Search Results

An endoscope-based image acquisition-and-processing camera system was used for diagnostics of pilot injection combustion in a single-cylinder heavy duty diesel engine. A study of the pilot injection or light load is of interest because the spray breakup, mixing and vaporization processes are less influenced by heat feedback from the flame than in full injection cases. This allows the spray process to be decoupled from the combustion process. The experimental cases were modeled using a version of the KIVA-II code that includes improvements in the turbulence, wall heat transfer, spray, ignition and combustion models. Pilot injections of three different amounts (10, 15 and 20% of the fuel injected at 75% load and 1600 RPM) at different start-of-injection timings were studied. The imaging system included an endoscope, an intensified CID camera, a frame grabber and the control circuitry.

The objectives of this study were 1) to evaluate the characteristics of rich diesel combustion near the stoichiometric operating condition, 2) to explore the possibility of stoichiometric operation of a diesel engine in order to allow use of a three-way exhaust after-treatment catalyst, and 3) to achieve practical operation ranges with acceptable fuel economy impacts. Boost pressure, EGR rate, intake air temperature, fuel mass injected, and injection timing variations were investigated to evaluate diesel stoichiometric combustion characteristics in a single-cylinder high-speed direct injection (HSDI) diesel engine. Stoichiometric operation in the Premixed Charge Compression Ignition (PCCI) combustion regime and standard diesel combustion were examined to investigate the characteristics of rich combustion. The results indicate that diesel stoichiometric operation can be achieved with minor fuel economy and soot impact.

The effect of spray targeting on exhaust emissions, especially soot and carbon monoxide (CO) formation, were investigated in a single-cylinder, high-speed, direct-injection (HSDI) diesel engine. The spray targeting was examined by sweeping the start-of-injection (SOI) timing with several nozzles which had different spray angles ranging from 50° to 154°. The tests were organized to monitor the emissions in Premixed Charge Compression Ignition (PCCI) combustion by introducing high levels of EGR (55%) with a relatively low compression ratio (16.0) and an open-crater type piston bowl. The study showed that there were optimum targeting spots on the piston bowl with respect to soot and CO formation, while nitric oxide (NOx) formation was not affected by the targeting. The soot and CO production were minimized when the spray was targeted at the edge of the piston bowl near the squish zone, regardless of the spray angle.

A level set method (G-equation)-based combustion model incorporating detailed chemical kinetics has been developed and implemented in KIVA-3V for Spark-Ignition (SI) engine simulations for better predictions of fuel oxidation and pollutant formation. Detailed fuel oxidation mechanisms coupled with a reduced NOX mechanism are used to describe the chemical processes. The flame front in the spark kernel stage is tracked using the Discrete Particle Ignition Kernel (DPIK) model. In the G-equation model, it is assumed that after the flame front has passed, the mixture within the mean flame brush tends to local equilibrium. The subgrid-scale burnt/unburnt volumes of the flame containing cells are tracked for the primary heat release calculation. A progress variable concept is introduced into the turbulent flame speed correlation to account for the laminar to turbulent evolution of the spark kernel flame.

An emissions and performance study was conducted to explore the effects of exhaust gas recirculation (EGR) and multiple injections on the emission of oxides of nitrogen (NOx), particulate emissions, and brake specific fuel consumption (BSFC) over a wide range of engine operating conditions. The tests were conducted on an instrumented single cylinder version of the Caterpillar 3400 series heavy duty Diesel engine. Data was taken at 1600 rev/min, and 75% load, and also at operating conditions taken from a 6-mode simulation of the federal transient test procedure (FTP). The fuel system used was an electronically controlled, common rail injector and supporting hardware. The fuel system was capable of as many as four independent injections per combustion event at pressures from 20 to 120MPa.

Experiments show that intake flow details have a significant influence on High-Speed Direct-Injection (HSDI) diesel engine soot emissions. Four different intake modes were simulated using the combination of the CFD codes, STAR-CD and KIVA-3V, to investigate spray-intake flow-emission interaction characteristics. The simulation results were compared to steady-state flow bench data and engine experimental data. It was found that it is difficult to accurately predict the timing of the small pilot and main combustion events, simultaneously, with current simplified ignition models. NOx emissions were predicted well, however, an insensitivity of the soot emissions to the details of the intake process was found, mainly due to the deficiencies in predicting the ignition delay. The results show that a strong swirling flow causes the formed soot to remain within the bowl, leading to high soot emissions.

Reactivity Controlled Compression Ignition (RCCI) is an engine combustion strategy that produces low NO and PM emissions with high thermal efficiency. Previous RCCI research has been investigated in single-cylinder heavy-duty engines. The current study investigates RCCI operation in a light-duty multi-cylinder engine at 3 operating points. These operating points were chosen to cover a range of conditions seen in the US EPA light-duty FTP test. The operating points were chosen by the Ad Hoc working group to simulate operation in the FTP test. The fueling strategy for the engine experiments consisted of in-cylinder fuel blending using port fuel-injection (PFI) of gasoline and early-cycle, direct-injection (DI) of diesel fuel. At these 3 points, the stock engine configuration is compared to operation with both the original equipment manufacturer (OEM) and custom-machined pistons designed for RCCI operation.

