is very poor, and because it is difficult for them to have a regular microstructure. In this paper, both the manufacturing method for the rocker arm which decreases the disadvantages that high chromium cast iron have and the rocker arm material best suited for this method are described.

The automobile industry currently faces many challenges which may greatly impact on its foundry operations. One of these challenges, consumers'' demand for greater fuel efficiency, can be met by reducing the weight of castings used in automobiles, and minimizing engineering tolerances. In answer to this particular demand, engine foundries have begun to either produce cylinder blocks or other castings with aluminum rather than cast iron. However, if a reduction in weight (thin wall and near-net shaping) can be realized with cast iron, there would be numerous merits from the perspective of cost and compactness and there would be much more flexibility in automotive parts design.

This research developed a new measurement technology for thermal analysis of the heat radiation from a hybrid transaxle case surface to the air and improved the heat radiation performance. This heat flux measurement technology provides the method to measure heat flux without wiring of sensors. The method does not have effects of wiring on the temperature field and the flow field unlike the conventional methods. Therefore, multipoint measurement of heat flux on the case surface was enabled, and the distribution of heat flux was quantified. To measure heat flux, thermal resistances made of plastic plates were attached to the case surface and the infrared thermography was used for the temperature measurement. The preliminary examination was performed to confirm the accuracy of the thermal evaluation through heat flux measurement. The oil in the transaxle was heated and the amount of heat radiation from the case surface was measured.

This paper describes an analysis of the rise in timing belt temperature occuring under high engine speed operation that was made to establish the cause of heat deterioration of the belt materials. Surface temperatures of the belt were accurately measured by correcting thermo-vision detected radiations to eliminate environmental radiation. The temperature profile of a belt cross-section was obtained by a specially developed thermo-couple device. The experimental results indicated that heat generated by the belt contributes significantly to the temperature rise and that the primary cause of the heat generation is bending hysteresis of the belt cords. In addition, a description is made of a method of calculating the rate of heat generation in the belt. In this simulation method, the energy dissipated as heat is calculated from the bending strains and loss moduli of the belt materials. Calculated results were found to agree well with experimental results.

This paper describes application of sintered silicon nitride to the swirl lower-chamber in order to improve performance of turbocharged diesel engines. Various stress analyses by finite element method and stress measurements have been applied to determine the design specifications for the component, which compromise brittleness of ceramic materials. Material development was conducted to evaluate strength, fracture toughness, and thermal properties for the sintered bodies. Ceramic injection molding has been employed to fabricate components with large quantities in the present work. Quality assurance for the components can be made by reliability evaluation methods as well as non-destructive and stress loading inspections. It is found that the engine performance with ceramic component has been increased in the power out put of 9PS as compared to that of conventional engines.

A precise control system for a molten ferrous alloy temperature above 1700 K after the completion of induction melting has been developed in order to produce high quality casting parts for automobiles. In this system, the molten ferrous alloy temperature is measured just one time by a disposable thermocouple after the melting. The system predicts the temperature transition after the measurement using an original thermal model, and adjusts the supplied electric power to the furnace automatically according to the predicted temperature. Using this thermal model, the system has attained control deviations within ±5K under the following temperature controls, and contributed to the quality control of casting parts and the energy-saving during furnace operations. Casting temperature for a cast-steel of 1813 K in a 300 kg capacity high-frequency induction furnace on the “Toyota Vacuum Casting Process”.

The deactivation process of automotive catalysts by lead and phosphoruos were studied. The accelerated poisoning test were performed. The activity evaluation and characterisation of poisoned pellet oxidation catalysts showed the following origin of poisoning deactivations. Lead interacts with active materials and phosphorus covers over catalysts to reduce these catalytic performance. In the case of phosphorus and lead co-existence, the activity decreases rapidly because leadphosphate plugges pores of the support. In monolithic catalysts, highly axial distributions of poisons was obserbed. This characteristic distribution is advantageous for the durability of the catalyst.

