Search Results

Nickel based superalloys have a wide range of applications due to high mechanical strength at high temperatures, fracture toughness and resistance to corrosion. However, because of their outstanding properties, it is considered as the difficult to machine materials. Inconel alloy X-750 is used extensively in rocket-engine thrust chambers. Airframe applications include thrust reversers and hot-air ducting systems along with large pressure vessels are formed from Inconel alloy X-750. Moreover, the comparative analysis of machinability aspect using coated carbide inserts is reported few. The current study explains the machinability investigation on Inconel alloy X-750 superalloys using coated carbides. To collect the experimental data, the L16 experimental design plan is used to experiment with a machining length of 40 mm.

The present work compares the tribological properties of ZnO (Zinc Oxide) nanoparticle based lubricant with ZDDP (zinc dialkyl dithiophosphate) based lubricant. The nanolubricant was prepared by mixing the nanoparticles in base oil followed by ultrasonification and ZDDP based lubricant was prepared by mixing ZDDP and stirring with base oil. Base oil used was mineral base oil. Both the lubricants were tested at three different temperatures, loads and roughness values. The test was carried out on AISI 52100 steel samples prepared by wire cutting and were grinded to three different levels of surface roughness. Friction and wear tests were performed using a reciprocating sliding tribo-tester at three different loads and temperatures. Taguchi orthogonal array was used to reduce the number of experiments. SEM, EDS and AFM analysis were carried out to study the surface wear phenomenon.

In the fabrication of parts in auto and aero segments, the use of ceramic (SiCp, Al2O3p) reinforces aluminum alloy found to be increased than that of steel and cast iron. This matrix-reinforced alloy has a high strength to weight ratio along with higher modulus and hardness, the lower thermal coefficient of expansion, and improved tribological properties. To this extent, this paper investigates the turning characteristics and optimization study of newly developed metal matrix composites by the addition of both hard ceramic SiCp and soft stable lubricant molybdenum disulfide (MoS2p). The samples such as Sample 1: AlSi10Mg/3SiCp, Sample 2: AlSi10Mg/2MoS2p and Sample 3: AlSi10Mg/3SiCp /2MoS2p are prepared using the automated stir-casting machine. The particles are observed to be uniformly distributed in the composite. After density and hardness measurement, the samples are subjected to machining, and the responses are optimized by using response surface method.

Lithium (Li)-based batteries have wide applications in the everyday gadgets. Li-based batteries have prominent usage in the automotive sector. All the major OEMs for manufacturing hybrid electric vehicles (HEVs) and electric vehicles (EVs) use only Li batteries and are still going to continue for the next decades. However, during the operation of these batteries, they are susceptible to environmental and battery factors. The amount of charge currently taken in or out influences the internal resistance and temperature of the battery. Therefore, the amount of heat generated by the Li-ion batteries during operation is critical for designing a cost-effective and efficient thermal management system (TMS) for HEVs and EVs.

Design and simulation analysis of braking system for ATV is carried out with the assistance of Ansys and MATLAB. Heat generated increases the temperature of the disc brake at the rubbing surface resulting in thermal stresses in the components of the braking system. Static, structural, thermal, computational flow dynamics, vibrational & fatigue behavior of ventilated brake disc rotor, hub and upright are analyzed. Stainless Steel, SS-410 material configuration has been considered for disc brake rotor and results obtained are analyzed in terms of performance, longevity and efficiency. Braking efficiency and stopping distance curve are analyzed from their characteristics plot. Vibrational behavior, structural behavior, thermal behavior, performance efficiency, flow behavior of ventilated disc brake rotor can be easily depicted with respect to bump and droop during acceleration, high climb and maneuverability. Ventilated disc brake Rotor with outer diameter of 220 mm is used.

Considerable weight of an automobile is constituted by the engine and there is scope for improvement in fuel efficiency and emission control through optimization of weight in the engine. In this work, AlSi10Mg alloy produced by the direct metal laser sintering (DMLS) is suggested for engine application which is a lightweight aluminum alloy. Mechanical properties like tensile strength, compressive strength, and hardness of both cast and DMLS manufactured alloy are compared followed by analysis of SEM images of tensile test fractured surfaces. Reciprocating wear test is carried out for one lakh cycles at 125°C temperature with SAE 40 grade oil as lubricant. Co-efficient of friction (COF), wear rate of the cast and DMLS manufactured samples are compared. Wear patterns are analyzed using SEM images of the wear tracks.

