Search Results

Cycle resolved LDA measurements of the tangential velocity component, made along a diameter of two combustion chambers (toroidal and square) during the compression stroke of a diesel engine operating at 600 and 1000 rpm, are discussed. Indirect measurements of lateral integral length scales determined by single point autocorrelation technique are presented. Finally direct measurements of lateral integral length scales made by a new laser doppler velocimeter system based on two probe volume technique are reported.

A modified version of KIVA II code was used to perform three-dimensional calculations of combustion in a DI diesel engine. Both an ignition delay submodel and a different formulation of the fuel reaction rate were implemented and tested. The experiments were carried out on a single cylinder D.I. diesel of 0.75 I displacement equipped with sensors to detect injection characteristics and indicated pressure. A fast acting sampling valve was also installed in the combustion chamber to allow the measurement of main pollutants during the combustion cycle, by an ensemble average technique. Computational and experimental results are compared and the discrepancies are discussed. Today the demand for light duty engines that produce less emission and consume less fuel is increasing. Thus, if limits on CO2 emissions are established, the direct injection diesel engine for light duty applications will become an attractive option.

The paper describes some experiments carried out on two d.i. Diesel engines running with insulated pistons. Three different thermal barriers were tested; namely, a stainless steel cup, a Si3N4 cup and a stainless steel piston crown. The combustion process was characterized by heat release calculation and ignition delay measurements. The experiments showed that the indicated efficiency is not affected by thermal insulation adoption, Nox level increases while smoke level decreases consistently.

This paper reports some results of a research carried out under part sponsorship of the Commission of the European Communities in the framework of the Joule II program. A twelve fuels matrix, derived from very different formulation techniques like hydrotreatment, Fisher Tropsch process, oligomerization and addition of oxygenated compounds to the straight run was tested. Istituto Motori performed tests on a turbocharged, after-cooled, direct injection diesel engine of two liter total displacement. It was equipped with an electronic E.G.R. system. Tests were performed in steady state conditions, representative of transient European schedules. Regulated and unregulated emissions was measured. Further tests were performed in cold conditions, the coolant temperature at the engine outlet was kept below 10°C in order to enhance the behavior of different fuels in producing regulated and unregulated emissions.

Three dimensional computations of Diesel combustion were performed using a modified version of Kiva II code. The autoignition and combustion model were tuned on a set of experimental conditions, changing the engine design, the operating conditions and the fuel characteristics. The sensitivity of the model to the different test cases is acceptable and the experimental trends are well reproduced. In addition the peak of pressure and temperature computed by the code are quite close to the experimental values, as well as the pressure derivatives. Once tuned the combustion model constants, different but simple formulations for the soot formation and oxidation processes were implemented in the code and compared with the experimental measurements obtained both with fast sampling technique and two colors method. These formulations were found unable to give good prediction in a large range of engine operating conditions, even if the model tuning may be very good for each test point.

Aim of the present paper was an evaluation of the importance of some engine parameters (intake gas flow and injection parameters) on the approach of Premixed Low Temperature Combustion (PLTC) conditions with the same efficiency of a conventional diesel cycle and ultra-low pollutant emissions. The results have demonstrated that the control of PLTC mode is very difficult and the engine parameters play a critical role on the exhaust pollutant emissions, indicating that further massive research activities are needed to reach reliable practical applications.

This paper reports on the first successful tests performed on a production D.I. Diesel engine using wood pyrolysis oil (WPO). As reported in literature, any attempt to directly replace Diesel fuel with WPO required extensive modifications to the engine injection system, in order to overcome the intrinsic limits of the oil (poor self-ignition, high acidity and viscosity): new materials, additional pilot injection systems, careful procedures of start-up and shutdown were needed to obtain acceptable operation. Aim of the present work was to assess the limits of utilization of WPO in a strictly stock engine. Therefore, while no modifications at all were carried out on the engine, the efforts were addressed to make the WPO compatible with light-duty Diesel engines. Several long-running tests were performed on a single-cylinder engine, with: blends of WPO with different percentage of oxygenated compounds micro-emulsions of WPO in Diesel fuel standard (commercial) Diesel fuel.

