Search Results

Wireless power transfer (WPT) of plug-in and battery electric vehicles (PEV�s) rely on loosely coupled transformer operating in magnetic resonance to tune out reactive effects. Depending on the degree of coupling, such systems experience a single peak response that trends to bifurcate as the coefficient of coupling increases. This places additional burden on the WPT grid side power controller to not only manage the power transfer process but to manage the transmit coil to receiver coil reactive power in response to vehicle ground clearance and misalignment tolerance. In addition, the WPT rectified output voltage must dynamically match the vehicle on-board regenerative energy storage system (RESS). This paper examines the essentials of WPT operation and challenges facing the commercialization of wireless charging. Experimental results obtained from the Oak Ridge National Laboratory WPT apparatus are presented as validation of the theory. Presenter John Miller, ORNL

Auto manufacturers have known and surveys confirm that consumers require short payback periods (2-4 years) for investments in fuel economy. Using societal discount rates, engineering-economic generally find substantial potential to increase fuel economy, cost-effectively. This phenomenon, often referred to as the ?energy paradox?, has been observed in nearly all consumers? choices of energy-using durable goods. Loss aversion, perhaps the most well established theory of behavioral economics, provides a compelling explanation. Engineering economic analyses generally overlook the fact that consumers? investments in fuel economy are not sure things but rather risky bets. Future energy prices, real world on-road fuel economy, and many other factors are uncertain. Loss aversion describes a fundamental human tendency to exaggerate the potential for loss relative to gain when faced with a risky bet. It provides a sufficient explanation for consumers?

Many manufacturing companies want to apply AFP technology to complex high-curvature part shapes. As new AFP machine technologies are developed to specifically apply material over complex shapes, new and innovative NC programming approaches are needed to successfully, reliably, and accurately apply material with good consolidation, while meeting the fiber direction and coverage requirements. A big issue with AFP is the production rate vs. part complexity. Most complex shapes can be created with a single .125? wide strip (tow) of material. But the production time would be impractically long. So machine builders create 6, 8, 16, even 32 tow AFP heads, and use the widest tow possible for the highest laydown rates. But then wide compaction rollers on these systems have difficulty consolidating material over curved surfaces, and the minimum steering radius of wider tows challenge the software?s ability to meet the layup requirements.

Update on light-duty regulations. Presenter Michael J. McCarthy, California Air Resources Board

Automakers, suppliers, public agencies, interest groups and others are increasingly embracing the environment as one of the dominant forces in the US automotive market. All parties have a strong vested interest in understanding how environmental concerns will influence design, production, marketing and usage of tomorrow�s vehicles. A common need of all parties is independent and actionable information to enable them to make better decisions and have the greatest chance of being successful in this uncertain future. Four factors - an uncertain economic climate; a constantly changing governmental regulatory system; advancements in powertrain technology; and ever-present environmental concerns - continue to shape the automotive landscape. While automakers are focused on developing alternative powertrains and alternative fuel options for an increasingly �green� vehicle market, J.D.

Engine Boosting Systems. Presenter Andrew Williams, Loughborough Univ.

Developing relatively cheap and widely available resources for heterogeneous solid catalyst synthesis is a promising approach for biodiesel fuel industry. Seashell which is essentially calcium carbonate can be used as a basic support for transesterification heterogeneous catalysts. In the present investigation, the alcoholysis of waste frying oil has been carried out using seashell-supported K3 PO4 as solid catalyst. Presenter Essam Oun Al-Zaini, PhD student, UNSW

Toyota is committed to the development of advanced powertrains to help address concerns with future oil supplies, the impacts of increased carbon dioxide emissions, and air pollution. Towards that end Toyota is planning to bring to market in 2012 a plug-in hybrid vehicle, a short range electric vehicle, a long range electric vehicle and in the 2015 timeframe hydrogen powered fuel cell vehicle. This presentation will focus on our electric vehicle plans and the challenges with bringing electric vehicle to the market. From the 2010 Alt Fuels Study, Toyota has identified that two key barriers for EV adoption are the times to charge the vehicle, and electricity cost. The study finds that the current infrastructure could be sufficient for most driving needs but EV drivers will still need to alter their driving habits slightly.

