Search Results

This paper discusses the technology, components and systems incorporated in the design of the LM1600 I/CR marine gas turbine propulsion system as well as describing some of the novel and imaginative ways that the highly acclaimed F404 fighter aircraft engine has been modified and adapted to provide the nucleus for this sophisticated marine propulsion system. Specifically, the modifications to the compressors, the high and low pressure turbines and the power turbine design characteristics are described. The proven materials technology from the highly successful LM2500 marine gas turbine has been applied to this engine as well.

Researchers now have the means to evolve complex manned and unmanned space missions using all of their complex support systems in a fully adaptive visual environment. The expected interactive nature of space missions requires powerful, flexible and comprehensive simulation hardware and software to develop and verify concepts, systems, and procedures. Correlation of visual, sensor, and radar imagery is essential due to new sensor blending and fusion techniques that characterize complex systems and missions. Only through total visual, non-visual and mission environment simulation, combined with analytical tools, can reliable systems and missions be developed. The same can be said of the simulation-based training programs that must be developed for ground and flight mission crews. If maximum situational awareness cannot be trained through simulation, it may be too risky, too expensive or even too late to acquire during a mission.

System level design studies of space applications ranging in power from 77 kWt to 200 MWt have indicated no practical limit to the thermal power that can be reliably generated by a space reactor system based on the technologies being developed in the SP-100 program. These technologies include uranium nitride fuel, PWC-11/rhenium bonded fuel cladding, PWC-11 structural material for the lithium coolant boundary, electromagnetic coolant pumps, safety and reactivity control drive mechanisms, sensors, shielding materials, etc. at operating temperatures up to 1400K. The physical arrangements and characteristics of the nuclear reactor materials are described. The physical size of components and the arrangement of components change, but the basic technologies required are generally the same, irrespective of the total power output.

The SP-100 Space Reactor Power System is being developed by GE, under contract to the U.S. Department of Energy, to provide electrical power in the range of 10's to 100's of kW. The system represents an enabling technology for a wide variety of earth orbital and interplanetary science missions, nuclear electric propulsion (NEP) stages, and lunar/Mars surface power for the Space Exploration Initiative (SEI). An effective infrastructure of Industry, National Laboratories and Government agencies has made substantial progress since the 1988 System Design Review. Hardware development and testing has progressed to the point of resolving all key technical feasibility issues. The technology and design is now at a state of readiness to support the definition of early flight demonstration missions. Of particular importance is that SP-100 meets the demanding U.S. safety, performance, reliability and life requirements.

This paper describes the design, implementation, and performance test results of an engineering model of the Position Multiplexer (MUX)-Analog Input Processor (AIP) System for the transmission and continuous measurements of Reflector Control Drive position in SP-100. The specially tailored MUX-AIP combination multiplexes the sensor signals and provides an increase in immunity from low frequency interference by translating the signals up to a higher frequency band. The modulated multiplexed signals are transmitted over a single twisted shielded cable pair from the reflector drives located near reactor to the AIP located at the power conditioning/system controller end of the space craft boom. There the signals are demultiplexed and processed by the AIP, eliminating the need for individual cables for each of the twelve position sensors across the boom.

The term “SP-100” is synonymous with a set of technologies that can be utilized to provide long lifetime, reliable, safe space power over the range of kilowatts to megawatts [1] using a nuclear reactor as the heat source. This paper describes recent development progress in a number of technology areas such as fuel, materials, reactivity control mechanisms and sensors. Without exception, excellent technical progress is being accomplished in all areas under development to optimize spacecraft performance characteristics.

Recent Generic Flight System (GFS) updates have necessitated revisions in the initial startup and restart control strategies. The design changes that have had the most impact on the control strategies are the addition of the Auxiliary Cooling and Thaw (ACT) system for preheating the lithium filled components, changes in the reactivity worths of the reflectors and safety-rods such that initial cold criticality is achieved with only a small amount of reflector movement following the withdrawal of the safety-rods, and the removal of the scram function from the reflectors. Revised control and operating strategies have been developed and tested using the SP-100 dynamic simulation model, ARIES-GFS. The change in the total reactivity worths of the reflectors and safety-rods has eliminated the need for the use of fast and slow reflector drive speeds during the initial on-orbit approach to criticality.