In this study we identify components of a typical biodiesel fuel and estimate both their individual and mixed thermo-physical and transport properties. We then use the estimated mixture properties in computational simulations to gauge the extent to which combustion is modified when biodiesel is substituted for conventional diesel fuel. Our simulation studies included both conventional diesel combustion (DI) and premixed charge compression ignition (PCCI). Preliminary results indicate that biodiesel ignition is significantly delayed due to slower liquid evaporation, with the effects being more pronounced for DI than PCCI. The lower vapor pressure and higher liquid heat capacity of biodiesel are two key contributors to this slower rate of evaporation. Other physical properties are more similar between the two fuels, and their impacts are not clearly evident in the present study.

Particle Image Velocimetry (PIV) was used to make gas velocity and turbulence measurements in a motored diesel engine. The experiments were conducted using a single-cylinder version of the Caterpillar 3406 production engine. One of the exhaust valves and the fuel injector port were used to provide optical access to the combustion chamber so that modifications to the engine geometry were minimal, and the results are representative of the actual engine. Measurements of gas velocity were made in a plane in the piston bowl using TiO2 seed particles. The light sheet necessary for PIV was formed by passing the beam from a Nd:YAG laser through the injector port and reflecting the beam off a conical mirror at the center of the piston. PIV data was difficult to obtain due to significant out-of-plane velocities. However, data was acquired at 25° and 15° before top dead center of compression at 750 rev/min.

The effects of spray targeting on mixing, combustion, and pollutant formation under a low-load, late-injection, low-temperature combustion (LTC) diesel operating condition are investigated by optical engine measurements and multi-dimensional modeling. Three common spray-targeting strategies are examined: conventional piston-bowl-wall targeting (152° included angle); narrow-angle floor targeting (124° included angle); and wide-angle piston-bowl-lip targeting (160° included angle). Planar laser-induced fluorescence diagnostics in a heavy-duty direct-injection optical diesel engine provide two-dimensional images of fuel-vapor, low-temperature ignition (H2CO), high-temperature ignition (OH) and soot-formation species (PAH) to characterize the LTC combustion process.

Homogeneous charge compression ignition (HCCI) combustion is considered to be an attractive alternative to traditional internal combustion engine operation because of its extremely low levels of pollutant emissions. However, there are several difficulties that must be overcome for HCCI practical use, such as difficult ignition timing controllability. Indeed, too early or too late ignition can occur with obvious drawbacks. In addition, the increase in cyclic variation caused by the ignition timing uncertainty can lead to uneven engine operation. As a way to solve the combustion phasing control problem, dual-fuel combustion has been proposed. It consists of a diesel pilot injection used to ignite a pre-mixture of gasoline (or other high octane fuel) and air. Although dual-fuel combustion is an attractive way to achieve controllable HCCI operation, few studies are available to help the understanding of its in-cylinder combustion behavior.

Homogeneous or partially premixed charge compression ignition combustion is considered to be an attractive alternative to traditional internal combustion engine operation because of its extremely low levels of pollutant emissions. However, since it is difficult to control the start of combustion timing, direct injection of fuel into the combustion chamber is often used for combustion phasing control, as well as charge preparation. In this paper, numerical simulations of compression ignition processes using gasoline fuel directly injected using a low pressure, hollow cone injector are presented. The multi-dimensional CFD code, KIVA3V, that incorporates various advanced sub-models and is coupled with CHEMKIN for modeling detailed chemistry, was used for the study. Simulation results of the spray behavior at various injection conditions were validated with available experimental data.

Multi-Dimensional modeling was carried out for a Mercury Marine two-stroke DISI engine. Recently developed spray, ignition, and combustion models were applied to medium load cases with an air-fuel ratio of 30:1. Three injection timings, 271, 291 and 306 ATDC were selected to investigate the effects of the injection timing on mixture formation, ignition and combustion. The results indicate that at this particular load condition, earlier injection timing allows more fuel to evaporate. However, because the fuel penetrates further toward the piston, a leaner mixture is created near the spark plug; thus, a slower ignition process with a weaker ignition kernel was found for the SOI 271 ATDC case. The measured and computed combustion results such as average in-cylinder pressure and NOx are in good agreements. The later injection case produces lower NOx emission and higher CO emission; this is due to poor mixing and is in agreement with experimental measurements.

Fuel preparation and stratified combustion were studied for a conceptual gasoline Direct-Injection Spark-Ignition (GDI or DISI) engine by computer simulations. The primary interest was on the effects of different injector orientations and the effects of tumble ratio for late injection cases at a partial load operating condition. A modified KIVA-3V code that includes improved spray breakup and wall impingement and combustion models was used. A new ignition kernel model, called DPIK, was developed to describe the early flame growth process. The model uses Lagrangian marker particles to describe the flame positions. The computational results reveal that spray wall impingement is important and the fuel distribution is controlled by the spray momentum and the combustion chamber shape. The injector orientation significantly influences the fuel stratification pattern, which results in different combustion characteristics.

