Search Results

The SAE G-27 committee was tasked by ICAO to develop a performance-based packaging standard for lithium batteries transported as cargo on aircraft. The standard details test criteria to qualify packages of lithium batteries & cells for transportation as cargo on-board passenger aircraft. Lithium batteries and cells have been prohibited from shipment as cargo on passenger aircraft since 2016. This paper summarizes the results of the tests conducted by Transport Canada and National Research Council Canada to support the development of this standard with evidence-based recommendations. It includes a description of the test specimens, the test set up, instrumentation used, and test procedures following the standard as drafted to date. The study considered several lithium-ion battery and cell chemistries that were tested under various proposed testing scenarios in the draft standard.

This paper provides details on the tests performed and the research findings of an underride guard test programme, including 10 full scale crashes using three types of deformable guards. The deformable guards tested included one meeting the minimum requirements of the NHTSA FMVSS 223 with ground clearances of either 560 or 480 mm, a second meeting the same minimum performance criteria with the addition of a device to limit the displacement of the horizontal member (ground clearance of 480 mm only) and a third being stiffer and designed to roughly maintain its 560 mm ground clearance during deformation. Crash tests were performed at speeds of 48, 56 and 65 kph.

The belt-fit test device (BTD) measures and assesses static seat belt geometry of automobile seat belts. It was conceived and developed by Transport Canada throughout the 1970s, 1980s and 1990s to address abdominal and upper body injuries that resulted from a mismatch between seat belt geometry and occupants' anthropometric characteristics. When positioned on an automobile seat, the BTD indicates whether the lap and shoulder belts fall within specified bounds that have been established to minimize the risk of serious injuries to soft tissue and organs from belt intrusion. Recently, work has focused on the development of an electronic version of the BTD using computer-human modeling techniques and computer-aided design (CAD). Tecmath AG, creators of the RAMSIS™ 3D human modeling system, are currently developing an electronic BTD (or eBTD).

Correctly fitted seat belts save the lives of car passengers everyday. In attempt to reduce the risk of injuries, primarily abdominal, caused by inappropriate belt fitting, Transport Canada developed the Belt fit Test Device (BTD). The BTD is a physical hardware measuring device that tests whether the lap and torso belt are appropriately positioned with respect to the bony structures of the pelvis and rib cage of the restrained occupant. To overcome the deviations of hardware physical tests and to enable review of belt design in early design phases, the Alliance of Automobile Manufacturers funded the development of an electronic simulation and modeling tool in the form of an electronic Belt fit Test Device (eBTD). The development takes place in close co-operation with the Joint Working Group on Abdominal Injury Reduction (JWG-AIR).

Automatic emergency braking and forward collision warning (FCW) reduce the incidence of police-reported rear-end crashes by 27% to 50%, but these systems may not be effective for preventing rear-end crashes with nonpassenger vehicles. IIHS and Transport Canada evaluated FCW performance with 12 nonpassenger and 7 passenger vehicle or surrogate vehicle targets in five 2021-2022 model year vehicles. The presence and timing of an FCW was measured as a test vehicle traveling 50, 60, or 70 km/h approached a stationary target ahead in the lane center. Equivalence testing was used to evaluate whether the proportion of trials with an FCW (within ± 0.20) and the average time-to-collision of the warning (within ± 0.23 sec) for each target was meaningfully different from a global vehicle car target (GVT).

This paper reports the results of a study to determine the effects of a top tether strap on the performance of child restraint systems (CRS). Four commercially available CRSs and the CanFIX were tested. All restraints tested had a similar design T-shield type harness system to minimize harness variability. As part of the test matrix, tether webbing, tether height and tether slack were varied. The dummies used for testing were the 12-and 18-month CRABI. Head and chest acceleration, head excursion, upper and lower neck loads and resultant moments were recorded. Although the presence of slack in the tether strap degrades the performance of the CRS, a tether strap with slack present improved the response of a dummy restrained in a CRS when compared to an identical tetherless restraint. With maximum slack, the results for the restraint condition approached results from a tetherless condition while still demonstrating a slight benefit.

Two manufacturers, Denton ATD and FTSS, currently produce the Hybrid III 5th percentile female dummy. In response to concerns raised by industry that differences in the anthropometry of the molded breasts between the two manufacturers may influence chest responses, Transport Canada conducted a comparative testing program. Thorax biofidelity tests were conducted to compare force-deflection characteristics; full-frontal, rigid-barrier tests were conducted at 40, 48 and 56 km/h to compare chest responses, and out-of-position chest on module static airbag deployment tests were conducted to compare peak chest deflections of the Denton and FTSS dummy jackets and of a prototype jacket without breasts. Differences in force-deflection characteristics were observed during biofidelity pendulum impacts of the two dummies, with much of the differences attributed to the different chest jackets.