The approach that was utilized to start up and requalify manufacture of the thermoelectric unicouple devices for the Cassini RTG (Radioisotope Thermoelectric Generator) program are described in this paper. Key elements involved in this effort were: engineering review of specifications; training of operators; manufacturing product verification runs; and management review of results. Appropriately, issues involved in activating a fabrication process that has been idle for nearly a decade, such as upgrading equipment, adhering to updated environmental, health, and safety requirements, or approving new vendors, are also addressed. The cumulative results of the startup activities have verified that a production line for this type of device can be reopened successfully.

The SP-100 reactor will operate at temperatures up to 1500K in high vacuum. Development of bearing coatings is necessary to avoid self welding and/or galling of moving components. No experience base exists for these conditions-the early SNAP (Space Nuclear Auxiliary Power) program requirements were over 400K lower with shorter lifetime requirements. To address the SP-100 needs, a tribology development program has been established at GE to investigate candidate coating materials. Materials were selected based on their high thermodynamic stability, high melting point, compatibility with the substrate, and coefficients of thermal expansion similar to niobium-1% zirconium - the candidate structural material for SP-100. An additional requirement was that the deposition processes should be commercially available to coat large components.

If the labyrinth seal designer can first determine the nature, cause, and resolution of previous problems, he can then better judge what to do and how to do it for today's engines. The designer of long-life labyrinth seals is primarily interested in those design features and design criteria which have been substantiated by actual service experience. If the design features or criteria are too recent to have had significant service experience, component or factory engine tests may provide valuable substantiation.

Measurement of dimensional characteristics of airfoil parts is primarily a manual, labor intensive operation. It employs a wide variety of gages that vary from very expensive optical comparitors to inexpensive pin gages. An automatic non-contacting inspection gage capable of measuring most dimensional characteristics would be cost effective, simplify inspection operations, consolidate a number of gages into one, and improve overall inspection reliability by minimizing human involvement. This paper presents the results of the design and development of a demonstrator semi-automatic laser gage dimensional inspection system that addresses this problem.

The work reported in this paper has been conducted by a team from GE-Aircraft Engines, GE-CR&D, and Sundstrand under a contract sponsored by the USAF, Wright Laboratories, WPAFB, Contract No. F33615-90-C-2052. The objective of this contract is to prove the feasibility of an Integral Starter/Generator (IS/G) through the preliminary design stage and demonstrate the starter/ generator technology in the externally mounted version utilizing switched reluctance machine technology. This paper will report on the progress for the EIS/G-system through the initial testing stage. Comparison of the finished hardware with the design results presented earlier will lead of the paper. This is followed by the discussion of the early testing results for the system testing. Recommendation on additional testing will be presented at the end of the paper.

Previous studies had demonstrated the economic and technical feasibility of producing high-quality forgings for aircraft turbine engine parts from hot-isostatically pressed (HIP) Rene 95 powder billets. The present program was aimed at developing a production practice for making HIP + forged turbine discs. The major goal was improved product fabricability and reliability with minimum cost. The program was conducted using argon atomized Rene 95 powder. Experimental studies were conducted to evaluate the effect of powder characteristics, HIP parameters, preform design, and forging conditions on forgeability, microstructure, and mechanical properties. The results of these studies were incorporated into a pilot production run in which 10 disc forgings were made and evaluated. The selected process involved the consolidation of -60 mesh powder to full density by hot-isostatic pressing at a temperature above the γ' solvus temperature.

Initial preliminary development phases of two distinct SP-100 control drive assembly bearing test programs were successfully completed at elevated temperature in vacuum. The first was for the reflector drive line spherical self-aligning bearings. Each bearing consisted of a carbon-graphite ball mounted on an aluminum oxide-coated Ta-10%W shaft, captured by an aluminum oxide-coated Ta-10%W socket. One set of these bearings was exposed to temperatures up to 1180K (1665°F) at 1.33x10-6 Pa (1x10-8 torr) and subjected to 38000 cycles of motion. Friction coefficients were found to be between 0.11 and 0.25 over the full range of operation. Overall performance of the bearings was excellent, with only slight wear observed. The second test program was for the safety rod slider bearing. Zirconium carbide coated Nb-1%Zr bearing pads were stroked inside a molybdenum tube at temperatures up to 1422K (2100°F) at ∼1.33x10-6 Pa with a normal load of 1.02 Kg between each sliding surface.

This paper concerns a new technique designed to provide high performance reaction control systems for sounding rockets. Proportional control of differential thrust and simple adaptive control of thrust magnitude (based on the level of demanded thrust) is utilized. The control is being implemented with a combination of electronic and fluidic components for an Aerobee 150 sounding rocket payload whose goal is a pointing stability of 0.1 arc second.