Search Results

Yield potential was predicted and mapped for three corn fields in Central Illinois, using digital aerial color infrared images. Three methods, namely statistical (regression) modeling, genetic algorithm optimization and artificial neural networks, were used for developing yield models. Two image resolutions of 3 and 6 m/pixel were used for modeling. All the models were trained using July 31 image and tested using images from July 2 and August 31, all from 1998. Among the three models, artificial neural networks gave best performance, with a prediction error less than 30%. The statistical model resulted in prediction errors in the range of 23 to 54%. The lower resolution images resulted in better prediction accuracy compared to resolutions higher than or equal to the yield resolution. Images after pollination resulted in better accuracy compared to images before pollination.

Data obtained when harvesting with a combine equipped with a yield monitor were used to develop yield maps. A prototype yield monitor was developed that uses a combination of light emitters and receivers mounted in a rectangular frame. The monitor was mounted in the combine in the top of the clean grain elevator. As grain flows through the monitor, a voltage change proportional to light reduction was recorded. This voltage was then correlated to grain flow rate. At the same time, site-specific location was recorded using the global positioning satellites (GPS) system. The location data, yield monitor output, cutting width, and combine forward speed were stored in a spreadsheet format. The data were then used to prepare the yield maps.

With COSMOsim, OTSL is looking to better virtually recreate diverse driving conditions to enable safe and accurate verifications at a point when autonomous driving continues to move toward practical use around the world.

Knitted wiremesh along with radial gas tight seals provide reliable mounting system for low temperature underbody converters. The compression characteristics of the wiremesh is modified by wire material, wire diameter, wire geometry, mesh crimp heights; wire density, wiremesh courses per inch, needle count, number of strands, wiremesh temper, wiremesh surface profile and surface characteristics. The radial mounting pressure provided by the wiremesh is matched with the mounting pressure requirement. Wiremesh systems can be tailored to any required radial mounting pressure from conventional to ultra thin-wall substrates. The wiremesh mounting system is proven durable, without any failure on more than 25 million underbody converters in light duty vehicles. Cp and Cpk show the capability of the manufacturing process. Thus the wiremesh mounting support is a viable alternate for low temperature gasoline and diesel applications.

Through this work, Wind River and Airbiquity look to enable secure and intelligent software updates and data management for these vehicles through over-the-air (OTA) programming technology. The work may also lead to similar solutions for traditional aerospace and unmanned aircraft system (UAS) industries.

This SAE Recommended Practice establishes uniform engineering nomenclature for wide base disc wheels and demountable rims. This nomenclature and accompanying figures are intended to define fundamental wide base disc wheel and demountable rim terms. The dimensions given are those necessary to maintain serviceability and interchangeability of the wide base disc wheels and demountable rims with standard hardware. Valve clearances have not been included in this document.

This SAE Recommended Practice establishes uniform engineering nomenclature for wide base disc wheels and demountable rims. This nomenclature and accompanying figures are intended to define fundamental wide base disc wheel and demountable rim terms. The dimensions given are those necessary to maintain serviceability and interchangeability of the wide base disc wheels and demountable rims with standard hardware. Valve clearances have not been included in this document.

This SAE Recommended Practice establishes uniform engineering nomenclature for wide base disc wheels and demountable rims. This nomenclature and accompanying figures are intended to define fundamental wide base disc wheels and demountable rim terms. The dimensions given are those necessary to maintain serviceability and interchangeability of the wide base disc wheels and demountable rims with standard hardware. Valve clearances have not been included in this document.

HIGH output per cubic inch of piston displacement is desirable not alone for the purpose of being able to transport more payload faster, but more particularly for the invariably associated byproduct of lower specific fuel consumption, and especially at road-load requirements. The only way of accomplishing this purpose is through the use of higher compression ratios, and the limiting factors for this objective are fuel distribution and the operating temperatures of the component parts. A manifold is proposed which not only definitely improves distribution at both full and road loads, but has the inherent additional advantage of reducing the formation of condensate, thus still further facilitating a reduction in road-load specific fuel consumption. Hydraulic valve lifters, obviation of mechanical and thermal distortion, and controlled water flow are the essentials in improved cooling.

The pressures created by the work environment and its demands can be many and varied. The effect of these pressures and demands can be extremely taxing to essentially every facet of the person experiencing them. However, this stress can be effectively managed and even prevented by using the appropriate measures.

