Search Results

When evaluating the wear properties of slide bearings for car engines, it is a common practice to conduct long-term physical test using a bearing tester for screening purposes according to the revolution speed of the shaft, supply oil temperature and bearing pressure experienced in the actual use of engines. The loading waveform applied depends on the capability of the tester that is loaded, and it is often difficult to apply a loading waveform equivalent to that of actual engines. To design an engine that is more compact or lighter, it is necessary to reduce the dimensions of slide bearings and the distance between bearings. This requires loading tests on a newly designed engine by applying a loading waveform equivalent to that of actual engines to slide bearings and their vicinity before conducting a firing test. We therefore conducted an engine firing test by attaching thin-film sensors to the slide bearing part of the engine and measured the actual load distribution.

For various densities of gas jets including very light hydrogen and relatively heavy ones, the penetration length and diffusion process of a single high-speed gas fuel jet injected into air are computed by performing a large eddy simulation (LES) with fewer arbitrary constants applied for the unsteady three-dimensional compressible Navier-Stokes equation. In contrast, traditional ensemble models such as the Reynolds-averaged Navier-Stokes (RANS) equation have several arbitrary constants for fitting purposes. The cubic-interpolated pseudo-particle (CIP) method is employed for discretizing the nonlinear terms. Computations of single-component nitrogen and hydrogen jets were done under initial conditions of a fuel tank pressure of gas fuel = 10 MPa and back pressure of air = 3.5 MPa, i.e., the pressure level inside the combustion chamber after piston compression in the engine.

This study examined a method of predicting the piston temperature in reciprocating internal combustion engines with the aim of developing lightweight pistons. Since the piston temperature is strongly affected by the in-cylinder temperature distribution and turbulence, it is necessary to consider the effects of flame propagation, cooling by the intake air, temperature rise due to combustion, in-cylinder flow and the combustion chamber shape. A three-dimensional combustion simulation that can take these effects into consideration was run to calculate the heat transfer coefficient from the piston crown surface and the gas temperature. The results were used as the boundary conditions for an analysis of heat transfer from the piston, and a method was thus developed for analyzing the piston temperature.

The concept of the Early or late Intake valve closing cycle has been examined over the years as a technique for improving fuel economy in conjunction with the use of a three-way catalyst for excellent exhaust emission performance. With this concept, the intake valve closing (IVC) timing is set either before or after bottom dead center. With the emergence of continuously variable valve timing and lift (VEL) systems in recent years, the Early IVC cycle has become a more familiar concept. However, the Early IVC cycle has an intrinsic drawback in that, although pumping losses decrease when charging efficiency is reduced in connection with IVC control, combustion performance deteriorates due to the decline in the effective compression ratio. In recent years, full-scale research has been undertaken on variable compression ratio systems as a new type of variable engine mechanism separate from variable valving.

As technologies for simultaneously maintaining the current high thermal efficiency of diesel engines and reducing particulate matter (PM) and nitrogen oxide (NOX) emissions, many new combustion concepts have been proposed, including premixed charge compression ignition (PCCI) and low-temperature combustion[1]. However, it is well known that since such new combustion techniques precisely control combustion temperatures and local air-fuel ratios by varying the amount of air, the exhaust gas recirculation (EGR) ratio and the fuel injection timing, they have the issues of being less stable than conventional combustion techniques and of performance that is subject to variance in the fuel and driving conditions. This study concerns a system that addresses these issues by detecting the ignition timing with in-cylinder pressure sensors and by controlling the fuel injection timing and the amount of EGR for optimum combustion onboard.

There has been strong public demand for reduced hazardous exhaust gas emissions and improved fuel economy for automobile engines. In recent years, a number of innovative solutions that lead to a reduction in fuel consumption rate have been developed, including in-cylinder direct injection and lean burn combustion technologies, as well as an engine utilizing a large volume of exhaust gas recirculation (EGR). Furthermore, a homogeneous charge compression ignition (HCCI) engine is under development for actual application. However, one of the issues common to these technologies is less stable combustion, which causes difficulty in engine management. Additionally, it is now mandatory to provide an onboard diagnosis (OBD) system. This requires manufacturers to develop a technology that allows onboard monitoring and control of the combustion state. This paper reports on an innovative combustion diagnostic method using an in-cylinder pressure sensor.

