Search Results

While the Diesel Particulate Filter (DPF) is actually a quasi-standard equipment in the European Diesel passenger cars market, an interesting solution to fulfill NOx emission limits for the next EU 6 legislation is the application of a Selective Catalytic Reduction (SCR) system on the exhaust line, to drastically reduce NOx emissions. In this context, one of the main issues is the performance of the SCR system during cold start and warm up phases of the engine. The exhaust temperature is too low to allow thermal activation of the reactor and, consequently, to promote high conversion efficiency and significant NOx concentration reduction. This is increasingly evident the smaller the engine displacement, because of its lower exhaust system temperature (reduced gross power while producing the same net power, i.e., higher efficiency).

The use of piezoelectric cylinder pressure sensors is very popular during engine testing, but cylinder pressure information is becoming mandatory also in several on-board applications, where Low Temperature Combustion (LTC) approaches require a feedback control of combustion, due to poor combustion stability and the risk of knock or misfire. Several manufacturers showed the capability to develop solutions for cylinder pressure sensing in on-board automotive and aeronautical applications, and some of them have been patented. The most straight-forward approach seems the application of a piezo-electric washer as a replacement of the original part equipping the spark plug; the injector could also be used to transfer the cylinder pressure information to the piezoelectric quartz, in diesel or Gasoline Direct Injections (GDI) engines.

This work aims at analyzing the fluid dynamic characteristics of a Ducati 4 valves SI engine, for racing motorcycle, during the intake and compression strokes, focusing on the correlation between steady state flow test data (experiments and simulations) and transient CFD simulation results, including the effect of variable valve actuation strategies with independent intake valve actuation. Several steady state flow test data were available in terms of maps of the discharge, tumble and swirl coefficients, at any combination of asymmetric lifts of the two intake valves. From these steady state data it can be argued that asymmetric strategies could enhance engine full load and part load operation characteristics, by exploiting favourable trade off occurring between the opposing needs for high mass flow rate and high charge motion intensity.

Knock is a non-deterministic phenomenon and its intensity is typically defined by a non-symmetrical distribution, under fixed operating conditions. A statistical approach is therefore the correct way to study knock features. Typically, intrinsically deterministic knock models need to artificially introduce Cycle-to-Cycle Variation (CCV) of relevant combustion parameters, or of cycle initial conditions, to generate different knock intensity values for a given operating condition. Their output is limited to the percentage of knocking cycles, once the user imposes an arbitrary knock intensity threshold to define the correlation between the number of knocking events and the Spark Advance (SA). In the first part of the paper, a statistical analysis of knock intensity is carried out: for different values of SA, the probability distributions of an experimental Knock Index (KI) are self-compared, and the characteristics of some percentiles are highlighted.

Specific power and efficiency of gasoline engines are influenced by factors such as compression ratio and Spark Advance (SA) regulation. These factors influence the combustion development over the crank angle: the trade-off between performance and the risk of irreversible damages is still a key element in the design of both high-performance (racing) and low-consumption engines. This paper presents a novel approach to the problem, with the objective of defining a damage-related and operating conditions-independent index. The methodology is based on the combined analysis of indicating parameters, such as Cumulated Heat Release (CHR), Indicated Mean Effective Pressure (IMEP) and 50% Mass Fraction Burned (MFB50), and typical knock detection parameters, estimated by means of the in-cylinder pressure sensor signal. Knocking combustions have several consequences, therefore they can be detected in many ways.

Combustion control is one of the key factors to obtain better performance and lower pollutants emissions, for diesel, spark ignition and HCCI engines. This paper describes a real-time indicating system based on commercially available hardware and software, which allows the real-time evaluation of Indicated Mean Effective Pressure (IMEP) and Rate of Heat Release (ROHR) related parameters, such as 50%MFB, cylinder by cylinder, cycle by cycle. This kind of information is crucial for engine mapping and can be very important also for rapid control prototyping purposes. The project objective is to create a system able to process in-cylinder pressure signals in the angular domain without the need for crankshaft encoder, for example using as angular reference the signal coming from a standard equipment sensor wheel. This feature can be useful both for test bench and on-board tests.

Combustion control is assuming a crucial role in reducing engine tailpipe emissions and maximizing performance. The number of actuations influencing the combustion is increasing, and, as a consequence, the control parameters calibrations is becoming challenging. One of the most effective factors influencing performance and efficiency is the combustion phasing: gasoline engines Electronic Control Units (ECU) manage the Spark Advance (SA) in order to set the optimal combustion phase. SA optimal values are usually determined by means of calibration procedures carried out on the test bench by changing SA values while monitoring Brake and Indicated Mean Effective Pressure (BMEP, IMEP), Brake Specific Fuel Consumption (BSFC) and pollutant emissions. The effect of SA on combustion is stochastic, due to the cycle-to-cycle variation: the analysis of mean values requires many engine cycles to be significant of the performance obtained with the given control setting.

