Search Results

This paper presents a new application of a vehicle on-board battery charger utilizing high frequency Silicon Carbide (SiC) power devices. SiC is one of the most promising alternatives to Silicon (Si) for power semiconductor devices due to its superior material characteristics such as lower on-state resistance, higher junction temperature, and higher switching frequency. An on-board charger prototype is developed demonstrating these advantages and a peak system efficiency of 95% is measured while operating with a switching frequency of 250 kHz. A maximum output power of 6.06 kW results in a gravimetric power density of 3.8 W/kg and a volumetric power density of 5.0 kW/L, which are about 10 times the densities compared with the current Prius Plug-In Si charger. SiC technology is indispensable to eco-friendly PHV/EV development.

Trivalent chromate coating is replacing the conventional hexavalent chromate coating applied on zinc plating. Zinc plating uses one of three types of plating baths (zincate, cyanide and chloride) according to the characteristics required of subject parts. It has been recognized that trivalent chromate coating provides different corrosion resistance depending on the type of zinc plating bath used. Zinc plating with chromate coating were analyzed to clarify the cause of the corrosion resistance variation with the type of zinc plating bath. It has been revealed that the chromate coating thickness and the condition of top SiO2 layer vary with the type of zinc plating bath, resulting in corrosion resistance variation.

In recent years, the automotive manufacturers have been working to reduce fuel consumption in order to cut down on CO2 emissions, promoting weight reduction as one of the fuel saving countermeasures. On the other hand, this trend of weight reduction is well known to reduce vehicle stability in response to disturbances. Thus, automotive aerodynamic development is required not only to reduce aerodynamic drag, which contributes directly to lower fuel consumption, but also to develop technology for controlling unstable vehicle behavior caused by natural wind. In order to control the unstable vehicle motion changed by external contour modification, it is necessary to understand unsteady aerodynamic forces that fluctuating natural wind in real-world environments exerts on vehicles. In the past, some studies have reported the characteristics of unsteady aerodynamic forces induced by natural winds, comparing to steady aerodynamic forces obtained from conventional wind tunnel tests.

Replacing the metal car roof with conventional solar modules results in the increase of total car weight and change of center of mass, which is not preferable for car designing. Therefore, weight reduction is required for solar modules to be equipped on vehicles. Exchanging glass to plastic for the cover plate of solar module is one of the major approaches to reduce weight; however, load bearing property, impact resistance, thermal deformation, and weatherability become new challenges. In this paper a new solar module structure that weighs as light as conventional steel car roofs, resolving these challenges is proposed.

As part of efforts to address climate change and improve energy security, researchers have improved the thermal efficiency of engines by expanding the lean combustion limit. To further expand the lean combustion limit, the authors focused not only on engine technology but the chemical reactivity of various fuel molecules. Furan and anisole were among the fuel molecules selected, based on the idea that promising candidates should enhance the flame propagation speed and have good knocking resistance. Engine testing showed that the lean limit can be expanded by using fuels with the right molecular structures, resulting in higher thermal efficiency.

An experimental study on reducing aerodynamic drag and improving fuel economy through vehicle platooning was conducted to develop an Intelligent Transport System (ITS) with good fuel economy of the entire vehicle-based transportation society. The objectives of the present study are to achieve a simple and quick approach to estimating the aerodynamic drag reduction rates of vehicle platooning. This paper reports the prediction formula, including the conditions of various types of vehicles in multiple-vehicle platooning, based on the power law of a free turbulent axisymmetric wake and on-road experimental results. Note, the prediction formula in this study does not fully include the effect of various type of wake deficit patterns due to rear shape of vehicle and atmospheric wind. Therefore, continuous study is needed to examine the applicable limit.

Two types of new conceptual lead free overlays are developed for automotive internal combustion(IC) engine bearings. The overlays are consisted of molybdenum disulfide(MoS2) and polyamideimide(PAI) resin for binding. One of the overlays is suitable for diesel engines with higher unit load and the other overlay is suitable for gasoline engines with higher sliding velocity. Both overlays indicate good corrosion resistance and wear resistance comparing with conventional lead base overlay. Moreover, higher fatigue resistance is obtained in combination with high performance lead free bearing alloy. These new bearings have the potential to become alternative materials to conventional copper lead bearings with lead base overlay.

