Search Results

Abstract The ASTM D130 was first issued in 1922 as a tentative standard for the detection of corrosive sulfur in gasoline. A clean copper strip was immersed in a sample of gasoline for three hours at 50°C with any corrosion or discoloration taken to indicate the presence of corrosive sulfur. Since that time, the method has undergone many revisions and has been applied to many petroleum products. Today, the ASTM D130 standard is the leading method used to determine the corrosiveness of various fuels, lubricants, and other hydrocarbon-based solutions to copper. The end-of-test strips are ranked using the ASTM Copper Strip Corrosion Standard Adjunct, a colored reproduction of copper strips characteristic of various degrees of sulfur-induced tarnish and corrosion, first introduced in 1954. This pragmatic approach to assessing potential corrosion concerns with copper hardware has served various industries well for a century.

Abstract In the United States (USA), transportation is the largest single source of greenhouse gas (GHG) emissions, representing 27% of total GHGs emitted in 2020. Eighty-three percent of these came from road transport, and 57% from light-duty vehicles (LDVs). Internal combustion engine (ICE) vehicles, which still form the bulk of the United States (US) fleet, struggle to meet climate change targets. Despite increasingly stringent regulatory mechanisms and technology improvements, only three US states have been able to reduce their transport emissions to the target of below 1990 levels. Fifteen states have made some headway to within 10% of their 1990 baseline. Largely, however, it appears that current strategies are not generating effective results. Current climate-change mitigation measures in road transport tend to be predominantly technological.

Abstract This article discusses a multi-item planning and scheduling problem in a job-shop system with consideration of energy consumption. Planning is considered by a set of periods, each one is characterized by a demand, energy, and length. Scheduling is determined by the sequences of jobs on available resources. A Mixed-Integer Linear Programming (MILP) problem is formulated to integrate planning and scheduling, it is considered as an NP-difficult problem. A Genetic Algorithm (GA) is then developed to solve the MILP, and then a hybridized approach of simulated annealing with genetic algorithm (HGASA) is presented to optimize the results. Finally, numerical results are presented and analyzed to evaluate the effectiveness of the proposed algorithms.

Abstract The United Nation Economic Commission for Europe (UNECE) Regulation 155—Cybersecurity and Cybersecurity Management System (UN R155) mandates the development of cybersecurity management systems (CSMS) as part of a vehicle’s lifecycle. An inherent component of the CSMS is cybersecurity risk management and assessment. Validation and verification testing is a key activity for measuring the effectiveness of risk management, and it is mandated by UN R155 for type approval. Due to the focus of R155 and its suggested implementation guideline, ISO/SAE 21434:2021—Road Vehicle Cybersecurity Engineering, mainly centering on the alignment of cybersecurity risk management to the vehicle development lifecycle, there is a gap in knowledge of proscribed activities for validation and verification testing.

Abstract This article proposes a novel approach of a hybrid system of physics and data-driven modeling for accurately estimating the state of charge (SOC) of a battery. State of Charge (SOC) is a measure of the remaining battery capacity and plays a significant role in various vehicle applications like charger control and driving range predictions. Hence the accuracy of the SOC is a major area of interest in the automotive sector. The method proposed in this work takes the state-of-the-art practice of Kalman filter (KF) and merges it with intelligent capabilities of machine learning using neural networks (NNs). The proposed hybrid system comprises a physics-based battery model and a plurality of NNs eliminating the need for the conventional KF while retaining its features of the predictor-corrector mechanism of the variables to reduce the errors in estimation.

Abstract With the introduction of advanced lightweight materials with complex microstructures and behaviors, more focus is put on the accurate determination of their forming limits, and that can only be possible through experiments as the conventional theoretical models for the forming limit curve (FLC) prediction fail to perform. Despite that, CAE engineers, designers, and toolmakers still rely heavily on theoretical models due to the steep costs associated with formability testing, including mechanical setup, a large number of tests, and the cost of a stereo digital image correlation (DIC) system. The international standard ISO 12004-2:2021 recommends using a stereo DIC system for formability testing since two-dimensional (2D) DIC systems are considered incapable of producing reliable strains due to errors associated with out-of-plane motion and deformation.

Abstract The hydrocarbons constituting the heavy tail of gasoline are key contributors to particulate matter (PM) emissions from spark-ignition (SI) engines. They are predominantly aromatic and, to a significant degree, bicyclic aromatic. For example, above a boiling point of 400°F, the content of bicyclic compounds in the United States (US) summer E10 regular-grade gasoline exceeds 50%v. Various gasoline parameters, such as the PM Index, Particulate Evaluation Index (PEI), Particulate and Soot Correlation Equation (PASCE), or Threshold Sooting Index (TSI), have been proposed as predictors of PM emissions from SI engines. In particular, the PM Index, whose value is dominated by the content of heavy aromatics and which, so far, has yielded the most predictive PM emissions models, appears to be the best metric to achieve this objective.

