Search Results

The gas velocity through an automotive catalyst has been determined by measuring the time of flight of a pulse of propane injected at the inlet plane of the catalyst. The arrival time at the exit plane was detected by a fast flame ionization detector. By synchronizing and delaying the injection of propane with respect to the engine crankshaft position, the fluctuations of the exhaust gas velocity during the engine cycle were investigated. A number of tests at different engine load and speed points were carried out. The results show a complex velocity/time characteristic, including flow reversals. The technique is shown to be a viable option for flow measurement in this harsh environment.

This paper describes cyclic Air/Fuel ratio (AFR) measurements carried out with a novel device (fUEGO) based on a production Universal Exhaust Gas Oxygen sensor, but modified to give an improved frequency response. The results are compared to AFR calculated from a fast CO/CO2 analyser and a fast response flame ionization detector (FID). The direct comparison of the two different methods for determining the cyclic AFR reveals that the electrochemical device is in reasonable agreement with the more complex carbon balance method and can provide reliable cyclic AFR measurements with a reduced requirement for equipment and data post processing. The fUEGO however is sensitive to elevated levels of uHC's (unburned hydrocarbons) during misfires or partial burns and readings during such situations usually show deviations compared to the carbon balance method.

This paper presents two new methods to quantitatively evaluate the mechanical durability of multi-layered automotive paint systems. The first examines the resistance of the paint system to particle impacts and involves the impact of hard particles against the painted surface, under controlled conditions. The second test examines the resistance of the clearcoat layer in the paint system to surface abrasion, or mar. The test uses a steel sphere which is rotated against the paint surface in the presence of a slurry of fine abrasive particles. These two techniques have been successfully applied to a set of commercial automobile paints, and were found to discriminate well between them and give reproducible, quantitative data. The effects of the bake conditions on both the erosion and abrasion resistance of a full paint system and the abrasion resistance of a range of commercial clearcoats are examined in detail.

A multi-objective optimization scheme based on stochastic global search is developed and used to examine the performance of an HCCI model containing a reduced chemical kinetic mechanism, and to study interrelations among different model responses. A stochastic reactor model of an HCCI engine is used in this study, and dedicated HCCI engine experiments are performed to provide reference for the optimization. The results revealed conflicting trends among objectives normally used in mechanism optimization, such as ignition delay and engine cylinder pressure history, indicating that a single best combination of optimization variables for these objectives did not exist. This implies that optimizing chemical mechanisms to maintain universal predictivity across such conflicting responses will only yield a predictivity tradeoff. It also implies that careful selection of optimization objectives increases the likelihood of better predictivity for these objectives.

One of the limits on the maximum fuel efficiency benefit to be gained from turbocharged, downsized gasoline engines is the occurrence of low speed pre-ignition (LSPI). LSPI may lead to high pressures and extreme knock (megaknock or superknock) which can cause severe engine damage. Though the mechanism leading to megaknock is not completely resolved, LSPI is thought to arise from local auto-ignition of areas in the cylinder which are rich in low ignition delay “contaminants” such as engine oil and/or heavy ends of gasoline. These contaminants are introduced to the combustion chamber at various points in the engine cycle (e.g. entering from the top land crevice during blow-down or washed from the cylinder walls during DI wall impingement). This paper describes a method for testing the propensity of different contaminants to cause a local pre-ignition in a gasoline engine. During one cycle, a small amount of contaminant is injected into one cylinder of a 4 cylinder engine.

One of the limits on the maximum fuel efficiency benefit to be gained from turbocharged, downsized gasoline engines is the occurrence of pre-ignitions at low engine speed. These pre-ignitions may lead to high pressures and extreme knock (megaknock or superknock) which can cause severe engine damage. Though the mechanism leading to megaknock is not completely resolved, pre-ignitions are thought to arise from local autoignition of areas in the cylinder which are rich in low ignition delay “contaminants” such as engine oil and/or heavy ends of gasoline. These contaminants are introduced to the combustion chamber at various points in the engine cycle (e.g. entering from the top land crevice during blow-down or washed from the cylinder walls during DI wall impingement).

