Search Results

Injury to the thorax is the predominant cause of fatalities in crash-involved automobile occupants over the age of 65, and many elderly-occupant automobile fatalities occur in crashes below compliance or consumer information test speeds. As the average age of the automotive population increases, thoracic injury prevention in lower severity crashes will play an increasingly important role in automobile safety. This study presents the results of a series of sled tests to investigate the thoracic deformation, kinematic, and injury responses of belted post-mortem human surrogates (PMHS, average age 44 years) and frontal anthropomorphic test devices (ATDs) in low-speed frontal crashes. Nine 29 km/h (three PMHS, three Hybrid III 50th% male ATD, three THOR-NT ATD) and three 38 km/h (one PMHS, two Hybrid III) frontal sled tests were performed to simulate an occupant seated in the right front passenger seat of a mid-sized sedan restrained with a standard (not force-limited) 3-point seatbelt.

Measurement of chest compression is vital to properly assessing injury risk for restraint systems. It directly relates chest loading to the risk of serious or fatal compression injury for the vital organs protected by the rib cage. Other measures of loading such as spinal acceleration or total restraint load do not separate how much of the force is applied to the rib cage, shoulders, or lumbar and cervical spines. Hybrid III chest compression is biofidelic for blunt impact of the sternum, but is “stiff” for belt loading. In this study, an analysis was conducted of two published crash reconstruction studies involving belted occupants. This provides a basis for comparing occupant injury risks with Hybrid III chest compression in similar exposures. Results from both data sources were similar and indicate that belt loading resulting in 40 mm Hybrid III chest compression represents a 20-25% risk of an AIS≥3 thoracic injury.

This report describes a series of experiments using Hexcel(TM) to limit the impact force in lateral abdominal impacts. Two hundred fourteen (214) anesthetized New Zealand White rabbits were impacted at 5 to 15 m/s using a pneumatic impactor. Injury responses from tests with a force-limiting impact interface (94 tests) were compared with the responses from tests with a rigid impact interface (120 tests) having the same level of lateral abdominal compression. The Hexcel had a length of 3 inches, the same diameter as the rigid impactor, and crushed at a constant force (pressure level of 232 kPa (33 psi)) once deformation was initiated. The results of these tests showed that the probability of serious abdominal injury did not change significantly with the Hexcel, even though peak pressures were reduced to as little as one third of their previous values.

Seventeen left lateral impact experiments were performed using anesthetized swine to determine the biomechanics of injury production in this impact mode. Two series of eight animals were used and one animal served as a control. In the first series of experiments, rigid thoracic and pelvic loading surfaces were separated by an “interplate gap” of 20.3 cm (8”). In the second series of experiments, the interplate gap was filled by a rigid plate mounted flush with the thoracic and pelvic loading surfaces. Impact velocities ranged from 7.2 to 15.0 m/s (about 15 to 30 mph). Injury patterns for the liver, spleen, and rib cage were significantly different in the two series of experiments (level of significance > 90%). The causative factor responsible for the different injury outcomes was the interplate gap. The conclusion of this report is that loading-surface discontinuities can cause significant injury.

The purpose of this paper is to compare the biofidelity rating schemes of ISO/TR9790 and the NHTSA Bio Rank System. This paper describes the development of new impact response corridors being proposed for ISO/TR9790 from the results of a recent series of side-impact sled tests. The response data were analyzed by methods consistent with ISO/TR9790, including normalization by impulse-momentum analysis and the elimination of subjects that sustained six or more rib fractures. Unlike ISO/TR9790, this paper proposes the elimination of the data from tests in which the timing and the sequence of loading of the individual impact plates were inconsistent compared to other tests conducted with the same impact wall configuration.

Analysis and validation of current scaling relationships and existing response corridors using animal surrogate test data is valuable, and may lead to the development of new or improved scaling relationships. For this reason, lateral pendulum impact testing of appropriate size cadaveric porcine surrogates of human 3-year-old, 6-year-old, 10-year-old, and 50th percentile male age equivalence, were performed at the thorax and abdomen body regions to compare swine test data to already established human lateral impact response corridors scaled from the 50th percentile human adult male to the pediatric level to establish viability of current scaling laws. Appropriate Porcine Surrogate Equivalents PSE for the human 3-year-old, 6-year-old, 10-year-old, and 50th percentile male, based on whole body mass, were established. A series of lateral impact thorax and abdomen pendulum testing was performed based on previously established scaled lateral impact assessment test protocols.