Abstract The 2010 Environmental Protection Agency (EPA) Emission Standard for heavy-duty engines required 0.2 g/bhp-hr over certification cycles (cold and hot Federal Test Procedure [FTP]), and the California Air Resources Board (CARB) standards require 0.02 g/bhp-hr for the same cycles leading to a 90% reduction of overall oxides of nitrogen (NOx) emissions. Similar reductions may be considered by the EPA through its Cleaner Trucks Initiative program. In this article, aftertreatment system components consisting of a diesel oxidation catalyst (DOC); a selective catalytic reduction (SCR) catalyst on a diesel particulate filter (DPF), or SCR-F; a second DOC (DOC2); and a SCR along with two urea injectors have been analyzed, which could be part of an aftertreatment system that can achieve the 0.02 g/bhp-hr standard.

Abstract Heavy-duty (HD) diesel engines are the primary propulsion systems in use within the transportation sector and are subjected to stringent oxides of nitrogen (NOx) and particulate matter (PM) emission regulations. The objective of this study is to develop a robust calibration technique to optimize HD diesel engine for performance and emissions to meet current and future emissions standards during certification and real-world operations. In recent years, California - Air Resources Board (C-ARB) has initiated many studies to assess the technology road maps to achieve Ultra-Low NOx emissions for HD diesel applications [1]. Subsequently, there is also a major push for the complex real-world driving emissions as the confirmatory and certification testing procedure in Europe and Asia through the UN-ECE and ISO standards.

Abstract Lightweight and high-strength high-pressure die casting (HPDC) aluminum has been widely used in automotive components such as the cylinder block, lower crankcase extension, transmission case, and drive unit. Die cast parts have good surface finishes with relatively higher material strength in the casting skin than the center core material, maintain consistent features and tolerance, and maximize metal yield, therefore making it the most cost-effective casting process for mass production of aluminum parts. However, due to the rapid filling rates, the HPDC process tends to form large porosity and oxides because of the entrapped gas and solidification shrinkage, thereby deteriorating the mechanical properties of the casting parts.

Abstract Safety is always a crucial aspect of developing autonomous systems, and the motivation behind this project comes from the need to address the traffic crashes occurring globally on a daily basis. The present work studies the coexistence of the novel rule-based behavioral planning framework with the five key advanced driver assistance system (ADAS) features as proposed in this article to fulfill the safety requirements and enhance the comfort of the driver/passengers to achieve a receding-horizon autopilot. This architecture utilizes data from the sensor fusion and the prediction module for the prediction time horizon of 2 s iteratively, which is continuously moving forward (hence, the receding horizon), and helps the behavior planner understand the intent of other vehicles on the road in advance.

Abstract In this work, an in situ multispecies portable emission measurement system (PEMS) is presented. The system is based on tunable diode laser absorption spectroscopy (TDLAS) and is capable of measuring tailpipe emissions without the necessity of online calibration. It is intended for application on passenger cars within the real drive emission (RDE) procedure of the Worldwide Harmonized Light Duty Test Procedure (WLTP). In contrast to the extractive measurement principles of commercially available PEMS, the introduced measurement system does not require gas sampling or preconditioning and thus does not suffer from the same low-pass filter effects on the measurements. These differences are suspected to have an impact on certification-relevant measurement data. Measurements have been conducted on a 3-cylinder 1 liter EURO 6 b gasoline engine test bench to investigate the differences between the presented measurement system and a commercially available PEMS.

Abstract The variation of inflation pressure has an important effect on the longitudinal slip characteristics of tires that can affect the braking performance of the vehicle, so the influence of inflation pressure should be taken into account in high-precision tire models. However, the effects of inflation pressure and vertical load on tire force and moment characteristics are usually coupled. When the inflation pressure is changing while keeping the load constant, the tire contact patch and carcass stiffness will change at the same time, so the contribution of tread and carcass to tire traction properties cannot be decoupled so that the tire design cannot be well guided. On the contrary, if the vertical loading method is changed, the vertical deflection control is used instead of load control.

