Search Results

Thermodynamic characteristics of premixed compression ignition combustions were clarified quantitatively by heat balance estimation. Heat balance was calculated from temperature, mole fractions of intake and exhaust gases, mass and properties of fuels. Heat balance estimation was conducted for three types of combustion; a conventional diesel combustion, a homogeneous charge compression ignition (HCCI) combustion; fuel is provided and mixed with air in an intake pipe in this case, and an extremely early injection type PREmixed lean DIesel Combustion (PREDIC). The results show that EGR should be applied for premixed compression ignition combustion to complete combustion at lower load conditions and to control ignition timing at higher load conditions. With an application of EGR, both HCCI and PREDIC showed low heat loss characteristics at lower load conditions up to 1/2 load.

The rate of air entrainment into the flame and the rate of heat release are thermodynamically calculated in a DI diesel engine: A two-zone model is proposed which uses as input data three measured values of cylinder pressure, flame temperature, and injection rate. The correlations between both rates under various conditions make it clear that the combustion during early and main periods of diffusion combustion is mainly controlled by air entrainment into the flame. The effects of injection pressure, piston configuration, and swirl intensity on the air entrainment are also studied. And the extent of mixing in the flame is evaluated by the equivalence ratio in the flame which is also obtained by the same model. The trends of exhausted NO and soot concentrations well correlate with the equivalence ratios in the flame and measured flame temperatures under all conditions studied.

One of the problems in HCCI combustion is a knocking in higher load conditions. It governs the high load limit, and it is suggested that the knock increases heat loss[1], because it breaks the thermal boundary layer. But it is not clear how much knock affects on heat loss in the HCCI combustion in various conditions, such as ignition timing and load. The motivation of this study is to clarify the ratio of heat loss caused by knock in HCCI engines. The heat loss from zero-dimensional calculations with modified heat transfer coefficient, which is considering the effect of knock by adding a term of cylinder pressure rising rate dp/dt, agreed well with the results from the thermodynamic analysis in various conditions. And the results show that it is possible to avoid heat loss by knock by controlling the ignition timing at appropriate timing after T.D.C. and it will be possible to expand the load range if knock can be avoided.

The purpose of this study is to improve low-temperature flow-properties of biodiesel fuels (BDF) by blending with ethanol and to analyze the combustion characteristics in a diesel engine fueled with BDF/ethanol blended fuel. Because ethanol has a lower solidifying temperature, higher oxygen content, lower cetane number, and higher volatility than BDF, ethanol blending would have a large effect on cold flow performance, mixture formation, ignition, combustion, and exhaust emissions. The engine experiments in the study were performed with a diesel engine and blends of BDF and ethanol at different blending ratios. The cold flow performance of the blended fuels was evaluated by determining the fuel cloud point. The experimental results show that the ethanol blending lowers the cloud point of the blended fuel and significantly reduces smoke emissions from the engine without deteriorating other emissions or thermal efficiency.

Since in-cylinder flame temperature has a direct effect on an engine's NOx characteristics, this phenomena has been studied in detail in a multi-cylinder DI diesel engine using a new method allowing the in-cylider temperature distribution to be measured by the two color method. An endoscope is installed in the combustion chamber and flame light introduced from the endoscope is divided into two colors by filters. The images of combustion phenomena using the two wavelengths are recorded with a framing streak camera which includes a CCD camera. The flame temperature and KL factor are immediately calculated by a computer using the two color images from the CCD camera. In the case of EGR, the test was conducted under 75% load conditions. The flame temperature was reduced according to an increase of EGR rate.

This paper describes the causality discussion such as the conflicted relationship in SRFNPH (simultaneous reduction of SFC, NOx, Particulate, HC) performance characteristics in HONDA-Pre-Chamber SI-CVCC, MITSUBISHI-DISC-SI-GDI, NISSAN DISC-CI-MK and CLEAN ENGINE-DISC-CI-OSKA-DH. The processes to be SRFNPH in these four combustions are shown as follows. M-GDI prepares LGF (low grade fumigation state in 15∼10% [O2] and 400∼600K temperature) state at ignition timing as same as N-MK Zone did. OSKA has no more this. In GDi, MK and OSKA, HGF (high grade fumigation state in 15∼10% [O2] and about 1000K temperature) state that is prepared by (STIM stratified ignition mechanism) and REABP (re-entrainment of active burned products) around the ignition timing was the state to form radical species and kinetic reaction. These are very similar condition created by CVCC-REABP which was made by high-speed burned gas jet from pre-chamber.