Friction Stir Welding (FSW) is a widely used solid state welding process in which its heats metal to the below recrystallization temperature due to frictional force. FSW mostly avoids welding defects like hot cracking and porosity which are mainly occur in conventional welding techniques. In this process the combination of frictional force and the mechanical work provide heating the base metal to get defect free weld joints. Aluminium Alloys 2014 and 6061 are generally used in a wide range of automobile applications like Engine valves and tie rod, shipbuilding, and aerospace due to their high corrosion resistance, lightweight, and good mechanical properties. In the present work, aluminium alloys of AA6061 and AA2014 were effectively welded by friction stir welding technique. The tool rotational speed, travel speed, and tool profile are the important parameters in FSW process. High Speed Steel (HSS) tool with Hexagonal profile is used for this joining.

The cross flow design of a radiator and its heat transfer and temperature drop was simulated then validated by using a data acquisition system during both static and dynamic running conditions of a Formula SAE car. The data acquisition system simulated and validated the radiator's cross flow design and heat transfer, as well as the temperature drop, under static and dynamic conditions in a car. The optimal radiator design determines the engine's operating temperature and the desired temperature drop gain through proper design of the inner core, number of fins and tubes, and radiator material. The purpose of a properly designed radiator is to prevent the combustion engine from heating up above its operating temperature [1]. The radiator's design is based on the operating temperature of the CBR 600RR engine. The highest temperature recorded was around 105°C, and in the worst case scenario, it can reach 110°C.

Epoxy carbon fiber composite materials are known for their light weight and high performance. They can be effective substitutes for commonly used materials for making drive shafts. Fiber orientation angle plays a major role in determining such a drive shaft’s responses. The responses considered in this paper are critical buckling torque, fundamental natural frequency and total deformation. A drive shaft made of epoxy carbon unidirectional prepreg is generated using ANSYS 18.0 ACP Composite Prepost. The objective of this paper is to determine an optimal configuration of fiber orientation angles for four, five and six-layered epoxy carbon drive shaft which tends to increase critical buckling torque and fundamental natural frequency while decreasing the total deformation. The optimal configuration which satisfies this objective for the three responses is identified by Minitab 17 statistical software.

The drastic technological advancements in the field of autonomous vehicles and connected cars lead to substantial progression in the commercial values of automobile industries. However, these advancements force the Original Equipment Manufacturers (OEMs) to shift from feedback-based reactive business analysis to operational-data based predictive analysis thereby enhancing both the customer satisfaction as well as business opportunities. The operational data is nothing but the parameters obtained from several parts of an automobile during its operation such as, temperature in radiator, viscosity of the engine oil and force applied over the brake disk. These operational data are gathered using several sensors implanted in different parts of an automobile and are continuously transmitted to backend computers to develop Digital Twin, which is a virtual model of the physical automobile.

A Formula Student race car is a car designed and manufactured for speed, performance, and competition. For a car to have high speed and performance, their parts also need to be lighter with being able to sustain the dynamically occurring stresses. Effective braking is a crucial factor which determines the performance of the car. This paper focuses on designing a brake caliper on the basis of calculations done with respect to a Formula Student race car, selecting a material which is of low density but with higher strength which can be easily manufactured with low cost and analyzing the design. Further, the manufactured part is also tested statically to ensure proper working before being tested on an actual formula student race car. The caliper is again tested dynamically, where the caliper is mounted on rear wheels of the car. To ensure proper working, brake pressure sensors are being mounted which also helps to validate the calculations.

This paper describes the design of a novel pneumatic gear shifting system to replace the existing gear stick manual shifting system for ease of the driver while shifting gears. The aim of this work is to have a semi-automatic shifting (pneumatic shifting) removing the need for the driver clutch operation. The system consists of a solenoid valve, CO2 gas-pressurized cylinder, double-acting cylinder, and single-acting cylinder. On basis of the signal received the gear needs to be changed, the shifter opens or closes a magnetic valve assembly. The solenoid valve allows the compressed air into the piston that comes from a pressurized cylinder, in order to create the effect of shifting gears. The pedal shifter and buttons are used to shift the gears. The pedal shifter was designed by using a 3-D printing technique using PLA material. The microcontroller used is ATMEGA-328 in this system. There are three switches, one for upshift, downshift, and clutch respectively.

Body motions of flying animals can be very complex, especially when the body parts are greatly flexible and they interact with the surrounding fluid. The wing kinematics of an animal flight is governed by a large number of variables and thus the measurement of complete flapping flight is not so simple, making it very complex to understand the contribution of each parameter to the performance and hence, to decide the important parameters for constructing the kinematic model of a bat is nearly impossible. In this paper, the influence of each parameter is uncovered and the variables that a specified reconstruction of bat flight should include in order to maximally reconstruct actual dimensional complexity, have been presented in detail. The effects of the different kinematic parameters on the lift coefficient are being resulted.