A novel modeling approach is applied to investigate the use of hydrogen-rich gas (HRG) for controlling the combustion process in a Homogenous-Charge Compression-Ignition (HCCI) engine. A detailed-chemistry stochastic reactor model is coupled with a one-dimensional gas dynamics model to account for the full engine cycle. The integrated model simulates the steady-state and transient operation of a single-cylinder HCCI engine. A previously developed tabulation scheme is utilized to speed up the detailed-chemistry simulations, which, though computationally cheap compared to many other approaches, are impractical for simulations involving a large number of cycles. A control strategy based on HRG addition is implemented using a closed-loop controller built within the gas dynamics model. Simulations conducted at different speeds and with varying loads indicate that the HRG can be effectively used to control the combustion phasing, and hence expand the operating range of the HCCI engine.

A dual-fuel approach to control combustion in HCCI engine is investigated in this work. This approach involves controlling the combustion heat release rate by adjusting fuel reactivity according to the conditions inside the cylinder. Experiments were performed on a single-cylinder research engine fueled with different ratios of primary reference fuels and operated at different speed and load conditions, and results from these experiments showed a clear potential for the approach to expand the HCCI engine operation window. Such potential is further demonstrated dynamically using an optimized stochastic reactor model integrated within a MATLAB code that simulates HCCI multi-cycle operation and closed-loop control of fuel ratio. The model, which utilizes a reduced PRF mechanism, was optimized using a multi-objective genetic algorithm and then compared to a wide range of engine data.

The objective of this study was to examine the operating characteristics of a light duty multi cylinder compression ignition engine with regular gasoline fuel at low engine speed and load. The effects of fuel stratification by means of multiple injections as well as the sensitivity of auto-ignition and burn rate to intake pressure and temperature are presented. The measurements used in this study included gaseous emissions, filter smoke opacity and in-cylinder indicated information. It was found that stable, low emission operation was possible with raised intake manifold pressure and temperature, and that fuel stratification can lead to an increase in stability and a reduced reliance on increased temperature and pressure. It was also found that the auto-ignition delay sensitivity of gasoline to intake temperature and pressure was low within the operating window considered in this study.

Large-bore natural gas engines may use pre-chamber ignition. Despite extensive research in engine environments, the exact nature of the jet, as it exits the pre-chamber orifice, is not thoroughly understood and this leads to uncertainty in the design of such systems. In this work, a specially-designed rig comprising a quartz pre-chamber fit with an orifice and a turbulent flowing mixture outside the pre-chamber was used to study the pre-chamber flame, the jet, and the subsequent premixed flame initiation mechanism by OH* and CH* chemiluminescence. Ethylene and methane were used. The experimental results are supplemented by LES and 0D modelling, providing insights into the mass flow rate evolution at the orifice and into the nature of the fluid there. Both LES and experiment suggest that for large orifice diameters, the flow that exits the orifice is composed of a column of hot products surrounded by an annulus of unburnt pre-chamber fluid.

A standard port fuel injected, unthrottled single cylinder four-stroke SI engine, with a compression ratio of 10.3:1, and using standard gasoline fuel, has been adapted to operate in the homogeneous charge compression ignition (HCCI) mode, by modifying the valve timing. It has been found that over a speed range of between 1300 and 2000 rpm, and lambda values of between 0.95 and 1.1, stable operation is achieved without spark ignition. The internal EGR rate was estimated to be about 60%, and emissions of NOX were typically 0.25 g/kWh. Practical implementation of this HCCI concept will require variable valve timing, which will also enable reversion to standard SI operation for maximum power.