As a technology required for future commercial heavy-duty diesel engines, this study reexamines the potential of the multiple injection strategy for improving the thermal efficiency while maintaining low engine-out exhaust emissions with a high EGR rate of more than 50% and high boost pressure of 276.3 kPa abs under medium load conditions. The experiments were conducted with a single cylinder research engine. The engine was operated at BMEP of 0.8 MPa at a medium speed. Using multiple injections, the temporal and spatial in-cylinder temperature distribution was changed to investigate the effect on fuel consumption and exhaust emissions. The results showed that the multiple injection strategy combined with higher EGR rate could improve fuel consumption by about 3% due to the reduction of heat loss from the wall.

For reducing NOx emissions, EGR is effective, but an excessive EGR rate causes the deterioration of smoke emission. Here, we have defined the EGR rate before the smoke emission deterioration while the EGR rate is increasing as the limiting EGR rate. In this study, the high rate of EGR is demonstrated to reduce BSNOx. The adapted methods are a high fuel injection pressure such as 200 MPa, a high boost pressure as 451.3 kPa at 2 MPa BMEP, and the air intake port that maintains a high air flow rate so as to achieve low exhaust emissions. Furthermore, for withstanding 2 MPa BMEP of engine load and high boosting, a ductile cast iron (FCD) piston was used. As the final effect, the installations of the new air intake port increased the limiting EGR rate by 5%, and fuel injection pressure of 200 MPa raised the limiting EGR rate by an additional 5%. By the demonstration of increasing boost pressure to 450 kPa from 400 kPa, the limiting EGR rate was achieved to 50%.

The conflicting problems of fuel economy and NOx emissions in a spark ignition engines are discussed in relationship to the residual gas, volumetric efficiency and pumping loss as predicted by the gas exchange analysis which was described in a previous report (SAE P. 800535) . Predictions are made of : (1) the optimum valve timing for obtaining maximum volumetric efficiency; (2) the effect of valve timing on the residual gas and intake air charge and their relationships to the power output, fuel economy, and NO emissions; (3) the influence on combustibility and emissions of the main and auxiliary combustion chambers of a stratified charge engine; (4) the effects of the auxiliary intake valve air jet on the combustion of the lean combustion engine; (5) the effect on fuel economy of decreasing the pumping loss by adjusting valve timing and by adding EGR.

A theoretical model for predicting the evaporation process of liquid fuel sprays in both diesel and S.I. stratified charge engines is presented: The injected liquid fuel is assumed to break up into droplets with a certain time delay which is determined through careful experiments on the heat absorption process of injected fuel in a high temperature, high pressure inert atmosphere. The evaporation, heat absorption, and motion of these droplets are computed, together with the change of gas conditions inside the spray, by solving a coupled system of equations made up of heat and mass balance between droplets and gas. The effects of such parameters as the surrounding gas conditions, fuel properties, and spray characteristics on evaporation are investigated by the model. Reference is also made to the application of a predicted result to the calculation of burning rate in a direct injection diesel engine.

Some conceptual image of a diesel spray flame and its combustion promotion is shown based on the various interpretations of the enormous data obtained in our laboratory in these several years, on the flame temperature measurement by the two color method, the composition analysis by gas sampling, as well as the focus shadow photography, back illuminated photography and luminous photography by a high speed camera, on the diesel spray flame created in a large scale Rapid Compression Machine (diameter ϕ 200 mm thickness 40 mm) and a D-I engine (diameter (ϕ 95 mm)

Application of biodiesel fuel (BDF) to diesel engine is very effective to reduce CO2 emission, because biodiesel is carbon neutral in principle. However, biodiesels yield an increase in NOx emission from conventional diesel engine, compared with diesel fuel case. Therefore, some strategies are needed for meeting the future emission regulations when using biodiesel. In this study, rapeseed oil methyl ester (RME) was applied to diesel engine equipped with exhaust gas recirculation (EGR) system and NOx storage reduction (NSR) catalyst. NOx reduction rate of NSR catalyst was drastically decreased by using RME, even if injection quantity of RME for rich spike was enhanced. However, an increase in EGR rate could reduce NOx emission without the deterioration in smoke and PM emissions.

To identify ways of achieving good mixture formation and heat release in diesel spray combustion, we have performed Large Eddy Simulation (LES) using a detailed chemical reaction mechanism to study the temporal and spatial distribution of the local equivalence ratios and heat release rate. Here we characterize the effect of the fuel injection rate profile on these processes in the combustion chamber of a diesel engine. Two injection rate profiles are considered: a standard (STD) profile, which is a typical modern common rail injection profile, and the inverse delta (IVD) profile, which has the potential to suppress rich mixture formation in the spray tip region. Experimental data indicate that the formation of such mixtures may extend the duration of the late combustion period and thus reduce thermal efficiency.

