Search Results

The goal of this theoretical-experimental work is to model two-dimensional, unsteady (and steady) two phase flow combustion in internal combustion engines (and steady reactors) and to test and improve the model with parallel experimental programs. The purpose of this research is to make more detailed current understanding of this important family of combustion problems and to aid the development of cleaner and more efficient engines. In this paper, preliminary theoretical-experimental results of our efforts toward the stated goal are presented. The theoretical results are preliminary but prove the feasibility of detailed computations of combustion in internal combustion engines and show how informative such computations can be. In a section of this paper, preliminary results are reported of detailed computations of two-dimensional, unsteady sprays penetrating and vaporizing into an inert gas in a closed volume (without combustion).

Flame fronts were examined in a premixed-charge, spark-ignition, ported engine using a two-dimensional visualization technique with 10 nanoseconds time resolution and 200 microns best spatial resolution. The engine had a pancake chamber, a compression ratio of 8, a TDC swirl number of 4 and was operated at 300 to 3000 rpm with stoichiometric and lean propane/air mixtures. The measurements were made far from, and near to, the cylinder wall. A pulsed laser sheet was passed through the engine and the light scattered by sub-micron TiO2 or ZrO2 seeding particles was collected by a 100 x 100 diode array with fields of view of 1 cm x 1 cm, 2 cm x 2 cm, and 9 cm x 9 cm. The thickness of the flame front is as small as, or smaller than, the 200 micron best resolution of the measurements thus confirming that premixed-charge engine turbulent flames generally appear to be wrinkled laminar flames.

The structure of turbulent flames was examined in a premixed-charge, spark-ignition ported engine using a three-dimensional visualization technique with 10 ns time resolution and 350 µm best spatial resolution. The engine had a pancake chamber, a compression ratio of 8, a TDC swirl number of 4 and was operated at 300, 1200 and 2400 rpm with stoichiometric and lean propane/air mixtures. The second and third harmonic beams of an Nd-YAG laser (532 nm and 355 nm), along with the two strongest beams (first Stokes (683 nm) and first anti-Stokes (436 nm)) from a hydrogen Raman shifter pumped by the second harmonic were used to create four parallel laser sheets each of less than 300 microns thickness. The laser sheets were passed through a transparent quartz ring in the cylinder head parallel to the piston top with vertical separations between successive sheets ranging from 1.5 to 0.9 mm.

Recent measurements by of gas intake flows and exhaust pressure in a motored, ported, single-cylinder engine with strong swirl and roll have been used as boundary conditions to a three-dimensional, transient computer simulation of the flow within the cylinder. For each condition, the calculation is continued over several engine cycles until the periodic solution is obtained. The computed TDC tangential velocity and turbulence intensity are then compared with measured ones. A technique is described to evaluate scavenging efficiency, the fraction of charge that remains in the cylinder over later cycles and the degree of mixedness of fresh and residual charge. For this motored ported engine, it is found that the scavenging efficiency is very low (19.4% at 1200 RPM) and the inflow from the exhaust ports is very significant. For practical ported engines with combustion, the scavenging efficiency is much higher but the inflows from exhaust ports are still expected to be significant.

Engine-out, cold-start (from 20°C) UHC emissions from a contemporary 2.0 4-cylinder engine with swirl control were measured with FID and FT-IR. The steady-state, end of test operation was 1500 rpm, 2.6 bar BMEP (25% load) and stoichiometric mixture. Four fuel systems were employed pintle-type port-injected gasoline, air-forced port-injected gasoline, port-injected propane, and premixed propane. These fuel systems were chosen to separate effects of fuel atomization, vaporization, and fuel-air mixing. Each system was optimized with respect to injector targeting, injection timing, mixture enrichment, and spark advance. Open-valve injection timing increased UHC emissions more with the pintle-type injector than with the air-forced, system. UHC emissions with propane injection were minimized with open valve injection.

For practical, extensive 3-D computations for engine improvements, each physical submodel needs to be the simplest that is compatible with the accuracy of all other physical submodels and of the numerics. The addition of one progress variable controlled by one Arrhenius term is shown to be adequate to reproduce Diesel ignition delay in 2-D and 3-D computations. The rest of the model is that used for years by the authors to optimize combustion in reciprocating and rotary engines with premixed and non-premixed charges, including all of its model constants. This minimal Diesel autoignition submodel reproduces well trends and magnitudes of ignition delay versus chamber temperature and pressure. As in experiments, it is found that multiple ignition sources develop in rapid succession at various locations around the fuel spray after the first ignition event.