Tailpipe emissions, fuel consumption, and wheel torque data were measured for three pairs of vehicles tested over four drive cycles at the Emissions Research and Measurement Section of Environment and Climate Change Canada in Ottawa, Ontario. Each pair of vehicles included identical vehicle models; one vehicle was equipped with an AWD drivetrain and one vehicle was equipped with a FWD drivetrain. The AWD vehicle was tested on a double-axle chassis dynamometer. The amount of AWD activity was heavily dependent on driving behavior and AWD system design. During periods of torque delivery, the percentage of AWD activity ranged between 32% and 57% for the FTP-75 drive cycle, between 3% and 8% for the HWFCT drive cycle, and between 21% and 29% for the US06 drive cycle. The fourth drive cycle was the FTP-75 driven at -7°C. AWD distributions did not show sensitivity to temperature for the first and second vehicle models.

The responses of a 5th percentile female ATD in the driver and/or rear passenger positions of 56 crashes are described. The Transport Canada side impact programme consisted of LTV-to-car impacts, car-to-car impacts and IIHS barrier-to-car tests. The majority of the tests involved severe crash conditions for which the vehicles were not designed. The SID-IIs head, chest and abdominal responses were compared to determine the effects of the striking bullet geometry, the angle of impact, the impact point and the self-protective elements of the struck vehicle, including airbag technology and armrest designs. The SID-IIs head responses and deflection measures were sufficiently sensitive to discriminate between the various striking vehicles, crash configurations, airbag systems and armrest characteristics.

Drawing on provincial data files maintained by Transport Canada, the injury experience of passenger vehicle occupants as a function of occupant seating position, reported restraint use and occupant age is examined. Particular attention is given to the issue of rear seat lap belt effectiveness. Estimates of restraint system effectiveness are derived using a variety of approaches. These range from direct comparisons of the relative injury/fatality rates of restrained and unrestrained occupants in reportable accidents to double-pair comparisons based on “subject” and “control” occupants in fatal accidents. Available Canadian data suggest that the use of three-point seat belts by front seated occupants and the use of lap belts by rear seated occupants substantially reduces the likelihood of serious or fatal injury.

Passenger car side impact crash tests and sled tests were conducted to investigate the influence of booster seats, near-side occupant characteristics and vehicle interiors on the responses of the Q6/Q6s child ATD positioned in the rear, far-side seating location. Data from nine side impact sled tests simulating a EuroNCAP AEMD barrier test were analyzed with data obtained from 44 side impact crash tests. The crash tests included: FMVSS 214 and IIHS MDB, moving car-to-stationary car and moving car-to-moving car. A Q6 or prototype Q6s ATD was seated on the far-side, using a variety of low and high back booster seats. Head and chest responses were recorded and ATD motions were tracked with high-speed videos. The vehicle lateral accelerations resulting from MDB tests were characterized by a much earlier and more rapid rise to peak than in tests where the bullet was another car.

Current Canadian and United States fuel consumption test procedures and labeling calculations can underestimate the potential real-world benefits of advanced technologies such as stop-start systems. The fuel consumption results outlined in this paper support that point, since the 2-cycle (UDDS, HWFET) test results under-represent the fuel savings when compared to the urban-centered New York City (NYCC) driving cycle and the Japanese 10-15 (J10-15) mode driving cycle when the stop-start system is activated. Vehicles equipped with stop-start systems can use less fuel in urban driving than is apparent from the current published fuel consumption values. The evaluation of off-cycle and real-world testing aims to demonstrate the potential savings of stop-start technology.

Terrestrial winds play an important role in affecting the aerodynamics of road vehicles. Of increasing importance is the effect of the unsteady turbulence structure of these winds and their influence on the process of optimizing aerodynamic performance to reduce fuel consumption. In an effort to predict better the aerodynamic performance of heavy-duty vehicles and various drag reduction technologies, a study was undertaken to measure the turbulent wind characteristics experienced by heavy-duty vehicles on the road. To measure the winds experienced on the road, a sport utility vehicle (SUV) was outfitted with an array of four fast-response pressure probes that could be arranged in vertical or horizontal rake configurations that provided measurements up to 4.0 m from the ground and spanning a width of 2.4 m. To characterize the influence of the proximity of the vehicle on the pressure signals of the probes, the SUV and its measurements system was calibrated in a large wind tunnel.

A study of vehicle accident data from insurance claim files was conducted to determine the relative effectiveness of red and amber turn-signal systems in reducing rear-end collisions. The effectiveness was measured in terms of the relative frequency of accidents involving these systems, with respect to a number of vehicle, environmental, and driver factors. Control for vehicle exposure was made by comparing the non-turning accidents with the turning accidents for the relevant rear-turn-signal systems. Analyses revealed that there were no statistically significant differences in rear-end accident rates between the red and amber turn-signal systems. On the basis of safety benefits, the results of the study did not appear to provide sufficient justification for changes to the present Motor Vehicle Safety Standards regarding the functional separation and colour coding of a rear-turn-signal system.