This paper presents the numerical simulation method to predict the deactivation process of three-way catalytic converters. Three-way catalytic converter's deactivation typically results from thermal and chemical mechanisms. The major factor of thermal deactivation is the sintering of noble metal particles, which is known to depend on the ageing temperature and the oxygen concentration in the exhaust gas. The chemical deactivation is mainly caused by the poisoning, which has two effects on the catalyst deactivation. One effect is the loss of the catalyst activity, which is expressed by reduced frequency factors of reaction rates. Another effect is the suppression of the noble metal sintering. Poison deposits prevent the noble metal particles from moving in the washcoat, assisted by the reduced thermal loading of reaction heats, which is caused by the loss of the catalyst activity. Modeling these deactivation factors, we propose the rate expression of noble metal sintering.

A system to measure transient temperature distribution on the brake disc rotor at high speed braking has been developed and its measuring principle and configuration were discussed in this paper. This system consists of two revolution sensors and two sets of optical fiber array, photoelectric elements, and microprocessor, which fiber array is so arranged that it faces the brake disc rotor. This new system has the following features: (1) Measuring is made using a visible radiation wavelength range for red hot temperatures higher than 550°C.

An all aluminum cylinder block with a Metal Matrix Composite (MMC) cylinder bore was developed which made it possible to re-design the base engine for high performance with a bore-to-bore distance as narrow as 5.5mm. The cylinder block is an open deck type and the MMC preform consists of alumina-silica fibers and mulite particles. A laminar flow die cast process was selected to ensure defect-free MMC bore quality. To insure good lubrication, electrochemical machining was applied to the bore surface. By use of radioisotope(RI) measurements, MMC reinforcement was optimized for wear characteristics. Particular attention was paid to use of fuels with high sulfur levels.

Automobile production technology has been transferred in the order of "automobile assembly technology", "automotive parts manufacturing technology" and "production preparation technology". Transfer of our "automobile assembly technology" has already been nearly 100% completed and, as the manufacture of local parts is promoted and our experiences to undergo model changes are widened, the transfer of "automotive parts manufacturing technology" and "production preparation technology" is making a steady progress. The most critical point that makes the technical transfer difficult is the small automobile markets in developing countries where it is impossible to acquire a sufficient production volume which permits satisfactorily low cost. Various measures to secure a sufficient production volume such as exports and complementation within regions have been taken so far, but any remarkable effect has not been achieved.

In order to further improve the performance of NOx storage-reduction catalysts (NSR catalysts), focus was placed on their high temperature performance deterioration via sulfur poisoning and heat deterioration. The reactions between the basicity or acidity of supports and the storage element, potassium, were analyzed. It was determined that the high temperature performance of NSR catalysts is enhanced by the interaction between potassium and zirconia, which is a basic metal oxide. Also, a new zirconia-titania complex metal oxides was developed to improve high temperature performance and to promote the desorption of sulfur from the supports after aging.

The authors developed a high-reliability low-cost gold-plated connector for automobiles. The connector is covered with three plated layers, nickel, palladium-nickel alloy, and gold. The three-layer plating helps to reduce the required thickness of gold. This paper describes the reasons why palladium-nickel plating was adopted and compares the corrosion resistance, oxidation resistance and wear resistance of three-layer-plated materials with those of conventional gold-plated materials. In addition, the characterisitics of three-layer-plated connectors were compared with those of conventional gold-plated connectors. It was found that the reliability of three-layer-plated connectors was as high as that of conventional gold-plated connectors.

It is widely known that pellet-typed catalysts are deactivated by phosphorus (ZnDTP) that comes from engine oils. In this paper, the poisoning of monolithic three-way catalysts and oxygen sensors by engine oils is studied. First, catalysts and oxygen sensors were poisoned on the engine bench by test oils in which the quantity of phosphorus and ash was varied. Next, performance of the catalysts and sensors alone was examined and the vehicle exhaust emission at FTP mode was measured on a chassis dynamometer. The results indicate that phosphorus in engine oils poisons the monolithic catalyst and the oxygen sensor resulting in deterioration of the vehicle NOx exhaust emission. However, Ca sulfonate and Mg sulfonate detergents act by restraining phosphorus poisoning of the catalyst and the oxygen sensor. Through analysis of the catalyst and sensor surfaces, it is concluded that phosphorus poisons the catalyst and sensor forming a dense coating.