Abstract The increased scope of active and passive safety in motor vehicles and the enforcement of approval requirements for individual parts and assemblies affect the design and parameters of a car’s motion. The tire, which transmits forces and torques onto the road’s surface is a particularly crucial element in the vehicle. Its structure, type of mixture, and operating conditions determine the safety of vehicle motion. The three-axial force system loads the tires of the car and affects both the tread and sidewall, as well as the suspension and steering system. Taking into account the controllability and stability of movement, the tire is subjected to dynamic and thermal loads, as well as to wear and random damage. This negatively impacts on the joints of composite layers. The sudden loss of pressure in the tire can lead to serious accidents, especially when moving at high speeds, due to changes in the rolling radius.

Abstract In automotive, the use of heavy structure leads to high consumptions of fuel and resulting high exhaust (CO2) emissions. To curb this problem, nowadays, the conventional steel used for years in automotive structures is currently replaced with other different lightweight materials such as aluminum, magnesium, glass fiber-reinforced polymer, carbon fiber-reinforced polymer, titanium, and so on. On the other hand, compared to the known steel properties and performances, these lightweight materials offer challenging issues related to life cycle, recycling, cost, and manufacturing. But, more than sometimes, reaching the same levels of performances with materials different from steel presents huge difficulties. This represents the cause of researching strategies and techniques to optimize the material distribution and the performances of a component, saving material and consequently reducing weight.

Abstract The lubricating properties of diesel are an imperative aspect for the optimal functioning of fuel injection components. Regulatory standards followed by refineries utilize accelerated wear testing methodologies. These tests provide indicative results for judging the lubricity but are not conclusive for determining wear in functional applications attributed to higher loads and other environmental factors. In the course of this article, a tribological evaluation was carried out on Low-Sulfur Diesel (LSD) and Ultralow Sulfur Diesel (ULSD) by utilizing modified test parameters incorporating higher loads and a more extensive gradient of temperature on High-Frequency Reciprocating Rig (HFRR) tribotester. The variance in the resultant coefficient of friction (COF) and wear scar concerning the change in parameters was observed as well as a comparative analysis was drawn between both test fuels.

Abstract Automated guided vehicle systems (AGVS) are the prominent one in modern material handling systems used in small manufacturing enterprises (SMEs) due to their exciting features and benefits. This article pinpoints the need of AGVS in SMEs by describing the material handling selection in SMEs and enlightening recent technological developments and approaches of the AGVS. Additionally, it summarizes the analytical and simulation-based tools utilized in design problems of AGVS along with the influence of material handling management and key hurdles of AGVS. The current study provides a limelight towards making smart automated guided vehicles (AGVs) with the simplified and proper routing system and favorable materials and more importantly reducing the cost and increasing the flexibility.

Abstract Accelerated durability testing of automotive components has become a major interest for the ground vehicle Industries. This approach can predict the life characteristics of the vehicle by testing fatigue failure at higher stress level within a shorter period of time. Current tradition of laboratory testing includes a rigid fixture to mount the component with the shaker table. This approach is not accurate for the durability testing of most vehicle components especially for those parts connected directly with the tire and suspension system. In this work, the effects of the elastic support on modal parameters of the tested structure, such as natural frequencies, damping ratios and mode shapes, as well as the estimated structural fatigue life in the durability testing were studied through experimental testing and numerical simulations.

Abstract Wireless Power Transfer (WPT) is presently being applied to consumer electronics in the low-power range and is planned to be commercialized in the high-power range for plug-in and electric vehicles in 2018. There are, however, many technology challenges remaining before widespread implementation of high-power WPT will occur. The SAE Vehicle Wireless Power and Alignment Taskforce published the Technical Information Report J2954 in 2016 to help harmonize the first phase of high-power WPT technology development. SAE J2954 adopts a performance-based approach to standardizing WPT by specifying ground and assembly coils to be used in a test stand (per Z-class) to validate performance, interoperability and safety. The main goal of this SAE J2954 bench testing campaign was to prove interoperability between WPT systems utilizing different coil magnetic topologies for SAE TIR J2954.

Abstract Closed field testing of Connected and Automated Vehicles (CAV) is an essential pillar for verifying the functionality and performance of CAV and promoting its large-scale deployment. Recently, many closed test fields in the world have been newly built or rebuilt for testing CAV such as M-City in USA and AstaZero in Sweden. However, few construction methods, standards, and specifications of closed test fields for testing CAV were reported with details. We propose the construction practice of the Closed Connected and Automated Vehicles Test Field (CAVTest) of Chang’an University in China. The CAVTest has a multilayer architecture, from down to the top, which consists of an application scenario layer, a perception and a physical communication layer, a network link layer, and a management service layer, respectively.