This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of wheels and demountable rims intended for normal highway use on trucks, buses, truck-trailers, and multipurpose vehicles. For other wheels intended for normal highway use and temporary use on passenger cars, light trucks, and multipurpose vehicles, see SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, see SAE J1204. For bolt together military wheels, see SAE J1992. This document does not cover other special application wheels and rims.

This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of wheels and demountable rims intended for normal highway use on trucks, buses, truck-trailers, and multipurpose vehicles. For other wheels intended for normal highway use and temporary use on passenger cars, light trucks, and multipurpose vehicles, see SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, see SAE J1204. For bolt together military wheels, see SAE J1992. This document does not cover other special application wheels and rims.

This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of disc wheels, demountable rims, and bolt-together wheels intended for normal highway use on military trucks, buses, truck-trailers, and multipurpose vehicles. For wheels and rims intended for normal highway use by trucks, see SAE J267. For wheels intended for normal highway use by passenger cars, light trucks, and multipurpose vehicles, see SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, see SAE J1204. This document does not cover off-highway or other special application wheels and rims.

This SAE Recommended Practice provides minimum performance target and uniform laboratory procedures for fatigue testing of wheels and demountable rims intended for normal highway use on trucks, buses, truck-trailers, and multipurpose vehicles. Users may establish design criteria exceeding the minimum performance target for added confidence in a design. The cycle target noted in Tables 1 and 2 are based on Weibull statistics using two parameter, median ranks, 50% confidence level and 90% reliability, and beta equal to two, typically noted as B10C50. For other wheels intended for normal highway use and temporary use on passenger cars, light trucks, and multipurpose vehicles, refer to SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, refer to SAE J1204. For bolt together military wheels, refer to SAE J1992. This document does not cover other special application wheels and rims.

This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of wheels and demountable rims intended for normal highway use on trucks, buses, truck-trailers, and multipurpose vehicles. Users may establish design criteria exceeding the minimum performance requirement for added confidence in a design. The cycle requirements noted in Tables 1 and 2 are based on Weibull statistics using 2 parameter, median ranks, 50% confidence level and 90% reliability, and beta equal to 2, typically noted as B10C50. For other wheels intended for normal highway use and temporary use on passenger cars, light trucks, and multipurpose vehicles, see SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, see SAE J1204. For bolt together military wheels, see SAE J1992. This document does not cover other special application wheels and rims.

This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of disc wheels, demountable rims, and bolt-together divided wheels intended for normal highway use on military trucks, buses, truck-trailers, and multipurpose vehicles. Users may establish design criteria exceeding the minimum performance requirement for added confidence in a design. For other (non-military) wheels and rims intended for normal highway use on trucks and buses, refer to SAE J267. For wheels intended for normal highway and temporary use on passenger cars, light trucks, and multipurpose vehicles, refer to SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, refer to SAE J1204. This document does not cover off-highway or other special application wheels and rims.

While the basis of wheel design has evolved by using current technological materials and concepts, the manufacturing and design is still inexact and partially an art. This paper reviews wheels intended for use on commercial vehicles, including light, medium, and heavy trucks, truck trailers, transit, and inter-city buses. The paper also covers spoke-type wheels, demountable rims, and disc-type wheels with rims from 13 inch diameter to 24 inch diameter. The paper encompasses a brief history, historical and market trends by vehicular types, design parameters, standardization, industrial technical committees, and future trends in design and materials.

The SAE Recommended Practice establishes minimum performance requirements and related uniform laboratory test procedures for evaluating lateral (curb) impact collision resistance of all wheels intended for use on passenger cars and light trucks.

The paper attempts to determine which traction model best fits with experimental data for a romanian lugged tractor tire. Different models for predicting net traction and traction efficiency for off-road conditions were considered. These models assume different tire-ground pressure distributions (constant, parabolic) over the undertread area and different contact patch length calculations. Experiments were conducted and the results were compared to the theoretical data. Two of the models are the best fit with the experimental data; both models assumed a parabolic pressure distribution over the undertread.

The wheel motor is a combination of hydro-motor and planetary transmission. Industrial, agricultural, construction and various types of public utility vehicles, which due to their design cannot use axle drives, make increasing use of the individual wheel drive. Speed, torque transmission, wheel bearings, valves for hydraulic operation and hydraulic engagement/disengagement are some of the requirements for wheel motor drives.