In this paper, the flow patterns and velocity distributions of coolant flow around cylinder liners of diesel engine are studied by numerical calculation and experimental observation. The experiment is carried out by oil film method and direct observation with a transparent acrylic cylinder liner. The calculation is performed with the 3-dimensional model by FEM for fluid flow. The motion of coolant flow by calculation corresponds with the result by oil film method and direct observation with transparent cylinder liner. The visualization of the 3-dimensional calculation gives a good understanding about motion of coolant flow and pressure distribution in water chamber. This method is applied to improve the coolant flow with the stagnation around cylinder liner. The effect of improved design is confirmed by experiment. That is, there are no stagnations in the flow around cylinder liners.

A new technique was proposed for measuring instantaneous distributions of flame temperature and KL factor of luminous flames. Here the principle of the two-color method was used to calculate flame temperature and KL factor from the two-color densities of a film image taken on a nega-color film. We applied this technique to the high speed nega-color photographs of flames in a D. I. diesel engine operated with varying swirl ratios, and discussed the measured results of instantaneous distributions of flame temperature and KL factors.

A new method was developed which measures the atomization characteristics of a non-evaporating, axisymmetric diesel spray: The film image density of the high speed focused shadow photographs of a spray was analyzed based on the incident light extinction principle, and the Sauter mean diameter and the fuel concentration distribution were calculated from the image data and the measured injection rate with the help of the onion peeling model. The measured Sauter mean diameter showed good agreement with the diameter measured by the conventional immersion method, and also the measured fuel concentration distribution along the spray axis was proved to coincide well with the predicted result by Che one dimentional quasi-steady jet model except at a region near the spray tip.

The swirl velocity in the combustion bowl of a DI diesel engine was measured by means of laser doppler anemometry, varying the swirl intensity and engine speed. At the same time an axisymmetrical two dimensional laminar model for simulating the in-cylinder air motion was presented. The boundary condition of the flow near the wall was investigated by a comparison of predicted and measured swirl velocity, and as a result the free slip condition was found to be suitable for the present model. A comparison between measured and theoretical swirl velocity revealed that the secondary flow in the combustion bowl induced by an interaction between the squish and swirl flow transfers swirl velocities from points to points, causing a complex time variation of the swirl velocity at an observing point.

Premixed Lean Diesel Combustion (PREDIC) has very low NOx combustion because of early injection timing, for example, at -120 degrees ATDC; however, it has some problems. One problem is that so much fuel spray reaches the cylinder wall, which causes high HC emission and high fuel consumption. The other problem is that compression ignition timing control is difficult due to the dependence on the in-cylinder temperature. To solve these problems, an impingement spray system with two nozzles is attempted to obtain the spray increasing at the center of the combustion chamber instantaneously. This impingement spray system has two nozzles, which are located diagonally. Two sprays, one injected from each side injector, impinge each other at the center of the cylinder to create an air-fuel mixture.That is,this impingement spray system creates the air-fuel mixture by using the penetration of both sides of the sprays instead of early timing injection.

In heavy duty diesel engines, the waste heat recovery has attracted much attention as one of the technologies to improve fuel economy further. In this study, the available energy of the waste heat from a high boosted 6-cylinder heavy duty diesel engine which is equipped with a high pressure loop EGR system (HPL-EGR system) and low pressure loop EGR system (LPL-EGR system) was evaluated based on the second law of thermodynamics. The maximum potential of the waste heat recovery for improvement in brake thermal efficiency and the effect of the Rankine combined cycle on fuel economy were estimated for each single-stage turbocharging system (single-stage system) and 2-stage turbocharging system (2-stage system).

HCCI (Homogeneous Charge Compression Ignition) combustion results in very low NOx emissions, however, it is not without problems. One of them is that the heavy load operation range is limited by knock, due to an exceptionally high heat release rate. Knock increases the heat loss to the cylinder walls and piston, reducing thermal efficiency. To help solve these problems, direct (in-cylinder) water injection has been suggested to lower the local temperatures that seem to cause knock in HCCI. Water injection was adapted in an HCCI engine fueled with DME and Propane. Results showed that the indicated thermal efficiency was improved by about 2% (λ = 3.0, NA), and the operation range was expanded from 460kPa to 700kPa (NA) maintaining a low NOx level.