Search Results

Powertrain electrification is becoming increasingly common in the transportation sector to address the challenges of global warming and deteriorating air quality. This paper introduces a novel “Build Your Hybrid” approach to experience and test various hybrid powertrain concepts. This approach is applied to the light commercial vehicles (LCV) segment due to the attractive combination of a Diesel engine and a partly electrified powertrain. For this purpose, a demonstrator vehicle has been set up with a flexible P02 hybrid topology and a prototype Hybrid Control Unit (HCU). Based on user input, the HCU software modifies the control functions and simulation models to emulate different sub-topologies and levels of hybridization in the demonstrator vehicle. Three powertrain concepts are considered for LCVs: HV P2, 48V P2 and 48V P0 hybrid. Dedicated hybrid control strategies are developed to take full advantage of the synergies of the electrical system and reduce CO2 and NOx emissions.

Yield potential was predicted and mapped for three corn fields in Central Illinois, using digital aerial color infrared images. Three methods, namely statistical (regression) modeling, genetic algorithm optimization and artificial neural networks, were used for developing yield models. Two image resolutions of 3 and 6 m/pixel were used for modeling. All the models were trained using July 31 image and tested using images from July 2 and August 31, all from 1998. Among the three models, artificial neural networks gave best performance, with a prediction error less than 30%. The statistical model resulted in prediction errors in the range of 23 to 54%. The lower resolution images resulted in better prediction accuracy compared to resolutions higher than or equal to the yield resolution. Images after pollination resulted in better accuracy compared to images before pollination.

Data obtained when harvesting with a combine equipped with a yield monitor were used to develop yield maps. A prototype yield monitor was developed that uses a combination of light emitters and receivers mounted in a rectangular frame. The monitor was mounted in the combine in the top of the clean grain elevator. As grain flows through the monitor, a voltage change proportional to light reduction was recorded. This voltage was then correlated to grain flow rate. At the same time, site-specific location was recorded using the global positioning satellites (GPS) system. The location data, yield monitor output, cutting width, and combine forward speed were stored in a spreadsheet format. The data were then used to prepare the yield maps.

With COSMOsim, OTSL is looking to better virtually recreate diverse driving conditions to enable safe and accurate verifications at a point when autonomous driving continues to move toward practical use around the world.

This SAE Recommended Practice establishes uniform test procedures and performance requirements for the defrosting system of enclosed cab trucks, buses, and multipurpose vehicles. It is limited to a test that can be conducted on uniform test equipment in commercially available laboratory facilities. Current engineering practice prescribes that for laboratory evaluation of defroster systems, an ice coating of known thickness be applied to the windshield and left- and right-hand side windows to provide more uniform and repeatable test results, even though under actual conditions such a coating would necessarily be scraped off before driving. The test condition, therefore, represents a more severe condition than the actual condition, where the defroster system must merely be capable of maintaining a cleared viewing area.

Through this work, Wind River and Airbiquity look to enable secure and intelligent software updates and data management for these vehicles through over-the-air (OTA) programming technology. The work may also lead to similar solutions for traditional aerospace and unmanned aircraft system (UAS) industries.

Cast iron is generally thought of as a weak, dirty, cheap, brittle material that does not have a place in applications requiring high strength and defined engineering properties. While gray cast iron is relatively brittle by comparison with steel, ductile iron is not. In fact, ductile iron has strengths and toughness very similar to steel and the machinability advantages make an attractive opportunity for significant cost reductions. Gray and ductile iron bar stock is commercially available and can be used as a direct replacement in applications that are currently being made from carbon steel bar. Ductile iron bar stock conversions are very prevalent in many fluid power applications including glands and rod guides, cylinders, hydrostatic transmission barrels and in high-pressure manifolds. Automotive gears are being converted to ductile iron for its damping capacity and cost reductions.

HIGH output per cubic inch of piston displacement is desirable not alone for the purpose of being able to transport more payload faster, but more particularly for the invariably associated byproduct of lower specific fuel consumption, and especially at road-load requirements. The only way of accomplishing this purpose is through the use of higher compression ratios, and the limiting factors for this objective are fuel distribution and the operating temperatures of the component parts. A manifold is proposed which not only definitely improves distribution at both full and road loads, but has the inherent additional advantage of reducing the formation of condensate, thus still further facilitating a reduction in road-load specific fuel consumption. Hydraulic valve lifters, obviation of mechanical and thermal distortion, and controlled water flow are the essentials in improved cooling.

This SAE standard presents the basic information required for the design and manufacture of a wheel chock.

The EU Commission's “Clean Power for Transport” initiative aims to break the EU's dependence on imported oil whilst promoting the use of alternative fuels to reduce greenhouse gas emissions. Among the options considered is the use of liquefied natural gas (LNG) as a substitute for diesel in long haul trucks. It is interesting to ask how the lifecycle greenhouse gas (GHG) emissions of LNG compare with conventional diesel fuel for this application. The LNG available in Europe is mainly imported. This paper considers the “well-to-tank” emissions of LNG from various production routes, including: gas production, treatment and liquefaction, shipping to Europe, terminal, distribution and refuelling operations. “Tank-to-Wheel” emissions are considered for a range of currently-available engine technologies of varying efficiency relative to diesel.

The environmental impact from herbicide utilization has been well documented in recent years. The reduction in weed control with out a viable alternative will likely result in decreased per acre production and thus higher unit production cost. The potential for selective herbicide application to reduce herbicide usage and yet maintain adequate weed control has generated significant interest in different forms of remote sensing of agricultural crops. This research evaluated the color co-occurrence texture analysis technique to determine its potential for utilization in crop groundcover identification. A program termed GCVIS (Ground Cover VISion) was developed to control an ATT TARGA 24 frame grabber; and generate HSI color features from the RGB format pixel data, HSI CCM matrices and the co-occurrence texture feature data.

Wear characteristics of four bearing materials have been investigated under different sliding conditions. The bearing materials used were CDA 954, CDA 863, CDA 932, and CDA 938. Using a Taber Wear Tester, a cylinder on a flat geometry was used as a tribo contact pair. All bearing materials in the form of a thick cylindrical disk were subjected to combined sliding-rolling motion against a rotating flat disk. The flat disk was either an abrasive disk, or a very soft steel disk, or a hardened steel disk with and without lubrication. Wear was measured as weight loss after several thousand cycles of rotation. Maximum wear of the bearing materials occurred when the counter body was a very soft steel disk. These results together with the wear rate of each bearing material sliding against four different counter bodies are presented. These results are found to be of practical importance in the design and application of journal bearings made of materials used in this investigation.

Axial piston type pumps are often exposed to severe operating conditions because of the duty cycle, the environment, or, in some situations, poor maintenance and even abuse. The detrimental effects on the pump and the hydraulic system as a result of these adverse conditions are often not known or predictable. In this study, four controlled severe operating conditions were imposed on four identical axial piston type pumps. They included 1) constant high load pressure and normal fluid temperature, 2) constant high load pressure and elevated fluid temperature, 3) cyclic load pressure and normal fluid temperature, and 4) cyclic load pressure and elevated fluid temperature. The tests were long-term; they were run continuously for up to 5000 hours. The pump wear was monitored in all cases using ferrography. In addition, the condition of the fluid was monitored and the circuit filters were examined periodically. The results of the findings are presented in this paper.

This paper is concerned with the synergistic effects of pump wear modes. The objective is to investigate the wear produced by cavitation, adhesion, abrasion, and corrosion and to verify a proposed model of the synergistic pump wear process. The approach followed includes identification of the combined effects of different wear modes (synergisms) in a pump and the development of a synergistic wear model that includes pump operating and environmental conditions as trigger factors of wear modes. An experimental program was designed to evaluate the cavitation, adhesion, and corrosion wear effects in conjunction with the abrasive wear produced in a pump by measuring wear debris, particle size and gravimetric levels of fluid. The generation of wear was traced to different pump locations. The results obtained here suggest that improved pump design and longer pump service life can be obtained when synergisms between failure modes are properly understood.

Hydraulic fluid performance, including water-glycols (W/G), is dependent on the chemical composition of the fluid and cleanliness. An overview of W/G fluid chemistry on pump wear is provided here. Also provided, is a brief overview of the impact of fluid cleanliness on the potential wear properties of various components. Finally, an overview of recommended analytical procedures to assure adequate long-term fluid hydraulic and lubrication performance is provided. If these procedures are followed, substantial improvements in hydraulic pump longevity and performance will be realized.

One of the most commonly used tests to evaluate the antiwear properties of a hydraulic fluid is ASTM D 2882 which is based on a Vicker's V-104 vane pump. Although this is a commonly used test, the results are subject to numerous potential problems in both testing procedure and pump hardware. In this paper, the particular focus will be placed on potential problems that may be encountered with testing of water-glycol hydraulic fluids which may lead to erroneous and non-reproducible results.

Few previous publications investigate the possibility of combining multiple waste heat sources in a combustion engine waste heat recovery system. A waste heat recovery system for a HD truck diesel engine is evaluated for utilizing multiple heat sources found in a conventional HD diesel engine. In this type of engine more than 50% of heat energy goes futile. The majority of the heat energy is lost through engine exhaust and cooling devices such as EGRC (Exhaust gas recirculation cooler), CAC (Charge air cooler) and engine cooling. In this paper, the potential of usable heat recuperation from these devices using thermodynamic analysis was studied, and also an effort is made to recuperate most of the available heat energy that would otherwise be lost. A well-known way of recuperating this heat energy is by employing a Rankine cycle circuit with these devices as heat sources (single loop or dual loop), and thus this study is focused on using a Rankine cycle for the heat recovery system.

The use of reciprocating internal combustion engines (ICE) dominates the sector of the in-the-road transportation sector, both for light and heavy duties. CO2 reduction is the technological driver, considering the severe worldwide greenhouse commitments. In ICE more than one third of the fuel energy used is rejected to the environment as thermal waste through the exhaust gases. Therefore, a greater fuel economy could be achieved, recovering this energy and converting it into useful electric power on board. Financial benefits will be produced in terms of fuel cost which will rebound similar benefits in terms of CO2 emitted. For long hauling vehicles, which run for thousands of miles, frequently at fixed engine operating conditions, this recovery appears very worthy of attention. In this activity, an ORC-based power unit was designed, built and tested fed by a heavy duty diesel engine, so contributing to the huge efforts on going in that specific sector.

The China Automotive Technology and Research Center Co., Ltd. (CATARC), TÜV SÜD Group, and Shanghai SH Intelligent Automotive and International Transportation Innovation Center (ITIC) have joined with SAE International to establish the International Alliance for Mobility Testing and Standardization (IAMTS).