Search Results

In the modern and fast growing automotive sector, reliability & durability are two terms of utmost importance along with weight & cost optimization. Therefore it is important to explore new technology which has less weight, low manufacturing cost and better strength. The new technology developed always seek for a quick, cost effective and reliable methodology for its design validation so that any modification can be made by identifying the failures. This paper presents the rig level test methodology to validate and to correlate the CAE derived strain levels, life cycle & failure mode of newly developed light weight stabilizer link for EV Bus suspension

Yield potential was predicted and mapped for three corn fields in Central Illinois, using digital aerial color infrared images. Three methods, namely statistical (regression) modeling, genetic algorithm optimization and artificial neural networks, were used for developing yield models. Two image resolutions of 3 and 6 m/pixel were used for modeling. All the models were trained using July 31 image and tested using images from July 2 and August 31, all from 1998. Among the three models, artificial neural networks gave best performance, with a prediction error less than 30%. The statistical model resulted in prediction errors in the range of 23 to 54%. The lower resolution images resulted in better prediction accuracy compared to resolutions higher than or equal to the yield resolution. Images after pollination resulted in better accuracy compared to images before pollination.

Data obtained when harvesting with a combine equipped with a yield monitor were used to develop yield maps. A prototype yield monitor was developed that uses a combination of light emitters and receivers mounted in a rectangular frame. The monitor was mounted in the combine in the top of the clean grain elevator. As grain flows through the monitor, a voltage change proportional to light reduction was recorded. This voltage was then correlated to grain flow rate. At the same time, site-specific location was recorded using the global positioning satellites (GPS) system. The location data, yield monitor output, cutting width, and combine forward speed were stored in a spreadsheet format. The data were then used to prepare the yield maps.

With COSMOsim, OTSL is looking to better virtually recreate diverse driving conditions to enable safe and accurate verifications at a point when autonomous driving continues to move toward practical use around the world.

Knitted wiremesh along with radial gas tight seals provide reliable mounting system for low temperature underbody converters. The compression characteristics of the wiremesh is modified by wire material, wire diameter, wire geometry, mesh crimp heights; wire density, wiremesh courses per inch, needle count, number of strands, wiremesh temper, wiremesh surface profile and surface characteristics. The radial mounting pressure provided by the wiremesh is matched with the mounting pressure requirement. Wiremesh systems can be tailored to any required radial mounting pressure from conventional to ultra thin-wall substrates. The wiremesh mounting system is proven durable, without any failure on more than 25 million underbody converters in light duty vehicles. Cp and Cpk show the capability of the manufacturing process. Thus the wiremesh mounting support is a viable alternate for low temperature gasoline and diesel applications.

Through this work, Wind River and Airbiquity look to enable secure and intelligent software updates and data management for these vehicles through over-the-air (OTA) programming technology. The work may also lead to similar solutions for traditional aerospace and unmanned aircraft system (UAS) industries.

HIGH output per cubic inch of piston displacement is desirable not alone for the purpose of being able to transport more payload faster, but more particularly for the invariably associated byproduct of lower specific fuel consumption, and especially at road-load requirements. The only way of accomplishing this purpose is through the use of higher compression ratios, and the limiting factors for this objective are fuel distribution and the operating temperatures of the component parts. A manifold is proposed which not only definitely improves distribution at both full and road loads, but has the inherent additional advantage of reducing the formation of condensate, thus still further facilitating a reduction in road-load specific fuel consumption. Hydraulic valve lifters, obviation of mechanical and thermal distortion, and controlled water flow are the essentials in improved cooling.

Meet like-minded mobility engineersto discuss new legislation and regulations around thermal management, emissions control, safety, and energy conservation.

Meet like-minded mobility engineersto discuss new legislation and regulations around thermal management, emissions control, safety, and energy conservation.

Why should you attend the 2022 Thermal Management Systems Symposium

Statistical measures of whole-body vibration from ambulation are shown to be higher than those from operation of earthmoving machinery and significantly higher than published guidelines for human exposure to whole-body vibration. The inconsistency of human response to low level vibration of technological origin as compared to human imperceptiveness to high level vibration from ambulation is discussed.

The pressures created by the work environment and its demands can be many and varied. The effect of these pressures and demands can be extremely taxing to essentially every facet of the person experiencing them. However, this stress can be effectively managed and even prevented by using the appropriate measures.

The SAE Recommended Practice establishes minimum performance requirements and related uniform laboratory test procedures for evaluating lateral (curb) impact collision resistance of all wheels intended for use on passenger cars and light trucks.

The paper attempts to determine which traction model best fits with experimental data for a romanian lugged tractor tire. Different models for predicting net traction and traction efficiency for off-road conditions were considered. These models assume different tire-ground pressure distributions (constant, parabolic) over the undertread area and different contact patch length calculations. Experiments were conducted and the results were compared to the theoretical data. Two of the models are the best fit with the experimental data; both models assumed a parabolic pressure distribution over the undertread.

This SAE standard presents the basic information required for the design and manufacture of a wheel chock.

Abstract Wheel chocks are rather simple compliant mechanisms for stabilizing vehicles at rest. However, chocks must be carefully designed given the complex interaction between the chock and the tire/suspension system. Despite their importance for safety, literature is surprisingly limited in terms of what makes a wheel chock efficient. Using simple but reliable quasi-static mechanical models, this study identifies mechanical requirements that help to avoid a number of failure modes associated with many existing wheel chocks. Given that chock grounding is not always possible, a chock’s maximum restraining capacity is only obtained when the wheel is completely supported by the chock. A generic chock profile is proposed to achieve this objective while mitigating undesirable failure modes. The profile is based on fundamental mechanical principles and no assumption is made on the load interaction between the chock and the wheel.

This paper describes how the needs of the truck end-user have changed under the pressures of deregulation and competition, and how the truck supply community has responded. It observes that traditional management and hardware responses are yielding diminishing improvements. Significant further improvement is postulated based on application of electronic technology to functional control of a “truck system”. This is defined as a technological discontinuity where a new perspective, “thinking systems” will be needed. The post-1995 truck system is described; and what “thinking systems” entails and “how to create a system” are discussed. It is further postulated that this change in technology will have major impacts on the structure of the truck manufacturing industry, and the capabilities required of its management and technical communities.

Quality improvement, widely accepted as the key to survival in today's global marketplace, can only be achieved through a disciplined approach to problem solving based on proven statistical process control (SPC) techniques. Improving quality also improves productivity, and SPC applications are generating substantial savings for both product and service organizations throughout industry.

The scope of Finite Element Analysis in the Product Development Cycle is given. A brief review of the development process is given. A brief description of the analysis method is presented. A description of how it works, how is it implemented, and where do I use it are included. The entire range of questions are answered through, how do I train for it, how do I manage it, along with what are the limitations and what are the benefits of this analysis method.

Formulas are derived to show that moving elements of a drive train can contribute to the energy seen by the clutch plates. Oscillograph traces, sample calculations and photographs of failed plates show actual energy at failure of test plates. The formula is presented for calculating instantaneous energy when coefficient of friction, apply pressure and slip speed are known or can be estimated.