A recently developed laser Doppler velocimetry system for making two-point spatial correlation measurements of velocity fluctuations has been applied to the turbulent flow field of an IC engine. Fluctuation integral length scales have been measured within the clearance volume of a ported, single cylinder engine with a disc-shaped chamber and a compression ratio of 8.0. The engine was motored at 600 rpm and the engine flow field had a swirl ratio at top dead center of approximately 4. These measurements were made at the center of the clearance height at three-quarters of the cylinder radius. The integral length scale was found to reach a minimum of approximately one-fifth of the clearance height near IDC. Comparison of the results obtained using this technique with the integral length scales measured in engines by other authors using different methods gives agreement to within a factor of two.

The exciplex fluorescence technique has been used to separately visualize liquid and vapor phase fuel in engines since its development by Melton. However, as a fluorescence technique it has the potential to be quantitative and the underlying assumptions have been outlined by Melton. An initial quantitative application of the TMPD/naphthalene system, based on these assumptions, applied to a hollow-cone spray in a two-stroke engine, indicated that it substantially over-estimates the concentration of fuel vapor about TDC. The reasons for the discrepancy were investigated and it was concluded that a major factor is the effect of temperature on the photophysics of the species involved. Thus the absorption spectra of the exciplex dopants were determined at temperatures up to 700 K. These experiments showed that the increase in absorption with temperature above 500 K is responsible for the failure of the earlier calibration.

Two-Dimensional, single-shot spontaneous Raman measurements of methane concentration were performed in an optically accessible engine after direct injection with the use of modified air-assisted injector. The spatial resolution of the measurements was determined by the thickness of the laser sheet which was 0.8 mm. The error in the methane number density measurement was determined by the noise in the intensified camera output and was 16% of pure methane number density at the experimental conditions. Effective suppression of the stray light background was the main experimental difficulty. Satisfactory results were acquired only when the spark plug was substituted by a plug covered with a velvet-like, black piece of cloth. These preliminary results show that, for the specific engine configuration, fast mixing of the charge yields a very mild stratification after the end of injection.

Atomization and full-cone sprays from single cylindrical orifices are considered. The following subjects are reviewed: the structure of the breakup region; the structure of the far field; modern models that, given the outcome of the breakup process, compute the steady and transient of sprays; some comparisons with detailed measurements; and some practical applications. The following conclusions are reached: the spray breakup and the development regions are the most relevant in engine applications; the inner structure of the breakup region is still largely unknown; two- and three-dimensional spray models are available but remain mostly untested, particularly in their vaporization and combustion components, in part because of a lack of accurate measurements in controlled engine-type environments; engine applications of such models are, nonetheless, recommended for very valuable learning, interpretative, and exploratory studies, but not for predictions.

Planar instantaneous fuel concentration measurements were made by laser-induced fluorescence of 3-pentanone in the spark gap just prior to ignition in a direct-injection spark-ignition engine operating at a light load, highly stratified condition. The distribution of the average equivalence ratio in a circle of 1.9 mm diameter centered on the spark plug showed that a large fraction of the cycles had an equivalence ratio below the lean limit, yet acceptable combustion was achieved in those cycles. Further, weak correlation was found between the local average equivalence ratio near the spark plug and the time required to achieved a 100 kPa pressure rise above the motoring pressure, as well as other parameters which characterize the early stages of combustion. The cause for this behavior is assessed to be mixture motion during the spark discharge which continually convects fresh mixture through the spark gap during breakdown.

Cycle-resolved LDV measurements of tangential and radial velocities were made in a ported engine within four piston cups. One cup was centered circular, one off-center circular, one centered square and one off-center square. The engine speed was 1200 rpm, the compression ratio 10.8, the squish area 75% and the TDC swirl ratio 4 for a pancake chamber. The velocity measurements were made at four depths in two axial sections. Near TDC in the centered circular cup, the profile of the ensemble-averaged tangential velocity tends to solid body with a swirl ratio of 12.5. In the centered square cup, the same velocity tends to solid-body profile along the short section and to top-hat profile along the outer part of the long section. The corresponding TDC swirl ratios are 11.3 and 5.5 due to mass conservation. The trends are similar but more complex in the off-center circular and square cups. In the centered circular cup, the swirl center is close to the cylinder axis near TDC.