This paper reports some results on the performance of an advanced common rail (CR) DI diesel engine burning 12 model diesel fuels. The experiments were carried out within a co-operative research program “NeDeNeF” (New Diesel Engines and New Diesel Fuels), partly sponsored by the Commission of European Communities. Partners of the project with Istituto Motori (IM) were: FEV (Germany), VTT (Finland), NTUA (Greece), Brunel University (UK), Fortum (Finland), LAT (Greece) under the coordination of the IFP (France). The matrix of twelve fuels was prepared by the fuel producer partner (Fortum). The research program of the Diesel Engines and Fuels Department of Istituto Motori aimed at assessing the effect of fuel quality on exhaust emissions. The engine employed in the tests was a Fiat four-cylinder DI CR diesel engine, EURO3 version, of 1.9 litre, installed on Fiat Group class C Cars (1350kg of mass).

This paper presents the performances of a modern DI diesel engine, equipped with a Common Rail injection system, fed on blends of an advanced diesel fuel (base fuel) and Diethylene-Glycol-Dimethyl-Ether (Diglyme - C6H14O3). The base fuel was a reformulated diesel fuel with low aromatic and sulfur content. Three blends with different volumetric percentage of Diglyme (10, 20 and 30%) in the base fuel were prepared and tested. The engine was a FIAT M724, installed in a Alfa Romeo 156 1.9 JTD, with a Bosch Common Rail injection system (EDC-15C). At the exhaust of the engine, soot, NOx, HC, CO, and CO2 were measured. The experiments represent the potential of diesel reformulation technology with synthetic fuels coupled with the new diesel technology generation.

In the present paper some results, obtained by the use of modern numerical C.F.D tools, are presented. In particular, starting from the experimental characterization of a conventional design D.I. diesel engine, the empirical constants of the different submodels were tuned to obtain satisfactory results in some key test conditions. After that, in the same points of the engine performance map, the following parameters were systematically varied: Fuel injection system design and operating conditions Intake swirl level Exhaust gas recirculation level. The influence of each parameter on combustion evolution is discussed and the most promising trend for the engine optimization is presented. Taking into account the model formulations limits, the results obtained suggest, from a theoretical point of view, that “common rail” equipped light duty diesel engines are suitable to meet the future European emission regulations.

In the present paper the combustion process in a modern second generation Common Rail Diesel engine for light duty application is experimentally and numerically investigated. An improved version of the KIVA3V-Release 2 code was used for the simulations. To model the combustion process, a detailed kinetic scheme involving 57 species and 290 equations, based on the n-heptane combustion, was used, interfacing the KIVA3V code with the CHEMKIN-II chemistry package. The full set of equations is concurrently solved in each computational cell by different solvers with the final aim of obtaining a locally adaptative code: local choices are undertaken in terms of time steps as well as in terms of the employed solvers. To reduce computational time, the code was parallelized: this parallelization is mainly focused on the chemical subroutines, considering that they are responsible for more than the 95% of the computing.

The effect of fuel injection strategy and charge dilution on NOx and soot emissions has been investigated with a modern DI diesel engine. Particulate mass has been measured by a standard smoke meter and soot particles have been characterized by means of time-resolved Laser Induced Incandescence (LII) at the exhaust of the engine. Two steady-state test points have been selected, representative of low and medium load conditions. The influence of the different engine management strategies has been assessed, highlighting the potential of unconventional operating modes to meet forthcoming emission limits.

Tangential component of velocity and turbulence were measured in three locations in the re-entrant combustion chamber of a motored single-cylinder d.i. Diesel engine (0.435 liter, 21:1 compression ratio) using a Laser Doppler Velocimetry system. Moreover, a modified LDV system with two-probe volume was used to measure directly lateral integral length scales of the velocity tangential component at two engine speeds. The measurements were made on a horizontal plane at 5 mm below the engine head from 100 degrees before TDC to 60 degrees after TDC of both the compression and expansion strokes. The engine was motored at 1,000 and 1,500 rpm respectively. An ensemble-averaging technique was performed to analyze the instantaneous velocity information supplied by two Burst Spectrum Analyzers. The lateral integral length scale was obtained from the integral of the spatial correlation coefficient of the velocity fluctuation for different separation.