In 1998, Rouhana et al. described development of a new device, called the IR-TRACC (InfraRed - Telescoping Rod for Assessment of Chest Compression). In its original concept, the IR-TRACC uses two infrared LEDs inside of a telescoping rod to measure deflection. One LED serves as a light transmitter and the other as a light receiver. The output from the receiver LED is converted to a linear function of chest compression using an analog circuit. Tests have been performed with IR-TRACC units at various labs around the world since 1998. A first-generation IR-TRACC system was retrofit into a Q3 dummy by TNO. Similarly, a mid sized male Hybrid III dummy thorax and a small female Hybrid III dummy thorax have been designed by First Technology Safety Systems (FTSS) such that each contains 4 second-generation IR-TRACC units. The second-generation IR-TRACC is the result of continued development by FTSS, especially in the areas of the analysis circuit, manufacturing and calibration methods.

Dummy response and restraint configuration factors associated with a known child injury environment were investigated using a spinal-cord injury accident case, a full-scale reconstruction, and sled simulations. The work is one of several studies undertaken in association with the International Task Force on Child Restraining Systems to support the development of improved neck injury criteria and restraint systems for young children. A two-vehicle crash involving a restrained child occupant was investigated in detail and reconstructed in full-scale at the Transport Canada Motor Vehicle Test Centre using the CRABI 6-Month dummy. Vehicle damage and crush characteristics closely resembled that of the case vehicles. Dummy instrumentation included head and chest accelerometers and upper and lower neck transducers. The case occupant had been facing forward and had sustained a contusion of the spinal cord at T2 that resulted in paraplegia.

This technical paper presents the results from tests conducted with the ES-2re, a version of the ES-2 side impact dummy that was modified by the National Highway Traffic Safety Administration (NHTSA) to improve its performance in crash tests. Through the series of biofidelity tests conducted on the ES-2re, described in International Standards Organization (ISO) Technical Report (TR)9790 (1999), the OSRP observed a final overall biofidelity ranking of 4.1 for the ES-2re, which corresponds to an ISO classification of “marginal.” The biofidelity of the ES-2re is compared to that of the ES-2 and the WorldSID. Repeatability was also evaluated on the ES-2re based on the biofidelity test data. Additional pendulum tests were performed to assess the response of the dummy in oblique loading conditions, and results indicate that oblique loading from the front leads to significantly reduced rib deflections.

In a campaign to quantify the aerodynamic drag changes associated with drag reduction technologies recently introduced for light-duty vehicles, a 3-year, 24-vehicle study was commissioned by Transport Canada. The intent was to evaluate the level of drag reduction associated with each technology as a function of vehicle size class. Drag reduction technologies were evaluated through direct measurements of their aerodynamic performance on full-scale vehicles in the National Research Council Canada (NRC) 9 m Wind Tunnel, which is equipped with a the Ground Effect Simulation System (GESS) composed of a moving belt, wheel rollers and a boundary layer suction system. A total of 24 vehicles equipped with drag reduction technologies were evaluated over three wind tunnel entries, beginning in early 2014 to summer 2015. Testing included 12 sedans, 8 sport utility vehicles, 2 minivans and 2 pick-up trucks.

New technology is enabling tire manufacturers to reduce tire rolling resistance, leading to reduced fuel consumption and greenhouse gas emissions in the transportation sector. This project analyzed current relationships between the environmental and safety performance of commercially-available light-duty tire models in North America. Performance data was rated using the EC No. 1222/2009, and compared against tire price, uniform tire quality grading standards (UTQG), and other attributes. A random selection of tire models was tested, consisting of: 108 all-season, 23 studless winter, and 5 all-weather tire models. All test results were blinded for the purpose of confidentiality. Tire rolling resistance coefficients were measured using the single point ISO 28580 standard, and wet grip index values were measured according to UN-ECE Reg.117. Rolling resistance and wet grip indicators were measured using dynamic mechanical analysis (DMA).

In the fall of 2000, the Council of Ministers agreed that Canada should retain the vision of having the safest roads in the world, and that a longer term successor plan, called Road Safety Vision 2010, carry forward the work of Canada's inaugural national road safety plan. It was further agreed that the plan include an overall national target and sub-targets. A national target that calls for 30% decreases in the average number of road users killed and seriously injured during the 2008-2010 period below comparable 1996-2001 figures is currently under consideration. Achievement of this target would reduce Canada's road fatality total to fewer than 2100 by 2010.