To date, several lateral impact studies (Bolte et al., 2000, 2003, Marth, 2002 and Compigne et al., 2004) have been performed on the shoulder to determine the response characteristics and injury threshold of the shoulder complex. Our understanding of the biomechanical response and injury tolerance of the shoulder would be improved if the results of these tests were combined. From a larger data base shoulder injury tolerance criteria can be developed as well as corridors for side impact dummies. Data from the study by Marth (2002, 12 tests) was combined with data from the previous studies. Twenty-two low speed tests (4.5 ± 0.7 m/s) and 9 high speed tests (6.7 ± 0.7 m/s) were selected from the combined data for developing corridors. Shoulder force, deflection and T1y acceleration corridors were developed using a minimization of cumulative variance technique.

This paper presents the results of biomechanical testing of the SID-IIs beta+-prototype dummy by the Occupant Safety Research Partnership. The purpose of this testing was to evaluate the dummy against its previously established biomechanical response corridors for its critical body regions. The response corridors were scaled from the 50th percentile adult male corridors defined in International Standards Organization Technical Report 9790 to corridors for a 5th percentile adult female, using established International Standards Organization procedures. Tests were performed for the head, neck, shoulder, thorax, abdomen and pelvis regions of the dummy. Testing included drop tests, pendulum impacts and sled tests. The biofidelity of the SID-IIs beta+-prototype was calculated using a weighted biomechanical test response procedure developed by the International Standards Organization.

Far-side lateral impacts were simulated using a Part 572 dummy and human cadavers to compare responses for several belt restraint configurations. Sled tests were conducted having a velocity change of 35 km/hr at a 10 g deceleration level. It was estimated from field data that a 35 km/hr velocity change of the laterally struck vehicle represents about an 80th percentile level for injury-producing lateral collisions. Subjects restrained by a three-point belt system with an outboard anchored diagonal shoulder belt (i.e., positioned over the shoulder opposite the side of impact) rotated out of the shoulder belt and onto the seat. The subject received some lateral restraint due to interaction with the shoulder belt and seatback. The subjects restrained by a three-point belt system with an inboard anchored diagonal shoulder belt (i.e., positioned over the shoulder on the side of impact) remained essentially upright due to shoulder belt interaction with the neck and/or head.

There has been recent progress over the past 10 years in research comparing 6-year-old thoracic and abdominal response of pediatric volunteers, pediatric post mortem human subjects (PMHS), animal surrogates, and 6-year-old ATDs. Although progress has been made to guide scaling laws of adult to pediatric thorax and abdomen data for use in ATD design and development of finite element models, further effort is needed, particularly with respect to lateral impacts. The objective of the current study was to use the impact response data of age equivalent swine from Yaek et al. (2018) to assess the validity of scaling laws used to develop lateral impact response corridors from adult porcine surrogate equivalents (PSE) to the 3-year-old, 6-year-old, and 10-year-old for the thorax and abdominal body regions.

This study continued the biomechanical investigations of forearm fractures caused by direct loading of steering-wheel airbags during the early stages of deployment. Twenty-four static deployments of driver airbags were conducted into the forearms of unembalmed whole cadavers using a range of airbags, including airbags that are depowered as allowed by the new federal requirements for frontal impact testing. In general, the depowered airbags showed a reduction in incidence and severity of forearm fractures compared to the pre-depowered airbags tested. Data from these twenty-four tests were combined with results from previous studies to develop a refined empirical model for fracture occurrence based on Average Distal Forearm Speed (ADFS), and a revised value for fifty-percent probability of forearm-bone fracture of 10.5 m/s. Bone mineral content, which is directly related to forearm tolerance, was found to be linearly related to arm mass.

Sled tests were conducted to investigate the dynamics of a Part 572 dummy as a sfunction of the belt restraint configuration and impact direction. The tests involved a 35 km/h velocity change and 10 g deceleration. An “opened” fixture, free of intervening surfaces, was oriented from frontal (0°), through oblique (±30°,±45°, ±60°), to full lateral (±90°). Restraint by only a lap belt resulted in the dummy's upper body rotating about the lap belt and continuing in the direction of sled deceleration. Restraint by a lap-shoulder belt greatly reduced upper-body displacement. However, the displacement and body loading were strongly dependent on the direction of deceleration, i.e., the orientation of the belt relative to the impact direction. When the belted shoulder was opposite the impact (0° to +90°), the belt retained the upper body for impact angles of 0° to 45°.

The introduction of energy absorbing steering systems has provided a substantial reduction of occupant injury in car crashes. However, the steering system remains the most important source of occupant injury. Injury associated with steering assembly contact is due to high exposure; energy absorbing steering systems reduce the risk of injury for drivers when compared to the injury risk of right front passengers. Our investigation addressed loading of the upper abdominal region by the steering wheel rim using a physiological model for study of soft tissue injury. Injury to the liver was related to the abdominal compression response associated with rim loading. Although liver injury correlated somewhat with peak abdominal compression, a better correlation was found when the rate of compression was also considered. Force limiting by the steering wheel, not by column compression, most strongly influenced the outcome of abdominal injury.