Toyota Motor Corporation has been developing technologies for reductions on the environmental load. This paper reports the following as a part of technological development for the painting process. Prior to the application of the E-coat, vehicle bodies are pretreated with zinc phosphates. This is applied to ensure good adhesion and corrosion resistance of the E-coat film. To obtain an excellent pretreatment film, surface conditioning with titanium colloid is generally applied before pretreatment. Since colloid flocculation control was difficult in the case of a conventional titanium colloid-type surface conditioner, the surface conditioner had to be renewed at approximately two-month intervals. The liquid life, however, increased remarkably as a result of adopting fine zinc-type surface conditioners and adding an organic protective surface layer. The water supply/discharge amount was decreased significantly compared with previous amounts.

It is important to reduce aerodynamic drag for reducing fuel consumption. Conventionally reduction of aerodynamic drag has been carried out by shape optimization of each part of a vehicle based on the investigations of the time-averaged flows around the vehicle. However, the general tendency of drag reduction has been saturated recently and it is required to develop a new flow-control technique to achieve further reduction in aerodynamic drag. We therefore focus on the unsteadiness of the flow around a vehicle to achieve it because the aerodynamic drag of a vehicle fluctuates over time due to repetitions of generation, growth, merging and disappearance of various sizes of vortices around it. These vortices are formed by flow separations, for which the longitudinal coherent vortices inside turbulent boundary layers on vehicle surfaces are presumably playing an important role.

This study characterizes the response of the human cadaver abdomen to high-speed seatbelt loading using pyrotechnic pretensioners. A test apparatus was developed to deliver symmetric loading to the abdomen using a seatbelt equipped with two low-mass load cells. Eight subjects were tested under worst-case scenario, out-of-position (OOP) conditions. A seatbelt was placed at the level of mid-umbilicus and drawn back along the sides of the specimens, which were seated upright using a fixed-back configuration. Penetration was measured by a laser, which tracked the anterior aspect of the abdomen, and by high-speed video. Additionally, aortic pressure was monitored. Three different pretensioner designs were used, referred to as system A, system B and system C. The B and C systems employed single pretensioners. The A system consisted of two B system pretensioners. The vascular systems of the subjects were perfused.

Temperature stratification plays an important role in HCCI combustion. The onsets of auto-ignition and combustion duration are sensitive to the temperature field in the engine cylinder. Numerical simulations of HCCI engine combustion are affected by the use of wall boundary conditions, especially the temperature condition at the cylinder and piston walls. This paper reports on numerical studies and experiments of the temperature field in an optical experimental engine in motored run conditions aiming at improved understanding of the evolution of temperature stratification in the cylinder. The simulations were based on Large-Eddy-Simulation approach which resolves the unsteady energetic large eddy and large scale swirl and tumble structures. Two dimensional temperature experiments were carried out using laser induced phosphorescence with thermographic phosphors seeded to the gas in the cylinder.

This paper describes the development of a fatigue life prediction method for Laser Screw Welding (LSW). Fatigue life prediction is used to assess the durability of automotive structures in the early design stages in order to shorten the vehicle development time. The LSW technology is a spot-type joining method similar to resistance spot welding (RSW), and has been developed and applied to body-inwhite structures in recent years. LSW can join metal panels even when a clearance exists between the panels. However, as a result of this favorable clearance-allowance feature of LSW, a concave shape may occur at the nugget part of the joint. These LSW geometric features, the concavity of nuggets and the clearance between panels, are thought to affect the local stiffness behavior of the joint. Therefore, while assessing the fatigue life of LSW, it is essential to estimate the influence of these factors adequately for the representation of the local stiffness behavior of the joint.

The research described in this paper aimed to study the cornering resistance and dissipation power on the tire contact patch, and to develop an efficient direct yaw moment control (DYC) during acceleration and deceleration while turning. A previously reported method [1], which formulates the cornering resistance in steady-state cornering, was extended to so-called quasi steady-state cornering that includes acceleration and deceleration while turning. Simulations revealed that the direct yaw moment reduces the dissipation power due to the load shift between the front and rear wheels. In addition, the optimum direct yaw moment cancels out the understeer augmented by acceleration. In contrast, anti-direct yaw moment optimizes the dissipation power during decelerating to maximize kinetic energy recovery. The optimization method proved that the optimum direct yaw moment can be achieved by equalizing the slip vectors of all the wheels.