Combustion control is one of the keys to obtain better performance and pollutants emission, both for diesel, spark ignition and HCCI engines. This paper presents a low-cost and high performance system based on commercially available hardware and software, which allows the implementation of control and diagnostic strategies based on combustions analysis, with the typical Rapid Control Prototyping (RCP) advantages (user friendly development tools, real time calibration, etc.). Information on the combustion process can be accessed by means of an indicating sensor such as an in-cylinder pressure transducer, or a ionization current measurement system, depending on the application. The signal must be sampled with a fast sampling system within a given crank angle window. It is then possible to process the input signal, in order to evaluate diagnostic or control indexes which can be calculated before the end of the same engine cycle, and finally used to correct the engine control parameters.

Lean operation of spark ignition engines is a promising strategy for increasing thermal efficiency and minimize emissions. Variability on the other hand is one of the main shortcomings in these conditions. In this context, the present study looks at the interaction between the spark produced by a J-type plug and the surrounding fluid flow. A combined experimental and numerical approach was implemented so as to provide insight into the phenomena related to the ignition process. A sweep of cross-flow velocity of air was performed on a dedicated test rig that allowed accurate control of the volumetric flow and pressure. This last parameter was varied from ambient to 10 bar, so as to investigate conditions closer to real-world engine applications. Optical diagnostics were applied for better characterization of the arc in different operating conditions. The spatial and temporal evolution of the arc was visualized with high-speed camera to estimate the length, width and stretching.

This paper reports investigations on diesel jet transients, accounting for internal nozzle flow and needle motion. The calculations are performed with Large Eddy Simulation (LES) turbulence model by coupling the internal and external multiphase flows simultaneously. Short and multiple injection strategies are commonly used in internal combustion engines. Their features are significantly different from those generally found in steady state conditions, which have been extensively studied in the past, however, these conditions are seldom reached in modern engines. Recent researches have shown that residual gas can be ingested in the injector sac after the end-of-injection (EOI) and undesired dribbles can be produced. Moreover, a new injection event behaves differently at the start-of-injection (SOI) depending on the sac initial condition, and the initial spray development can be affected for the first few tens of μs.

The challenge of industrial carbon footprint reduction is led by the engine manufacturers that are developing new technologies and fuels to lower CO2 emissions. Although the deployment of relevant investments for the development of battery electric vehicles, diesel, and gasoline cars are still widely used, especially for their longer operating range, faster refueling, and lower cost. For this reason, more efficient traditional internal combustion engines can guide the transition towards new propulsion systems. In this document, the innovative piston damage and exhaust gas temperature models previously developed by the authors are reversed and coupled to manage the combustion process, increasing the overall energy conversion efficiency. The instantaneous piston erosion and the exhaust gas temperature at the turbine inlet are evaluated according to the models’ estimation which manages both the spark advance, and the target lambda.

This work investigates the effects of cavitation on spray characteristics by comparing measurements of liquid and vapor penetration as well as ignition delay and lift-off length. A smoothed-inlet, converging nozzle (nominal KS1.5) was compared to a sharp-edged nozzle (nominal K0) in a constant-volume combustion vessel under thermodynamic conditions consistent with modern compression ignition engines. Within the near-nozzle region, the K0 nozzle displayed larger radial dispersion of the liquid as compared to the KS1.5 nozzle, and shorter axial liquid penetration. Moving downstream, the KS1.5 jet growth rate increased, eventually reaching a growth rate similar to the K0 nozzle while maintaining a smaller radial width. The increasing spreading angle in the far field creates a virtual origin, or mixing offset, several millimeters downstream for the KS1.5 nozzle.

The paper reports on the optical investigation of a multiple spark ignition system carried out in a closed vessel in inert gas, and in an optical access engine in firing condition. The ignition system features a plug-top ignition coil with integrated electronics which is capable of multi-spark discharges (MSD) with short dwell time. First, the ignition system has been characterized in constant ambient conditions, at different pressure levels. The profile of the energy released by the spark and the cumulated value has been determined by measuring the fundamental electrical parameters. A high speed camera has been used to visualize the time evolution of the electric arc discharge to highlight its shape and position variability. The multiple spark system has then been mounted on an optical access engine with port fuel injection (PFI) to study the combustion characteristics in lean conditions with single and multiple discharges.