Numerical simulations were performed to investigate the combustion process in the Premixed Compression Ignition (PCI) regime in a light-duty diesel engine. The CHEMKIN code was implemented into an updated KIVA-3V release 2 code to simulate combustion and emission characteristics using reduced chemistry. The test engine used for validation data was a single cylinder version of a production 1.9L four-cylinder HSDI diesel engine. The engine operating condition considered was 2,000 rev/min and 5 bar BMEP load. Because high EGR levels are required for combustion retardation to make PCI combustion possible, the EGR rate was set at a relatively high level (40%) and injection timing sweeps were considered. Since injection timings were very advanced, impingement of the fuel spray on the piston bowl wall was unavoidable. To model the effects of fuel films on exhaust emissions, a drop and wall interaction model was implemented in the present code.

A novel 2-zone combustion system was examined at medium load operation consistent with loads in the light duty vehicle drive cycle (7.6 bar BMEP and 2600 rev/min). Pressure rise rate and noise can limit the part of the engine map where pre-mixed combustion strategies such as HCCI or RCCI can be used. The present 2-zone pistons have an axial projection that divides the near TDC volume into two regions (inner and outer) joined by a narrow communication channel defined by the squish height. Dividing the near TDC volume provides a means to prepare two fuel-air mixtures with different ignition characteristics. Depending on the fuel injection timing, the reactivity of the inner or outer volume can be raised to provide an ignition source for the fuel-air mixture in the other, less reactive volume. Multi-dimensional CFD modeling was used to design the 2-zone piston geometry examined in this study.

In-cylinder fuel blending of gasoline with diesel fuel is investigated on a multi-cylinder light-duty diesel engine as a strategy to control in-cylinder fuel reactivity for improved efficiency and lowest possible emissions. This approach was developed and demonstrated at the University of Wisconsin through modeling and single-cylinder engine experiments. The objective of this study is to better understand the potential and challenges of this method on a multi-cylinder engine. More specifically, the effect of cylinder-to-cylinder imbalances and in-cylinder charge motion as well as the potential limitations imposed by real-world turbo-machinery were investigated on a 1.9-liter four-cylinder engine. This investigation focused on one engine condition, 2300 rpm, 5.5 bar net mean effective pressure (NMEP). Gasoline was introduced with a port-fuel-injection system.

In the current work, a series-hybrid vehicle has been constructed that utilizes a dual-fuel, Reactivity Controlled Compression Ignition (RCCI) engine. The vehicle is a 2009 Saturn Vue chassis and a 1.9L turbo-diesel engine converted to operate with low temperature RCCI combustion. The engine is coupled to a 90 kW AC motor, acting as an electrical generator to charge a 14.1 kW-hr lithium-ion traction battery pack, which powers the rear wheels by a 75 kW drive motor. Full vehicle testing was conducted on chassis dynamometers at the Vehicle Emissions Research Laboratory at Ford Motor Company and at the Vehicle Research Laboratory at Oak Ridge National Laboratory. For this work, the US Environmental Protection Agency Highway Fuel Economy Test was performed using commercially available gasoline and ultra-low sulfur diesel. Fuel economy and emissions data were recorded over the specified test cycle and calculated based on the fuel properties and the high-voltage battery energy usage.

High-speed video imaging in a swirl-supported (Rs = 1.7), direct-injection heavy-duty diesel engine operated with moderate-to-high EGR rates reveals a distinct correlation between the spatial distribution of luminous soot and mean flow vorticity in the horizontal plane. The temporal behavior of the experimental images, as well as the results of multi-dimensional numerical simulations, show that this soot-vorticity correlation is caused by the presence of a greater amount of soot on the windward side of the jet. The simulations indicate that while flow swirl can influence pre-ignition mixing processes as well as post-combustion soot oxidation processes, interactions between the swirl and the heat release can also influence mixing processes. Without swirl, combustion-generated gas flows influence mixing on both sides of the jet equally. In the presence of swirl, the heat release occurs on the leeward side of the fuel sprays.

This study investigates the potential of controlling premixed charge compression ignition (PCCI and HCCI) combustion strategies by varying fuel reactivity. In-cylinder fuel blending using port fuel injection of gasoline and early cycle direct injection of diesel fuel was used for combustion phasing control at both high and low engine loads and was also effective to control the rate of pressure rise. The first part of the study used the KIVA-CHEMKIN code and a reduced primary reference fuel (PRF) mechanism to suggest optimized fuel blends and EGR combinations for HCCI operation at two engine loads (6 and 11 bar net IMEP). It was found that the minimum fuel consumption could not be achieved using either neat diesel fuel or neat gasoline alone, and that the optimal fuel reactivity required decreased with increasing load. For example, at 11 bar net IMEP, the optimum fuel blend and EGR rate for HCCI operation was found to be PRF 80 and 50%, respectively.