We developed a technique to measure oil film pressure distribution in engine main bearings using thin-film pressure sensors. The sensor is 7μm in thickness, and is processed on the surface of an aluminum alloy bearing. In order to increase the durability of the sensor, a layer of MoS2 and polyamide-imide was coated on thin-film sensors. This technique was applied to a 1.4L common-rail diesel engine operated at a maximum speed of 4,500r/min with a 100Nm full load, and the oil film pressure was monitored while the engine was operating. The measured pressure was compared with calculations based on hydrodynamic lubrication (HL) theory.

A new Variable Valve Event and Lift (VVEL) system has been developed as an effective technology for reconciling environmental performance such as lowering the fuel consumption and exhaust emissions with driving performance. This system can continuously vary both the intake valve lift and event angle (valve opening duration) over a wide operating range to flexibly control the valve timing and lift for a substantial improvement in engine performance. In developing the variable valve lift control system, the essential merit is based on the fundmental configuration of multiple-link mechanism. However, it is required to resolve tribological issues for the specific mechnism. This paper describes the structure of the VVEL system and its operating and motion conversion principles. It also explains the mechanism analysis, dynamic stress analysis and lubrication simulation techniques used in developing the VVEL system, the materials adopted and the surface treatment techniques applied.

It is experimentally known that the surface color of bearing balls gradually becomes brown during long term operation of the bearings under appropriate lubrication conditions. That exhibits the possibility of an estimation method for residual life of ball bearings without any abnormal wear on the surfaces by precise color measurements. Therefore, we examined what set colors on bearing balls by surface observation using scanning electron microscopy and subsurface analysis using transmission electron microscopy. Results showed that an amorphous carbon layer had gradually covered ball surfaces during operation of the bearings. The layer not only changed ball color but also made overall ball shapes closer to a complete sphere. The report also introduces a uniquely developed color analyzer which enabled color measurements on metallic surfaces, such as the above-mentioned balls.

In order to establish standard method to evaluate cooling loss in combustion chamber of internal combustion engines based on measurement of instantaneous heat flux / wall temperature with higher response and accuracy than previously reported coaxial type thin-film temperature sensor by applying thin film fabrication technology based on PVD method (Physical Vapor Deposition method) which improved to realize higher responsiveness than the conventional sensor was developed by the authors, and it was confirmed that the sensor has sufficient durability in conditions in which the hydrogen jet and flame directly contacts surface of the sensor by thin-film material change. The influence of the improvement on the measurement accuracy was verified by numerical analysis including thermoproperty evaluation. In this report, the configuration of measurement system that can measure minute voltage from the sensor with low noise and high response is reported.

A simple method is frequently used to calculate a reciprocating engine’s bearing load from the measured cylinder pressure. However, it has become apparent that engine downsizing and weight reduction cannot be achieved easily if an engine is designed based on the simple method. Because of this, an actual load on a bearing was measured, and the measured load values were compared with a bearing load distribution calculated from cylinder pressure. As a result, it was found that some of actual loads were about half of the calculated ones at certain crank angles. The connecting rod’s elastic deformation was focused on as a factor behind such differences, and the rod’s deformation due to the engine’s explosion load was studied. As a result, it was found that the rod part of the engine’s connecting rod was bent by 0.2 mm and became doglegged. Additional investigation regarding these findings would allow further engine downsizing.

In order to verify cooling loss reduction effect of internal combustion engine, method for measuring wall surface temperature and heat flux with high accuracy is required. Various methods have been proposed for measuring the cooling loss from the combustion gas to the combustion chamber wall, newly coaxial type thin-film temperature sensor was developed for wall temperature and heat flux measurement by the authors. This sensor consists of thin-film and body and center wire have three junction positions in the case where three materials are different. Therefore, it is necessary to use the same materials for thin-film and body or thin-film and center wire to make two junction points. In this study, sputtering method that can be formed various kinds of alloy materials and film thickness of 0.1~1μm on the sensor surface was chosen.

As electric powertrain for electric vehicles (EVs) and hybrid vehicles (HVs) are becoming more efficient and smaller, rolling bearings for these vehicles should be capable of operating at higher speeds than those for internal combustion engines (ICEs). One key factor in predict fatigue endurance of such bearings is the oil film thickness on the bearing raceway grooves. Direct measurement of the oil film in operating machines is virtually unfeasible, while calculation of the oil film requires the input of precise temperature variation around the film. In this study, the oil film thickness on the bearing raceway grooves was calculated while in high-speed rotation by: (1) measuring the temperature profile of the bearing raceway outer ring; (2) calculating the temperature of the raceway groove using the basic formula for heat transfer; and (3) conducting an Elasto-Hydrodynamic Lubrication (EHL) analysis based on the temperature calculated in (2).