Currently, conventional spark-ignition engines are unfit to satisfy the growing customer requirements on efficiency while complying with the legislations on pollutant emissions. New ignition systems are being developed to extend the engine stable operating range towards increasing lean conditions. Among these, the Radio-Frequency corona igniters represent an interesting solution for the capability to promote the combustion in a much wider region than the one involved by the traditional spark channel. Moreover, the flame kernel development is enhanced by means of the production of non-thermal plasma, where low-temperature active radicals are ignition promoters. However, at low pressure and at high voltage the low temperature plasma benefits can be lost due to occurrences of spark-like events. Recently, RF barrier discharge igniters (BDI) have been investigated for the ability to prevent the arc formation thanks to a strong-breakdown resistance.

The new real driving emission cycles and the growing adoption of turbocharged GDI engines are directing the automotive technology towards the use of innovative solutions aimed at reducing environmental impact and increasing engine efficiency. Water injection is a solution that has received particular attention in recent years, because it allows to achieve fuel savings while meeting the most stringent emissions regulations. Water is able to reduce the temperature of the gases inside the cylinder, coupled with the beneficial effect of preventing knock occurrences. Moreover, water dilutes combustion, and varies the specific heat ratio of the working fluid; this allows the use of higher compression ratios, with more advanced and optimal spark timing, as well as eliminating the need of fuel enrichment at high load. Computational fluid dynamics simulations are a powerful tool to provide more in-depth details on the thermo-fluid dynamics involved in engine operations with water injection.

This work involves modeling internal and near-nozzle flows of a gasoline direct injection (GDI) nozzle. The Engine Combustion Network (ECN) Spray G condition has been considered for these simulations using the nominal geometry of the Spray G injector. First, best practices for numerical simulation of the two-phase flow evolution inside and the near-nozzle regions of the Spray G injector are presented for the peak needle lift. The mass flow rate prediction for peak needle lift was in reasonable agreement with experimental data available in the ECN database. Liquid plume targeting angle and liquid penetration estimates showed promising agreement with experimental observations. The capability to assess the influence of different thermodynamic conditions on the two-phase flow nature was established by predicting non-flashing and flashing phenomena.

The present work concerns the analysis of a concept for a new variable valve actuation system for internal combustion engines, denoted HVC (Hydraulic Valve Control system). The system is an electro-hydraulic device which aims at minimizing the power consumption required for the valve actuation. Unlike lost motion devices, where the excess pumped oil is wasted in order to control the lift profile, the HVC system uses a reduced quantity of energy to ensure the actual lift profile. For that reason interesting potentialities to increase the global fuel conversion efficiency of the engine are expected, in addition to the benefits deriving from the control flexibility. The HVC system has been modeled by means of an hydraulic simulation tool, useful for the dynamic analysis of mechanical and hydraulic systems. In this work the main elements of the device will be described and their relevant modeling parameters will be discussed.

The mixture composition heavily influences the combustion process of Port Fuel Injection (PFI) engines. The local mixture air-index at the spark plug is closely related to combustion instabilities and the cycle-by-cycle Indicated Mean Effective Pressure (IMEP) Coefficient of Variation (CoV) well correlates with the variability of the flame kernel development. The needs of reducing the engine emissions and consumption push the engine manufactures to implement techniques providing a better control of the mixture quality in terms of homogeneity and variability. Simulating the mixture formation of a PFI engine by means of CFD techniques is a critical issue, since involved phenomena are highly heterogeneous and a two phase flow must be considered. The aim of the paper is to present a multi-cycle methodology for the simulation of the injection and the mixture formation processes of high performance PFI engine, based on the validation of all the main physical sub-models involved.

Missing combustions phenomena have been studied for a long time, in order to achieve on board diagnosis capability, due to their effect on emissions and after treatment system life. A detailed analysis of missing combustion causes can be used beyond the On Board Diagnostic (OBD) regulations observance aim, both for modeling and diagnostic purposes. The combustion taking place in a faulty cylinder right after the fault happens is usually different with respect to a standard one: both the residual gas fraction and the fuel film effect have strong influences on post-faulty combustions. Parameters used to describe these phenomena can then be evaluated analyzing the engine post-faulty behavior. The same analysis may lead to a better fault description, thus improving diagnosis performance.

Engine test benches are crucial instruments to perform tests on internal combustion engines. Since many factors affect tests results, an engine test bench is usually equipped with several conditioning systems (oil, water and air temperature, air humidity, etc.), in order to maintain the controlled variables to the target values, throughout the test duration. The conditioning systems are often independently controlled by means of dedicated programmable logic controllers (PLC), but a centralized model-based management approach could offer several advantages in terms of promptness and accuracy. This work presents the application of such control methodology to oil, water, and HVAC (heating, ventilating, and air conditioning) conditioning systems, where each actuator is managed coupling model-based open loop controls to closed loop actions.