A camshaft for an automobile engine is generally made of chilled cast iron. But, because of increased demand for higher performance engines, a camshaft with many camshaft has been expected. The cam intervals were necessarily narrow. So it was difficult to manufacture the conventional chilled cast iron camshaft at a moderate price. In the case of a rocker-arm type valve mechanism, higher wear resistance was necessary. After due consideration to solve these problems, development of surface remelted chilled layer camshafts by Toyota's unique manufacturing method has been accomplished. In 1984 Toyota Motor Corporation started the mass-production of this camshaft, first for the new 1.0 liter 1E engine, and then for the 1.3 liter 2E engine. In this paper, the excellent wear resistance, the low manufacturing cost and the characteristic manufacturing method are described.

This paper describes the development of alloy cast iron that can be used for the cutting edges of the trimming die of a press die. Usually, a block of tool steel or steel casting is inserted at the cutting edge of the trimming die of a press die. However, we unified the structure part and the cutting-edge part of a press die with alloy cast iron. As it can''t bear as the cutting edge in this state, the cutting edge is processed by flame-hardening. After the flame- hardening, we developed the alloy cast iron so that enough hardness may be obtained by natural air cooling. Thereby, the machining of the installation seat of the cutting edge decreased and the expense of dies has been reduced.

Model-Based Development (MBD) has become an automotive industry standard process in vehicle control systems development due to the potential to reduce development time and improve engineering quality. This has become even more important as control systems are becoming increasingly complex while development cycle timelines shorten. Toyota utilized Hardware-in-the-Loop Simulations (HILS) techniques when developing the latest Fuel Cell Hybrid Vehicle, FCHV-adv. These MBD techniques contributed to the overall development process, but applications were limited to verifying control specifications. It was recognized that if MBD could be utilized beyond its current role in the control system design process to include functional specification validation, specification quality could be improved while decreasing development time and cost.

This newly developed helical spring can be used at a stress level up to 1300 MPa. The material is composed of Fe-C-Si-Mn-Ni-Cr-Mo-V alloy. Its strength-toughness balance was greatly superior to that of other spring steels. To improve the fatigue strength at a higher stress level, decarburization at the surface upon austenitizing was severely controlled, applying induction heating. Then, a special shot peening process, introduced for the first time, was applied to obtain a surface residual stress at the surface of over 1000 MPa. The spring was first applied to a 1992 TOYOTA model car. Plans are to increase the use since the spring material achieves a weight reduction of at least 30 % and, possibly, 35 to 40 %.

We developed a fastening method to reduce noise levels and fastening work loads. The development was based on research into improved tools and fasteners. This was done in preparation for an increase in elderly worker and female worker population in the Automobile Assembly Shop. The principle of this method is to form female threads inside a straight sleeve by clinching the sleeve around a threaded bolt. We achieved improvements in component material clinching force and a durability for loosening torque compared to conventional bolt and nut methods.

The camshaft for an automobile engine is generally made of chilled cast iron. Due to increasing demand for higher performance, lawer maintenance and better fuel economy, it is difficult to make the cast iron camshaft lighter and/or more durable. In order to overcome these problems, development of an integral camshaft comprised of a sintered alloy cam piece for better wear resistance and steel tube for weight saving has been accomplished. In 1981 Toyota Motor Corporation successively started the mass-production of the sintered intergral camshaft for the new 1.8 liter ls engine. The significant advantages are as follows; (1) Weight saving (2) Excellent wear resistance (3) Improvement of lubrication system (4) Saving machining cost