The authors have previously proposed a plume ignition and combustion concept (i.e., PCC combustion), in which a hydrogen fuel is directly injected to the combustion chamber in the latter half of compression stroke and forms a richer mixture plume. By combusting the plume, both cooling losses and NOx formation are reduced. In this study, thermal efficiency was substantially improved and NOx formation was reduced with PCC combustion by optimizing such characteristics as direction and diameter of the jets in combination with combustion of lean mixture. Output power declined due to the lean mixture, however, was recovered by supercharging while keeping NOx emissions at the same level. Thermal efficiency was further improved by slightly re-optimizing the jet conditions.

This paper describes a new variable valve system that enables continuous control of valve events, i.e. time periods when the valve is open. In this system, valve events are controlled by varying the camshaft angular speed by means of an offset between the center of the camshaft and that of the medium member that transfers crankshaft torque to the camshaft. The medium member, a rotating disk, has a drive pin to enable the transfer of torque. The system has a mechanism that produces an offset between the center of the rotating disk and that of the camshaft as well as an actuator that drives the mechanism. This makes it possible to develop a compact system that can be installed in existing DOHC direct-acting valve train engines without making any major cylinder head modifications.

Reducing friction in the crankshaft main bearings is an effective means of improving the fuel efficiency of reciprocating internal combustion engines. To realize these improvements, it is necessary to understand the lubricating conditions, in particular the oil film pressure distributions between crankshaft and bearings. In this study, we developed a thin-film pressure sensor and applied it to the measurement of engine main bearing oil film pressure in a 4-cylinder, 2.5 L gasoline engine. This thin-film sensor is applied directly to the bearing surface by sputtering, allowing for measurement of oil film pressure without changing the shape and rigidity of the bearing. Moreover, the sensor material and shape were optimized to minimize influence from strain and temperature on the oil film pressure measurement. Measurements were performed at the No. 2 and 5 main bearings.

The authors have previously proposed an engine system that uses a new piston-crank system incorporating a multiple-link mechanism to vary the piston's motion at top dead center and thereby obtain the optimum compression ratio matching the operating conditions. This multiple-link variable compression ratio (VCR) mechanism can be installed without increasing the engine size or weight substantially by selecting a suitable type of link mechanism and optimizing the detailed specifications. Previous papers by the authors have made clear the features of the VCR mechanism that facilitates continuously variable control of the compression ratio [1][2]. It was shown that engine friction attributable to piston-side thrust can be reduced through an upright orientation of the upper link in the expansion strokes.

A new variable valve event and lift (VVEL) system has been developed by applying a multiple-link mechanism. This VVEL system can continuously vary the valve event angle and lift over a wide range from an exceptional small event angle and small lift and to a large event angle and large lift. This capability offers the potential to improve fuel economy, power output, emissions and other parameters of engine performance. The valve lift characteristics obtained with the VVEL system consist of a synthesis of the oscillatory motion characteristics of the multiple-link mechanism and the oscillating cam profile. With the multiple-link mechanism, the angular velocity of the oscillating cams varies during valve lift, but the valve lift characteristics incorporate both gentle ramp sections and sharp lift sections, the same as a conventional engine.

A new variable valve actuation system that varies valve lift and timing events continuously has been devised and confirmed to substantially improve power and reduce fuel consumption when applied to a SI engine. The variable valve event and lift (VEL) system is a simple mechanism consisting of oscillating cams and linkages, enabling it to operate the valves smoothly even at high speed. Its compact size facilitates application to direct-acting valve trains and its ability to vary valve lift from a deactivated state (0) to a large lift amount allows the system to be used with a wide range of engine concepts. In this study, VEL was combined with a phase shifting function to enable the valve lift characteristic to be varied virtually arbitrarily, and test results showed that fuel consumption of a SI engine was reduced by nearly 10%.

A continuously variable valve event and lift (VEL) system, actuated by oscillating cams, can provide optimum lift and event angles matching the engine operating conditions, thereby improving fuel economy, exhaust emission performance and power output. The VEL system allows small lift and event angles even in the engine operating region where the required intake air volume is small and the influence of valvetrain friction is substantial, such as during idling. Therefore, the system can reduce friction to lower levels than conventional valvetrains, which works to improve fuel economy. On the other hand, a distinct feature of oscillating cams is that their sliding velocity is zero at the time of peak lift, which differs from the behavior of conventional rotating cams. For that reason, it is assumed that the friction and lubrication characteristics of oscillating cams may differ from those of conventional cams.