Search Results

Resolving the brake squeal that occurs under various environments is a major topic, and a resolution method is eagerly anticipated. We focused on the phenomenon that, amid various environmental conditions, squeal occurs easily when an automobile has been left standing in a cold environment. We checked the details focusing on the friction coefficient (hereafter, μ). As a result, we found that μ increases when squeal is generated, and that the sliding surface film contributes to the μ behavior. We studied measures to be taken to increase the μ in cold conditions.

Brake noise problem is one of the most common customer complaints regarding brake systems. With a focus on low frequency squeal, we have studied the vibration modes of brake caliper. In the present study, we achieved the reduction of low frequency brake squeal through modal analysis of mounting brackets.

This paper describes the investigation into the contact pressure and incidental deformation on the contact surface of the piston skirt which comes in contact with the cylinder bore in operation. Focused on the single piston static tests in the first place, relationship between the contact pressure on said skirt and the strains developed inside the skirt, and the relationship between the deformation of skirt face and the strains inside the skirt were studied. Then, the dynamic contact pressure onto the skirt in operation and the amount of deformation were calculated based on the relationships mentioned above using the factor of dynamic strains measured on an engine in operation. The deformation of skirt calculated using said dynamic strains was verified by the direct measurement of the skirt deformation. It was demonstrated that the thrust side of a piston skirt was largely deformed due to enlarged contact pressure caused by the piston slap subsequent to firing top dead center.

We have developed Sensor-less Memory Seat system that requires no position sensors such as Hall ICs etc.. It detects the rotation of DC motor by current ripple signals in motor operating current. The developed Sensor-less position control system can attenuate a wide frequency variation of Motor current noise which varies depending on motor condition and convert small current ripples to Pulse signals in proportion to the rotation of DC motor. We realized low cost position control method for use in Memory Seat system.

This paper reports the results of a study into a preview control that uses the displacement of the road surface in front of the vehicle to improve for front and rear actuator responsiveness delays, as well as delays due to calculation, communication, and the like. This study also examined the effect of a preview control using the eActive3 electric active suspension system, which is capable of controlling the roll, pitch, and warp modes of vehicle motion.

Aiming at improved reliability and cost reduction of position sensors for automobiles, we tackled with the challenge of developing long life contact type potentiometer which has a simple construction and cost advantage. We made clear the wear characteristics of the resistor materials and the mechanism how noise occurs, and developed a long life, low noise resistor material, and the double - layer resistor structure which has excellent characteristic in durability. We also clarified the ways of using brushes according to applications through the investigation of the relationship between the contact shape and the amount of wear of the resistor. Based on these investigation, we have developed a highly reliable throttle position sensor and a long life vehicle height sensor.

In this paper, we discuss vehicle directional stability and introduce advanced stability control (ASTC) to stabilize the vehicle during severe cornering. Vehicle behavior in a transient steering condition during severe cornering was analyzed by computer simulation. It was found that applying an external yaw moment makes the vehicle more stable. The effect of controlling the brake force response is also evaluated by simulation to determine the brake actuator response criteria. The actual vehicle test was performed with a pylon slalom using a hydraulic brake actuator. It is verified that the ASTC stabilizes the vehicle for transient steering maneuvers.

When a clutch pedal is operated, the clutch pedal vibration and interior noise are mostly affected by the dynamic characteristics of the clutch cover assembly. We achieved a high correlation between vehicle test data and results using this method when exciting not only clutch system but also the engine system. Finally, we developed an excitation method to evaluate the dynamic characteristics of the clutch cover assembly.

As a part of our process engineering (planning) steps and in order to shorten the initial flow control after the implementation of a production system, we have been adopting countermeasures for defects that have been forecasted by the application of FMEA. However, due to this having to be done with limited information (which is dependent upon the skill level of the operator) and due to the fact that the effects of each particular countermeasure are not fully understood, we cannot be certain that the measures implemented during the planning stages are thorough enough. The current situation is that countermeasures for most issues are being handled during the initial flow control stages based on the trial-and-error method. Given this situation, normally, it would take us more than three months from the time of line-off (start of production) to achieve our target rate of capacity utilization.