Gasoline Homogeneous Charge Compression Ignition (HCCI) combustion has been studied widely in the past decade. However, in HCCI engines using negative valve overlap (NVO), there is still uncertainty as to whether the effect of pilot injection during NVO on the start of combustion is primarily due to heat release of the pilot fuel during NVO or whether it is due to pilot fuel reformation. This paper presents data taken on a 4-cylinder gasoline direct injection, spark ignition/HCCI engine with a dual cam system, capable of recompressing residual gas. Engine in-cylinder samples are extracted at various points during the engine cycle through a high-speed sampling system and directly analysed with a gas chromatograph and flame ionisation detector. Engine parameter sweeps are performed for different pilot injection timings and quantities at a medium load point.

The information provided by the in-cylinder pressure signal is of great importance for modern engine management systems. The obtained information is implemented to improve the control and diagnostics of the combustion process in order to meet the stringent emission regulations and to improve vehicle reliability and drivability. The work presented in this paper covers the experimental study and proposes a comprehensive and practical solution for the estimation of the in-cylinder pressure from the crankshaft speed fluctuation. Also, the paper emphasizes the feasibility and practicality aspects of the estimation techniques, for the real-time online application. In this study an engine dynamics model based estimation method is proposed. A discrete-time transformed form of a rigid-body crankshaft dynamics model is constructed based on the kinetic energy theorem, as the basis expression for total torque estimation.

A turbulent combustion model is described for SI engines with large variations in mixture strength. The model is for a single gas phase fluid at high Reynolds number and treats combustion in the laminar flamelet regime, which is characterized by high Damkholer and low Karlovitz numbers. An assumed probability density function (pdf) approach is used to extract expressions for mean quantities of interest, which are parameterized on the progress variable and mixture fraction variables. A double delta function pdf is used for the reaction progress variable and a beta function pdf is used for the mixture fraction. The reaction rate term in the progress variable equation is closed using an algebraic expression, which incorporates the effects of mixture strength, pressure and temperature on laminar flame speed. The model is implemented in two versions of a Computational Fluid Dynamics (CFD) code.

Simple air-path models for modern (VGT/EGR equipped) diesel engines are in common use, and have been reported in the literature. This paper addresses some of the shortcomings of control-oriented models to allow better prediction of the cylinder charge properties. A fast response CO2 analyzer is used to validate the model by comparing the recorded and predicted CO2 concentrations in both the intake port and exhaust manifold of one of the cylinders. Data showing the recorded NOx emissions and exhaust gas opacity during a step change in engine load illustrate the spikes in both NOx and smoke seen during transient conditions. The predicted cylinder charge properties from the model are examined and compared with the measured NOx and opacity. Together, the emissions data and charge properties paint a consistent picture of the phenomena occurring during the transient. Alternative strategies for the fueling and cylinder charge during these load transients are investigated and discussed.

The European Emissions Stage 5b standard for diesel passenger cars regulates particulate matter to 0.0045 g/km and non-volatile part/km greater than 23 nm size to 6.0x10₁₁ as determined by the PMP procedure that uses a heated evaporation tube to remove semi-volatile material. Measurement artifacts associated with the evaporation tube technique prevents reliable extension of the method to a lower size range. Catalytic stripper (CS) technology removes possible sources of these artifacts by effectively removing all hydrocarbons and sulfuric acid in the gas phase in order to avoid any chemical reactions or re-nucleation that may cause measurement complications. The performance of a miniature CS was evaluated and experimental results showed solid particle penetration was 50% at 10.5 nm. The sulfate storage capacity integrated into the CS enabled it to chemically remove sulfuric acid vapor rather than rely on dilution to prevent nucleation.

The cylinder pressure signal, as an instantaneous and direct measure of the engine operation, contains valuable information for closed loop engine control and offers very useful engine monitoring and control capabilities. The estimation technique for cylinder pressure has been investigated for many years. Based on the Frequency Analysis Method, a synthetic estimation method is proposed in this paper to estimate pressure. Methods that are successful in obtaining a more accurate estimated cylinder pressure over a wider range of crankshaft angle are reported. Quantitative results obtained from application of the method are also given.