From 2009 until present Toyota has had a demonstration program of Prius PHV which is comprised of 600 vehicles throughout Japan, Europe and in the US. The vehicles were given to government agencies, corporations, utility companies and private individuals to use. With these demo units Toyota wanted to understand the market reaction and real world impact of plug-in technology on gasoline displacement with increased use of electricity as a fuel. This presentation shows that approximately 50% of fuel was saved using the PHVs in the US. An experiment in Toyota City shows that if public infrastructure is optimized to be convenient and located where people normally park, there is a potential to achieve an ideal fuel savings of 61%. The demonstration program shows that plug-in technology in fact saves fuel and that the proper infrastructure can optimize the fuel savings of plug-in hybrids. Presenter Avernethy Francisco, Toyota

Ford's EcoBoost GTDI engine technology (Gasoline Direct Injection, Turbo-charging and Downsizing) is being successfully implemented in the market place with the EcoBoost option accounting for significant volumes in vehicle lines as diverse as the F150 pickup truck, Edge CUV and the Lincoln MKS luxury sedan. A logical question would be what comes after GTDI? This presentation will review some of the technologies that will be required for further improvements in CO2, efficiency and performance building on the EcoBoost foundation as well as some of the challenges inherent in the new technologies and approaches. Presenter Eric W. Curtis, Ford Motor Co.

There are now a wide variety of Hybrid and Electric Vehicles in or near production. They reduce or displace petroleum consumption with of various combinations of conventional IC engine, mechanical transmission, liquid fuel storage, electrical energy storage, electrical and electro-mechanical energy conversion, and vehicle-to-grid energy interface. These Electrified types of vehicles include Mild Hybrid, Full Hybrid, Plug-In Hybrid, Extended Range Electric, and Battery Electric. Some types differ in their actual usability for the real mixes of driving trips, and further that differ in their effectiveness to reduce or displace fuel in actual real world driving use. Vehicle size is also a factor in total vehicle utility in transporting people. If we may segment drivers by their driving needs, in each segment, we see a particular type of electrified vehicle that is better suited than others at minimizing fuel cost and petroleum consumption for the purposes of transporting people.

Gasoline engines continue to suffer from significant pumping losses despite decades of effort focused on reducing throttling. Honeywell Turbo has developed a throttle with an integrated turbine/generator that generates electricity by recovering pumping work. This energy offsets power normally provided by the crank driven alternator, thereby saving fuel. It integrates well with modern electrical systems which employ smart charging and idle stop strategies. The ThrottleCharger provides fuel economy benefits up to 5% over federal test cycles and in real world conditions. Presenter Mike Guidry, Honeywell Int'l (Turbo Technologies)

The presentation describes the aerodynamic development and optimization process of the three different new models of the Audi A6/A7 family. The body types of these three models represent the three classic aerodynamic body types squareback, notchback and fastback. A short introduction of the flow structures of these different body types is given and their effect on the vehicle aerodynamic is described. In order to achieve good aerodynamic performance, the integration into the development process of the knowledge about these flow phenomena and the breakdown of the aerodynamic resistance into its components friction- and pressure drag as well as the induced drag is very important. The presentation illustrates how this is realized within the aerodynamic development process at Audi. It describes how the results of CFD simulations are combined with wind tunnel measurements and how the information about the different flow phenomena were used to achieve an aerodynamic improvement.

This session covers topics regarding new CI and SI engines and components. This includes analytical, experimental, and computational studies covering hardware development as well as design and analysis techniques. Presenter Sung Hoon Lee, Hyundai Motor Co.