Electric vehicles (EVs) are attracting attention due to growing awareness of environmental issues such as fossil fuel depletion and global warming. In particular, a wide range of research has examined how direct yaw moment controls (DYCs) can enhance the handling performance of EVs equipped with multiple in-wheel motors (IWMs) or the like. Recently, this research has focused on reducing energy consumption through driving force distribution control. The first report proposed a method to minimize energy consumption through an efficient DYC for extending the cruising range of a vehicle installed with four IWMs, and described the vehicle behavior with this control. Since motors allow high design flexibility, EVs can be developed with a variety of drive systems. For this reason, various driving force distribution control methods can be considered based on the adopted system.

Low frequency interior wind noise is typically dominated by underfloor flow noise. The source mechanisms are fluctuating surface pressure loading from both flow turbulence and acoustic field levels developed in the semi-reverberant cavity between floor and road. Previous studies have used computation fluid dynamics (CFD) to estimate the aero-acoustic loading applied to a vibro-acoustic model, which is then used to predict the transmitted interior wind noise. This paper reports a new perspective in two respects. First it uses novel surface pressure microphone arrays to directly measure the underfloor aero-acoustic loading in the wind tunnel. Second, it considers two different underfloor aerodynamic configurations - with and without lightweight aero cover panels, which are installed primarily to reduce aerodynamic drag.

A vehicle parking manoeuvre is characterized by low or zero speed, small turning radius and large yaw velocity of the steered wheels. To predict the forces and moments generated by a wheel under these conditions, the Pacejka Magic Formula model has been extended to incorporate the effect of spin (turn slip model) in the past years. The extensions have been further developed and incorporated in the MFTyre/MF-Swift 6.2 model. This paper describes the development of a method for the identification of the turn slip parameters. Based on the operating conditions of a typical parking manoeuvre, the dominant parameters of the turn slip model are firstly defined. At an indoor test facility, the response of a tyre under the identified operating conditions is measured. An algorithm is developed to identify the dominant turn slip parameters from the measured responses.

A highly anti-corrosive organic-inorganic hybrid paint for automotive steel parts has been developed. The inorganic component included in the paint is silicon dioxide (SiO2), which has the capability to passivate zinc. By application of the paint on a trivalent chromatetreated zinc-plated steel sheet or a trivalent chromate-treated zinc-nickel-plated steel sheet, high anti-corrosion protection can be provided to steel materials. Particularly in the case of application over a zinc-nickel-plated steel sheet, 0 mm corrosion depth after a cyclic corrosion test (CCT) of 450 cycles was demonstrated.

In order to reduce the energy consumption of the automotive air conditioning system, adsorption heat pump (AHP) system is one of the key technologies. We have been developing compact AHP system utilizing the exhaust heat from the engine coolant system (80-100 °C), which can meet the requirements in the automotive application. However, AHP systems have not been practically used in automotive applications because of its low volumetric power density of the adsorber. The volumetric power density of the adsorber is proportional to sorption rate, packing density and latent heat. In general, the sorption rate is determined by mass transfer resistance in primary particle of an adsorbent and heat and mass transfer resistance in packed bed. In order to improve the volumetric power density of the adsorber, it is necessary to increase the production of the sorption rate and the packing density.

The Cathode Ray Tube (CRT) has many superior characteristics compared to other display devices in the area of response, high-resolution, full-color and multi-display capabilities. However, CRTs commonly- used in offices or in the home have not been applicable for automobiles because they could not ensure sufficient display. performance, brightness, vibration resistance, and reliability due to the severe driving conditions of the automobile. We examined the applicability of the CRT into an automobile display system using an experimental vehicle and improved six especially important aspects such as dimensions, display appearance time, effect of magnetism, visibility, stabilization of brightness and prevention of excessive battery drain. Consequently, we developed a new display system called “Toyota Electro Multivision” and introduced it into the ‘85 Toyota Soarer, a luxury class passenger car for the Japanese market only.

In fatal accidents due to heavy duty trucks, the fatalities of occupants in passenger cars in which rear-end collision occur account for the largest percent. Collisions to the vehicles in traffic jams and collision to other accidents scenes on express ways can result in serious repercussions. Therefore the system which reduces the damage of collisions has long been demanded and here the world-first Pre-crash Safety (PCS) System for heavy duty trucks was developed. This system gives warning to the driver in case there is a possibility of collision with preceding vehicles, and activates the brakes to mitigate damage in case there is a higher possibility of collision. In order to get the maximum effect on the express ways where the trucks are in high speed, it is necessary to give warning and activate the brakes with relatively early timing.