It is well known that the self-aligning torque decreases before lateral force is saturated. Focusing on this self-aligning torque change, an estimation method has been developed to detect the friction condition between steered wheels and road surface before the lateral force reaches the friction limit. The lateral grip margin (LGM) is defined based on the self-aligning torque change, which is obtained using the EPS torque and motor current information. The LGM is theoretically analyzed based on the tire model and experimentally verified through the full-scale vehicle test. Moreover, the estimated LGM is applied for the chassis control systems to improve the vehicle dynamics performance.

Switched Reluctance Motor (SRM) mainly has two advantageous characteristics such as no magnet and simple construction. These characteristics contribute lower cost and higher reliability compared with other motor systems such as brushless permanent magnet motors or induction motors. However, SRM has disadvantages that are its torque ripple and acoustic noise in particularly. Moreover, the resonance frequency mode of a motor system is excited by torque ripple, and drive train vibration is caused. These noise and vibration should be suppressed when the SRM is applied to a traction system for passenger electric vehicle since these characteristics affect vehicle quietness and drivability. In this paper, we describe an approach to suppress drive train vibration and acoustic noise.

Responsiveness is one of the main characteristics of a brake booster. The design of a tandem booster, with its two boosting chambers, has a negative influence on high responsiveness. This report, using the CFD method for the air flow analysis, shows the way we found the most suitable air passage within the space of the given design of the current production tandem booster.

Automating the inspection of the piston combustion chamber volume is difficult and prevents establishing an unmanned machining process of the piston in the future. So, we developed an inspection technique which uses a Range Finder, non-contact visual sensor, and calculate the chamber volume by integrating 3D position data. We applied this real-time measurement technique which enables 100 % inspection to our production lines. Then, we developed the “Defect Free Production Line”, which calibrates itself by feeding back the measured volume data to the machining process. Our paper will explain this inspection technique and our “Defect Free Production Line”.

There are such outside door handles called smart handles which have a transmitting antenna, a lock/unlock sensor, and a sensor detection circuit, with which operation of door lock is possible just by "touching" the electrostatic-capacitance type sensor of the handles.As the design of the outside handles, body color painting and Cr plating are adopted. However, if plating is applied over the entire surface of a smart handle, electromagnetic waves transmitted from the antenna will be blocked since plating material is electrically conductive. In addition to this, touching a part other than the sensor may change the electrostatic-capacitance of the sensor, which results in unwanted functioning of the lock/unlock sensor. Because of this, only part of the handle, which does not hinder the transmission of electromagnetic waves and does not cause unwanted functioning, is covered by plating, that is called, "Partially plated specifications" (Figure 1).

Switched Reluctance Motor (SRM) mainly has two advantageous characteristics such as no magnet and simple construction. These characteristics contribute lower cost and higher reliability compared with other motor systems such as brushless permanent magnet motors or induction motors. However, acoustic noise and output torque ripple should be improved when the SRM is applied to a traction system for passenger electric vehicle since these characteristics directly affect vehicle quietness and drivability. In this paper, we describe a system configuration of the SRM traction system for passenger electric vehicle. The SRM traction system includes an electric motor, transmission gears and power inverter module. Then, an approach to improve acoustic noise and output torque ripple is introduced. Generation mechanisms of acoustic noise and output torque ripple are analyzed.

As a process that enables the high-speed and continuous forming of lengthy materials with a constant cross-sectional configuration, roll forming offers much higher productivity than the stamping process. However, in case a change must be made to the shape of the cross section, the material must normally be stamped or joined with a part containing a separate shape. This affects productivity, increases the number of pieces, and degrades the material's appearance. This report describes the roll-forming technology that we developed, in which the cross section of the material can be changed gradually. This method adopts a system which uses a movable and rotatable roll-stand that enables high-speed, continuous roll-forming processes.

One of the problems concerning T/M is conventionally how “Improving the input torque as the engine gets higher power” and “Making product lighter in weight and more compact to improve the fuel consumption” can be realized at the same time. To realize these things at the same time, it is needless to say that the gears must be stronger. For the “pitting fatigue strength” which is quoted as a problem lately, the fatigue mechanism has not been clarified, yet. Therefore, it is now a big problem how to achieve high strength. In the meantime, we tried to develop the production engineering for “finer crystal grains” and “fine-dispersion precipitation of carbo-nitrides,” and succeeded in improving “pitting fatigue strength” remarkably. Such results will be reported in the following sections: