Search Results

A program was developed that provides a user friendly interface for developing and testing shift tables in a powershift transmission. This program is Windows based and runs on an IBM compatible P.C. When coupled with a suitable controller, transmission designers have a useful tool for the development of transmission shift timing. The system is designed to be used in an engine test cell or for actual vehicle tests. This allows the vehicle operator to call up and edit shifts on a P.C. screen and then drive the vehicle using the new shifts. This allows the operator to evaluate results of real time shifts immediately.

SIX BASIC suggestions are offered on how to design for practical, producible, economical structures of brazed honeycomb sandwich. The author illustrates the application of some of these design suggestions and explores the step-by-step theoretical reasoning a designer might use to arrive at a satisfactory design for a hypothetical large missile wing. The final design of a honeycomb sandwich component must take into account the process as well as structural and configuration requirements.

ZF debuts ADAS deal and flexible inverter tech at CES 2022

Join other young professionals in the mobility industry at the COMVEC™ meeting.

Instantaneous combine grain yield monitors need to provide reliable yield measurements since yield as a function of location is key information needed to manage fields by management zones. A scale and a yield monitor measured the same stream of grain and provided similar results when compared to each other. Data from either device may be misinterpreted if care in calibration and operation is not taken. Careful operators who pay attention to calibration, maintenance, and manufacturer's instructions will be required.

Data obtained when harvesting with a combine equipped with a yield monitor were used to develop yield maps. A prototype yield monitor was developed that uses a combination of light emitters and receivers mounted in a rectangular frame. The monitor was mounted in the combine in the top of the clean grain elevator. As grain flows through the monitor, a voltage change proportional to light reduction was recorded. This voltage was then correlated to grain flow rate. At the same time, site-specific location was recorded using the global positioning satellites (GPS) system. The location data, yield monitor output, cutting width, and combine forward speed were stored in a spreadsheet format. The data were then used to prepare the yield maps.

It is the goal of this paper, to discuss the impact of electronics on modern day commercial vehicles an buses. Seen from the position of advanced engineering of an European commercial vehicle manufacturer, the emphasis will be placed on the mechanical-electronical system itself, rather than the electronics themselves. User friendly, logic protected systems will minimize operator unfamiliarity and misapplication and will offer not only component control, but shortly the integration of all of these subsystems in the total vehicle control. Total vehicle control will be the ultimate result, when the driver, the truck and the environment are brought together. Such vehicles will be more responsive, safer and easier to drive than today's commercial vehicles and buses and offer a cost effective utilization of these new technologies to the customer.

The quality and availability of distillate fuels in the coming decades has become an increasing concern to the U.S. Navy. In response, the Energy Research and Development Office of the David Taylor Naval Ship Research and Development Center (DTNSRDC) has conducted a worldwide survey of commercial marine fuels. An effort was made to obtain 50 commercial marine fuel samples from various suppliers worldwide. The purpose of the survey was to assess the current quality of available fuels by analytically characterizing each of the fuel samples obtained. This assessment consisted of the measurement of more than 44 fuel properties. This paper contains a summary of the analytical results which were obtained. In addition, the current analytical results are compared with refinery specifications, with the current Navy specification, and with the results of a similar survey conducted in 1983. Finally, the resulting conclusions and recommendations are presented.

United States construction equipment manufacturers are subject to a maze of product-oriented regulations in marketing their U.S.-built products in foreign countries. These same obstacles face their foreign-built products. In the past, these foreign regulations were more apt to be trade barriers to protect domestic markets than bonafide regulations to protect the users. These trade barriers are gradually being lifted because manufacturers in virtually all countries have now expanded beyond their domestic markets. Thus, the same manufacturers that formerly encouraged trade barriers must now cope with them. This expansion of markets now encourages the elimination of trade barriers and the harmonization of regulations. For the future, regulations will be retained and expanded. They will, however, be harmonized with international voluntary standards rather than having different regulations for each country.

The idea of a world truck is a fascinating challenge - whereas cars are purchased more or less as seen; truck purchasers demand more individual configurations. In national and global terms, that means a highly complex truck market. Historically, a few European and North American manufacturers produced almost all the trucks for the world market. That changed through the 60's and 70's, with more local assembly plants around the world and increasing worldwide manufacturing capabilities. Concurrently, international component design standards have made some progress towards compatibility. Much greater co-operation is needed, however, before a genuinely international set of standards can be applied. As the task assigned to trucks is the same worldwide, namely to transport goods from A to B; it should be desirable and possible to work towards a greater commonality of vehicle - to ultimately achieve a world truck. The only unknown is the time scale.

Standardization and “Zero-Defects” are buzz-words among today's truck manufacturers. Electrical components is an area where these words must become reality. Components costing less than 1% of the final truck price should not cause problems for the end user or the manufacturer. The way to insure this is communication and design. Design out problems with new components.

Work solenoids are widely used in household appliances. The environment and design of this type application does not lead to solenoids for the earthmoving industry. This paper presents the environmental effects to be considered when designing a solenoid for the earthmoving industry. It further explains the need for, and type of, test necessary to validate the design. Finally a review of production quality procedures, necessary to insure reliable production parts is discussed.

An anchor product for T/CCI Manufacturing, the 7H wobble plate compressor is claimed to be the leading design in the industry for the heavy-duty truck and construction sector.

This SAE Standard specifies requirements and design guidelines for electrical wiring systems of less than 50 V and cable diameters from 0.8 to 19 mm2 used on off-road, self-propelled earthmoving machines as defined in SAE J1116 and agricultural tractors as defined in ASAE S390.

This SAE Standard specifies requirements and design guidelines for electrical wiring systems of less than 50 V and cable diameters from 0.35 to 19 mm2 used on off-road, self-propelled earthmoving machines as defined in SAE J1116 and agricultural tractors as defined in ASAE S390.

This SAE Standard specifies requirements and design guidelines for electrical wiring systems of less than 50 V and cable diameters from 0.35 to 19 mm2 used on off-road, self-propelled earthmoving machines as defined in SAE J1116 and agricultural tractors as defined in ASAE S390.

This SAE Standard specifies requirements and design guidelines for electrical wiring systems of less than 50 V and cable diameters from 0.8 to 19 mm2 used on construction, agricultural, and general purpose industrial categories of off-road self-propelled work machines as defined in SAE J1116.

This SAE Standard specifies requirements and design guidelines for electrical wiring systems of less than 50 V and cable diameters from 0.8 to 19 mm2 used on construction, agricultural, and general purpose industrial categories of off-road self-propelled work machines as defined in SAE J1116.

Knitted wiremesh along with radial gas tight seals provide reliable mounting system for low temperature underbody converters. The compression characteristics of the wiremesh is modified by wire material, wire diameter, wire geometry, mesh crimp heights; wire density, wiremesh courses per inch, needle count, number of strands, wiremesh temper, wiremesh surface profile and surface characteristics. The radial mounting pressure provided by the wiremesh is matched with the mounting pressure requirement. Wiremesh systems can be tailored to any required radial mounting pressure from conventional to ultra thin-wall substrates. The wiremesh mounting system is proven durable, without any failure on more than 25 million underbody converters in light duty vehicles. Cp and Cpk show the capability of the manufacturing process. Thus the wiremesh mounting support is a viable alternate for low temperature gasoline and diesel applications.

This SAE Recommended Practice establishes for trucks, buses, and multipurpose passenger vehicles with GVW of 4500 kg (10 000 lb) or greater: a Minimum performance requirements for windshield wiping systems. b Uniform test procedures that include those tests that can be conducted on uniform test equipment by commercially available laboratory facilities. c Uniform terminology of windshield wiper system characteristics and phenomena consistent with those found in guides for the use of engineering layout studies to evaluate system performance. d Guides for the design and location of components of the systems for function, servicing of the system, etc. The test procedures and minimum performance requirements, outlined in this document, are based on currently available engineering data. It is the intent that all portions of the document will be periodically reviewed and revised as additional data regarding windshield wiping system performance are developed.