Injury and disability associated with head (brain), neck (spinal cord) and facial injury account for 61.7% of the total societal Harm in the most recent estimate of motor-vehicle related crash injuries. This paper discusses the need for accurate information on translational and rotational acceleration of the head as the first step in critiquing the Head Injury Criterion (HIC) and other injury predictive methods, and developing a fuller understanding of brain and spinal cord injury mechanisms. A measurement system has been developed using linear accelerometers to accurately determine the 3D translational and rotational acceleration of the Hybrid III dummy head. Our concept has been to use the conventional triaxial accelerometer in the dummy's head to assess translational acceleration, and three rows of in-line linear accelerometers and a least squares analysis to compute statistical best-fits for the rotational acceleration about three orthogonal axes.

Data from the National Crash Severity Study (NCSS) has been analyzed with respect to lateral impacts. Accident variables, vehicle variables, and occupant variables, and their interactions have been considered. Emphasis has been placed on occupant variables, especially occupant injury patterns. This report is mainly a compendium of the data, including a comparison of the NCSS statistics with those from France, Germany, and Great Britain. Overall, these lateral impact statistics are quite similar to results of other field accident studies, which is an interesting observation given the diverse vehicle and driver populations and the differing traffic situations experienced by those populations. Conclusions have been drawn regarding typical lateral impact situations and the effectiveness of seatbelts in lateral impacts.

The study was directed toward improving our understanding how postcrash column compression and steering wheel deformation relate to the driver interaction with an energy absorbing steering system during automotive collisions. Frontal sled tests conducted at 19–37 km/h investigated the Part 572 antropomorphic dummy interaction with a ball-sleeve column steering assembly over a range of column angles and surrogate postures. Neither column compression nor steering wheel deformation correlated with the mechanical severity of the test surrogate interaction with the steering system. The steering wheel deformed before the column compressed and the degree of wheel deformation strongly depended on the surrogate load distribution, the steering wheel being an important energy absorbing element.

In 1998, Rouhana et al. described development of a new device, called the IR-TRACC (InfraRed - Telescoping Rod for Assessment of Chest Compression). In its original concept, the IR-TRACC uses two infrared LEDs inside of a telescoping rod to measure deflection. One LED serves as a light transmitter and the other as a light receiver. The output from the receiver LED is converted to a linear function of chest compression using an analog circuit. Tests have been performed with IR-TRACC units at various labs around the world since 1998. A first-generation IR-TRACC system was retrofit into a Q3 dummy by TNO. Similarly, a mid sized male Hybrid III dummy thorax and a small female Hybrid III dummy thorax have been designed by First Technology Safety Systems (FTSS) such that each contains 4 second-generation IR-TRACC units. The second-generation IR-TRACC is the result of continued development by FTSS, especially in the areas of the analysis circuit, manufacturing and calibration methods.

Studies conducted in the 1970's suggested that inflatable belt restraints might provide a high level of occupant protection based on experiments with dummies, cadavers and volunteers. Although inflating the belt was one factor which contributed to achieving these experimental results, much of the reported performance was associated with other features in the restraint system. Exploratory experiments with the Hybrid III dummy indicated similar trends to previous studies, belt inflation reducing dummy response amplitudes by pretensioning and energy absorption while reducing displacement. The potential advantage of an increased loaded area by an inflatable belt could not be objectively demonstrated from previous studies or from dummy responses. Clearly, belt inflation can be one component of a belt restraint system which tends to reduce test response amplitudes. However, other belt system configurations have demonstrated similar test response amplitudes.

Airbag deployments are associated with loud noise of short duration, called impulse noise. Research performed in the late 1960's and early 1970's established several criteria for assessment of the risk of impulse noise-induced hearing loss for military weapons and general exposures. These criteria were modified for airbag noise in the early 1970's, but field accident statistics and experimental results with human volunteers exposed to airbags do not seem to agree with the criteria. More recent research on impulse noise from weapons firing, in particular that of Price & Kalb of the US Army Research Laboratory, has led to development of a mathematical model of the ear. This model incorporates transfer functions which alter the incident sound pressure through various parts of the ear. It also calculates a function, called the “hazard”, that is a measure of mechanical fatigue of the hair cells in the inner ear.

High-amplitude, short-duration noise is called impulse noise. A large body of literature on impulse noise has been developed primarily by military researchers for multiple exposures such as those caused by weapons firing. Some research into the impulse noise associated with air bag deployments was performed in the late 1960's and early 1970's to ascertain the risk of hearing loss. Several criteria for risk of noise-induced hearing loss were proposed and much was learned about the sources of the noise. Unfortunately, the instrumentation used to measure the noise in many of those studies lacked adequate low frequency response characteristics. Perhaps more importantly, results from experiments with human volunteers do not seem to agree with the proposed criteria. For this study, a new system consisting of commercially available pressure transducers and microphones was assembled and a new software package was developed.