The paper aims at providing information about the spray structure and its evolution within the combustion chamber of a heavy duty direct injection (HDDI) diesel engine. The spray penetration is investigated, firstly under quiescent conditions, injecting the fuel in a vessel under ambient temperature and controlled back pressure by both numerical and experimental analyses using the STAR-CD code and the imaging technique, respectively. Experimental results of fuel injection rate, fuel penetration, and spray cone angle are used as initial conditions to the code and for the comparison of predictions. The experimental investigation is carried out using a mechanical injection pump equipped by the heavy duty eight cylinder engine. Only one of its plungers has been activated and the fuel is discharged through a seven holes mechanical injector, 0.40 mm in diameter.

Cetane number, sulphur content and aromatic structure of Automotive Diesel Oil (ADO) were changed to assess their influence on emissions of light duty direct injection Diesel engine. The detailed chemical analysis of particulate soluble fraction allows to quantify the P.A.Hs emission. In addition also the aldehydes and volatile organic compounds were measured in the gaseous phase. The sulphur content of the fuel and its aromatic structure strongly influence particulate emission. The insoluble fraction of the particulate rises with an increase of the high sulphur content ADOs with about the same back end volatility. Unburned P.A.Hs control P.A.Hs emission at the part loads typical of normalized schedules for emission testing of light duty vehicles in Europe. Finally the level of emissions of benzene and 1-3 butadiene is comparable to the total P.A.Hs emission.

The aim of the present paper is to provide an insight into the fluid dynamic processes that occur during the air/fuel mixture formation period in direct injection diesel engines. An experimental and numerical investigation has been performed to analyse the mixing process between an evaporating diesel spray and a swirl air flow under realistic engine conditions. Experimental tests have been carried out spraying the fuel within an optically accessible prototype 2-stroke Diesel engine equipped with an external combustion chamber having cylindrical shape. The intake air flow, coming from the engine cylinder, is forced within the combustion chamber by means of a tangential duct generating a well structured swirl flow similar to that developing in a real light duty diesel engine with a high swirl ratio. A micro-sac 5-hole, 0.13 mm diameter, 150° spray angle electro-hydraulic injector supplies the fuel by a common rail injection system able to manage multiple injection strategies.

This paper describes a characterisation of the combustion behaviour in an optical Common Rail diesel engine fed by different advanced fuels, via the application of the two-colour pyrometry technique. The acquired images were processed in order to calculate the instantaneous flame temperature and soot volume fraction. For the measurements, a single test point was chosen as representative of the reference four-cylinder engine performance in the European driven cycle ECE+EUDC. The test point was the 1500 rpm and 22 mm3/stroke of injected fuel volume, correspondent to the engine point of 1500rpm @ 5 bar of BMEP for the 4-cylinder engine of 1.9L of displacement. As general overview, the flame luminosity from combustion of the fuel injected during pilot injection was always below the threshold of sensitivity of the detection system.

Selected measurements of the in-cylinder soot loading and the gaseous combustion products for ten different innovative fuels, burned in a D.I. diesel engine are presented and discussed. All the fuels which were tested have a very low sulfur content, so the insoluble fraction of the particulate is mainly composed of soot. Two different measure techniques are applied: the two-color pyrometry optical method and the fast sampling of gaseous products in the combustion chamber. A priori and experimental uncertainties relative to the reduction of the data obtained with the two-color measurements are preliminarily investigated.

The formation and oxidation of soot, light and heavy hydrocarbons, CO, CO2 and NOx in a D.I. diesel engine have been studied by means of direct fast sampling and chemical analysis of the combustion products collected during the combustion cycle. Particular attention has been paid to the histories of each fuel hydrocarbon class analyzing the chemical transformations that the paraffins, and monoaromatic and polyaromatic compounds, contained in a diesel fuel oil, undergo during the combustion cycle. This approach is able to give information on the origin of soot and heavy hydrocarbon emission from a diesel engine. The concentration of the heavy hydrocarbons decreases during the early stages of the combustion cycle and their profile corresponds roughly to the fuel disappearance rate because of the chemical similarity with the fuel compounds.

The optimization of combustion system of a single-cylinder d.i. diesel engine, representative of heavy-duty family, is discussed. The characterization of in-cylinder fluid motion of a conventional straight-sided and a re-entrant combustion chamber, carried out by LDA technique, is presented. Engine tests, using the same chambers and sacless nozzles with different holes diameter and appropriate spray angle, have been performed. Strong reduction of smoke and HC emissions has been obtained, remaining unchanged the engine performance.