Results of experiments performed on a direct-injection two-stroke engine using an air-assisted injector are presented. Pressure measurements in both the engine cylinder and injector body coupled with backlit photographs of the spray provide a qualitative understanding of the spray dynamics from the oscillating poppet system. The temporal evolution of the spatial distribution of both liquid and vapor fuel were measured within the cylinder using the Exciplex technique with a new dopant which is suitable for tracing gasoline. However, a temperature dependence of the vapor phase fluorescence was found that limits the direct quantitative interpretation of the images. Investigation of a number of realizations of the vapor field at a time typical of ignition for a stratified-charge engine shows a high degree of cycle to cycle variability with some cycles exhibiting a high level of charge stratification.

Efforts are reported to reproduce the distribution of liquid and vapor fuel from a pulsating hollow-cone liquid-only injector measured by the planar exciplex technique within the head cup of a motored ported single-cylinder engine operated at 1600 rpm with high swirl and a squish ratio of 75%. The injector, cup and cylinder were coaxial. The measurements show that shortly after the beginning of the injection the maximum liquid and vapor fuel concentrations are along the axis but also that the spray achieves substantial radial and axial penetrations. The engine flowfield without injection had previously been characterized by LDV and PIV and so had been the injector and its spray in constant pressure environments so that little arbitrariness was left in reproducing the spray in the engine. Two spray models were used. In one the large drops produced by the break up of the liquid sheet were introduced into the numerical field at the injector exit nearly with the poppet seat angle.

Results are presented of 3-D computations of direct injection of gaseous methane and of liquid tetradecane through a multi-hole injector into a Diesel engine. The study focusses on the distribution of fuel/air ratio within the resulting gas and spray jets under typical Diesel conditions prior to ignition. It is shown that for a significant time after start of injection, the fraction of the vapor fuel which is in richer-than-flammable mixtures is greater in gas jets than in sprays. For methane injection, it is also shown that changing some of the flow conditions in the engine or going to a poppet-type injector, does not result in improved mixing. An explanation of these results is provided also through an analysis of the self-similar gas jet and 2-D computations of gas and spray jets into constant pressure gas. A scaling for time and axial distance in the self-similar gas jet also clarifies the results.

Combustion in a divided-chamber, stratified-charge engine is considered and flame and pressure results obtained with a two-dimensional, unsteady model are compared with corresponding engine data. The model is applied to eight engine conditions differing in speed, load and size of the prechamber orifice. The model employs one overall chemical reaction rate, the k-ε representation of turbulence, and a wall heat loss proportional to the heat release. The computed results are shown to be in good agreement with the experimental ones in spite of the complexity of the problem and the early stages of detailed model validation studies. They are also shown to compare somewhat better than earlier ones obtained with an ad-hoc jet turbulence model. Both studies prove the importance of the prechamber jet to the overall combustion process for the particular engine investigated.

A three-dimensional model for flows and combustion in reciprocating and rotary engines is applied to a direct-injection stratified-charge rotary engine to identify the main parameters that control its burning rate. It is concluded that the orientation of the six sprays of the main injector with respect to the air stream is important to enhance vaporization and the production of flammable mixture. In particular, no spray should be in the wake of any other spray. It was predicted that if such a condition is respected, the indicated efficiency would increase by some 6% at higher loads and 2% at lower loads. The computations led to the design of a new injector tip that has since yielded slightly better efficiency gains than predicted.

Simultaneous fuel distribution images (by shadowgraph and laser-induced fluorescence) and cylinder pressure measurements are reported for a combusting stratified-charge engine with a square cup in the head at 800 RPM and light load for two spark locations with and without swirl. Air-assisted direct-injection occurred from 130°-150° after bottom dead center (ABDC) and ignition was at 148° ABDC. The engine is ported and injection and combustion take place every 6th cycle. The complicated interaction of the squish, fuel/air jet, square cup, spark plug geometry and weak tumble gives rise to a weak crossflow toward the intake side of the engine with no swirl, but toward the exhaust side in the presence of strong swirl, skewing the spray slightly to that side.

In a previous study, the authors compared the fuel-air mixing characteristics of gas jets and sprays in Diesel engine environments in the absence of combustion. A three-dimensional model for flows and sprays was used. It was shown that mixing was slower in gas jets relative to fast-evaporating sprays. In this study, which is an extension of the previous one, the direct-injection of gasesous methane, gaseous tetradecane and liquid tetradecane are studied using the same three-dimensional model. This study concentrates on combustion. It is shown that the fuel-air mixing rate and hence the burning rate are initially slower with gas injection.