The final drivetrain ratio is an essential part of a vehicle. It is responsible for providing the desired torque to overcome obstacles while maintaining the speed and acceleration of a vehicle. A vehicle must have an optimum gear ratio to obtain the desired velocity and acceleration. To achieve this, four different approaches were used considering the input parameters of a BAJA All-Terrain Vehicle (ATV). The traction received from the ground is calculated and plotted against velocity on different terrains. Further, a drivetrain was modeled in Simulink to obtain different parameters like vehicle speed, acceleration, and wheel slip. A range of gear ratios was obtained by following a similar trend of vehicle parameters that were best suited for improving vehicle performance. Graphs were plotted to compare the effect of various vehicle parameters, and an optimum gear ratio was obtained.

Digital data extraction is the most important and advance informative system that are embedded in the modern world functioning machinery to acquire the most precise feedback about the real-time operational situation of the machine to the control centre of operation. This data that is acquired from the machinery can be used to increase the efficiency, operational timing, production-cost and the overall human effort that is required for the operation. This paper focuses on the development on the advanced telemetry system that is capable to acquire real-time data of the modern vehicle wirelessly during its motion. A mobile automotive telemetry system for installation on-board a vehicle, includes: diagnostic structure for monitoring operational functions of the vehicle and generating operational information; memory for storing the generated operational information; and a server, in communication with the diagnostic structure and the memory.

The main purpose of this study is to investigate additive manufactured Inconel super alloy subjected to cryogenic treatment (CT). Cryogenic treatment is mainly used in aerospace, defense and automobile application. Direct metal laser sintering is an additive manufacturing technique used for manufacturing of complex and complicated functional components. Inconel is an austenitic chromium nickel based super alloy often used in the applications which require high strength & temperature resistant. In this work, a study is carried out on microstructure and mechanical properties of additive manufactured Inconel 718 when subjected to cryogenic treatment at three different time intervals. The micro-structural evolution of IN718 super-alloy before and after CT was investigated by both optic microscope and scanning electron microscope. Surface roughness and hardness at different CT time intervals has also analyzed. Additionally, XRD technique was used to analyze the surface residual stress.

Permanent magnet brushed DC (PMBDC) motors are mostly preferred in many automotive applications because of better power density and easier control. Five different automotive applications such as electric parking brake (EPB), power seat, power window, sunroof drive, and tire air pump are chosen and discussed in this paper. A step-by-step electromagnetic analysis is carried out for all the designed models. Low-cost ferrite-based magnets are used for cost reduction keeping the efficiency as high above 77% in all the models. Comparison on performance and cost are discussed in the conclusion section.

This paper describes the modelling and electromagnetic analysis of Permanent Magnet Brushed Direct Current (PMBDC) motor using Finite Element Analysis (FEA) software packages. The designed motors referred in this analysis are fit for use in applications of the electronic throttle control and exhaust gas recirculation in automobiles. Performances of the designed PMBDC models are compared with the traditionally used machines. Three PMBDC models with different operating characteristics are proposed for the two applications. Each model is suitable for use in both applications. Cost analysis of the motors is also carried out, and comparison with the traditionally used machines is done.

In the present paper, to predict the process relation between laser-assisted machining parameters and machinability characteristics, statistical models are formulated by employing surface response methodology along with artificial neural network. Machining parameters such as speed of cut; the rate of feed; along with the power of laser are taken as model input variables. For developing confidence limit in collected raw experimental data, the full factorial experimental design was applied to cutting force; surface roughness; along with flank wear. Response surface method (RSM) with the least square method is used to develop the theoretical equation. Furthermore, artificial neural network method has been done to model the laser-assisted machining process. Then, both the models (RSM and ANN) are compared for accuracy regarding root mean square error (RMSE); model predicted error (MPE) along with the coefficient of determination (R2).

In recent years, aluminum metal matrix composites (Al-MMC) are found as a potential material for numerous applications owing to its excellent tribological and mechanical properties. In this work, the machining characteristics of aluminum alloy (Al7075) reinforced with TiC/MoS2 having nanoparticle has been studied. The samples of aluminum metal matrix composites by varying TiC in 0, 2 and 4 and MoS2 in 0 and 2 of the percentage weight of aluminum alloy (Composite 1(Al7075), Composite 2 (Al7075/2TiC/2MoS2) and composite 3 (Al7075/4TiC/2MoS2), respectively) are fabricated by the stir-casing method. The turning characteristics of the developed metal matrix composites are studied at various parameters such as cutting velocity (30 m/min, 60 m/min and 90 m/min), cutting depth (0.5 mm, 1.0 mm and 1.5 mm) and composites (1, 2 and 3) using TiN coated cutting tool by dry turning at 0.05 mm/rev feed rate.