Over the past several years, new recommended practices for testing plug-in vehicles have been developed by SAE standards committees. At first only proprietary or prototype vehicles were available to validate new procedures. However, with the recent availability of Chevy Volt and Nissan Leaf, these test procedures were put to the test in Argonne�s National Laboratory�s dynamometer test facility. Procedures for the Volt were according to the SAE J1711 procedures. The Leaf was tested according to procedures still under development in the SAE J1634 task force. Identified were aspects of the tests that were successful and areas where more development is needed. As described in SAE J2841, the Volt results were analyzed using a �utility factor� to estimate in-use expectations of electric-only miles.

This study evaluates utilizing an accelerated test method that correlates customer interaction with a vehicle seat where bagginess and wrinkling is produced. The evaluation includes correlation from warranty returns as well as test vehicle results for test verification. Consumer metrics will be discussed within this paper with respect to potential application of this test method, including but not limited to JD Power ratings. The intent of the test method is to aid in establishing appropriate design parameters of the seat trim covers and to incorporate appropriate design measures such as tie downs and lamination. This test procedure was utilized in a Design for Six Sigma (DFSS) project as an aid in optimizing seat parameters influencing trim cover performance using a Design of Experiment approach. Presenter Lisa Fallon, General Motors LLC

The U.S. Environmental Protection Agency (EPA) contracted with FEV, Inc. to estimate the per-vehicle cost of employing selected advanced efficiency-improving technologies in light-duty motor vehicles. The development of transparent, reliable cost analyses that are accessible to all interested stakeholders has played a crucial role in establishing feasible and cost effective standards to improve fuel economy and reduce greenhouse gas (GHG) emissions. The FEV team, together with engineering staff from EPA's National Vehicle and Fuel Emissions Laboratory, and FEV's subcontractor, Munro & Associates, developed a robust costing methodology based on tearing down, to the piece part level, relevant systems, sub-systems, and assemblies from vehicles ?with and without? the technologies being evaluated.

“Spotlight on Design” features video interviews and case study segments, focusing on the latest technology breakthroughs. Viewers are virtually taken to labs and research centers to learn how design engineers are enhancing product performance/reliability, reducing cost, improving quality, safety or environmental impact, and achieving regulatory compliance. Fuel efficiency, or simply put, how to get more mileage out of the same amount of fuel has become one of the main goals to be achieved by new automotive technologies in the future, thanks in part to new government regulations. In the episode “Fuel Efficiency: Racing toward CAFE 2025” (21:24) AVL engineers show simulation and testing being used to design more fuel efficient vehicles, including the equipment that actually analyzes fuel economy.

“Spotlight on Design” features video interviews and case study segments, focusing on the latest technology breakthroughs. Viewers are virtually taken to labs and research centers to learn how design engineers are enhancing product performance/reliability, reducing cost, improving quality, safety or environmental impact, and achieving regulatory compliance. In the episode “Composite Materials: Advanced Materials and Lightweighting” (30:20), Molded Fiber Glass Companies, known for its deep involvement in the creative development of the molded fiberglass process for the Corvette, demonstrates the manufacturing of sheet molded composite for fiberglass parts. Tanom Motors introduces the Tanom Invader, a blend between an automobile and a motorcycle made exclusively with composite materials. Finally, Euro-Composites demonstrates the manufacturing of honeycomb core material made out of aramid paper and phenolic resin used in aircraft structures.

“Spotlight on Design” features video interviews and case studies, focusing on technology breakthroughs, hands-on testimonials, and the importance of fundamentals. Viewers are virtually taken to industry labs and research centers to learn how design engineers solve real-life problems. These challenges include enhancing product performance, reducing cost, improving quality and safety, while decreasing environmental impact, and achieving regulatory compliance. In the episode “Automotive Charging Infrastructure: Vehicle and Grid Integration” (21:00), engineers from NextEnergy and an infrastructure expert from General Motors explain how technologies are rapidly converging to power electric vehicles and support the overall electric grid. This episode highlights: How the fast expansion of charging infrastructure is changing the way electric and hybrid-electric vehicles are gaining the confidence of consumers.