Search Results

This paper describes the ZENITH Nano-Satellite cum planetary atmospheric entry vehicle, called CanSat, the first Nano-Satellite project that has been developed by Delhi Technological University (Formerly Delhi College of Engineering), India. The satellite will function for monitoring the concentrations of various gases in the atmosphere. For this, the satellite consists of arduino microcontroller interfaced with the various Micro-electromechanical system (MEMS) gas sensors for measuring the concentrations of various gases such as carbon dioxide, carbon monoxide, methane, nitrous oxides, ozone, etc. The data obtained from the CanSat will be transmitted to the ground station where all the data will be stored and also the locations will be stored using GPS sensor. The academic goal of this project is to recruit students to the field of space science and technology.

Data obtained when harvesting with a combine equipped with a yield monitor were used to develop yield maps. A prototype yield monitor was developed that uses a combination of light emitters and receivers mounted in a rectangular frame. The monitor was mounted in the combine in the top of the clean grain elevator. As grain flows through the monitor, a voltage change proportional to light reduction was recorded. This voltage was then correlated to grain flow rate. At the same time, site-specific location was recorded using the global positioning satellites (GPS) system. The location data, yield monitor output, cutting width, and combine forward speed were stored in a spreadsheet format. The data were then used to prepare the yield maps.

This SAE Standard specifies requirements and design guidelines for electrical wiring systems of less than 50 V and cable diameters from 0.35 to 19 mm2 used on off-road, self-propelled earthmoving machines as defined in SAE J1116 and agricultural tractors as defined in ASAE S390.

This SAE Standard specifies requirements and design guidelines for electrical wiring systems of less than 50 V and cable diameters from 0.35 to 19 mm2 used on off-road, self-propelled earthmoving machines as defined in SAE J1116 and agricultural tractors as defined in ASAE S390.

Defining the wireless marketing is a challenge in today's world. Companies interested in capitalizing on the wireless market for automatic vehicle location (AVL) have a number of wireless options from which to choose. One of the most exciting wireless combinations is GPS (Global Positioning System) and cellular systems. The Global Positioning System (GPS)/cellular combination can be used to create Automatic Vehicle Location systems for a wide variety of applications, from fleet management to personal security. Unfortunately, no single wireless network fits all the possible AVL applications, and choosing the best network for an application is essential to system performance. This paper reviews the current wireless technologies available in the market-place, discusses why ATX chose the wireless technology it uses, and gazes into the crystal ball to forecast the future of wireless.

Pedestrians A method of locating a charging target device (vehicle) in a parking lot scenario by the evaluation of Received Signal Strength Indication (RSSI) of the Dedicated Short Range Communications (DSRC) signal and Global Positioning System (GPS) data is proposed in this paper. A metric call Location Image (LI) is defined based on the RSSI received from each charger and the physical location of the parking associated to that charger. The central parking lot processor logs the GPS coordinates and LI received from the vehicle. Each pairing attempt by a vehicle loads a new LI into the central processor's database. Utilizing the LI and the proposed methods the vehicle will achieve expedited charger to system pairing while in the company of multiple chargers.

This paper reviews today's aircraft wing production assembly methodology and technologies as well as innovative ideas for advancing the high-level wing assembly state-of-the-art. Automated wing assembly systems are only being utilized to rivet/fasten first level subassemblies like panels, spars, and ribs. All other high level assembly tasks are performed manually, incurring associated increases in recurring costs due to production inefficiencies, long lead times, expensive rate tooling, and difficult assembly tasks performed inside small wing compartments. Existing assembly methods, process parameters, and the process characteristics of manual, machine, and man/machine systems provide many opportunities for improving wing assembly.

Due to the part size and technological limitations of the available assembly equipment, traditional wing manufacturing has consisted of a three stage process. Parts are first manually tacked together in an assembly jig, They are then removed from the jig, rotated horizontally and craned into an automated fastening machine. Finally they are removed from the fastening machines and craned to a third station where the manual tacks are removed and the parts are prepped for final wing box assembly. With the advent of electromagnetic riveting (EMR) and the traveling yoke assembly machine this traditional approach has been replaced with single station processing. Wing panels and spars can now be automatically tacked together under continuous clamp up in their assembly jigs using EMR. This eliminates the requirement for disassembly, debur and cleaning required with the manual process.

Through this work, Wind River and Airbiquity look to enable secure and intelligent software updates and data management for these vehicles through over-the-air (OTA) programming technology. The work may also lead to similar solutions for traditional aerospace and unmanned aircraft system (UAS) industries.

Rankine powerplant advantages are found to fit best applications that call for long maintenance free life, or where the heat energy is essentially free as in bottoming and topping cycles, or in special environments as undersea or space. Worthy applications suggested on the basis of potential market size and ability to satisfy customer imposed cost and performance are: automotive and tank accessory power systems (APS), transportable refrigeration, portable power supply (GPS), standby power, remote site power, and home air conditioner drive. The automotive APS and a 1 1/2 kWe GPS are further analyzed. The APS can offer attractive features to the automobile user, including the possibility of reducing pollution from spark ignition engine. The GPS is an example showing high cost effectiveness for long operating times. It is recommended that marketing and cost studies continue, and that working fluid and heat exchanger technologies be accentuated.

Visual Place Recognition (VPR) excels at providing a good location prior for autonomous vehicles to initialize the map-based visual SLAM system, especially when the environment changes after a long term. Condition change and viewpoint change, which influences features extracted from images, are two of the major challenges in recognizing a visited place. Existing VPR methods focus on developing the robustness of global feature to address them but ignore the benefits that local feature can auxiliarily offer. Therefore, we introduce a novel hierarchical place recognition method with both global and local features deriving from homologous VLAD to improve the VPR performance. Our model is weak supervised by GPS label and we design a fine-tuning strategy with a coupled triplet loss to make the model more suitable for extracting local features.

The automotive and the aerospace industries are constantly looking at optimizing their production with cost effective and versatile material separation processes suitable for machining three-dimensional parts (3D) in all kind of materials. Automation with robots has become quite common for manufacturing large serials of parts with constant quality and accuracy, avoiding risks for the operator. This paper will deal with robotised waterjet cutting used to cut automotive floor carpets and other interior trim parts such as headliners, instrument panels, door panels, trunk liners, acoustical insulation, parcel shelves and some fiberglass reinforced components. Furthermore we will talk about robotised routing, a suitable alternative for machining some of the above mentioned components. We will also describe abrasive waterjet, ideal for cutting 3D components made of metals, alloys and thick composites.

This paper has been withdrawn and is no longer available.

At WCX World Congress Experience you’ll participate in live panel discussions, Q&As, keynotes, and breakout sessions with researchers and leaders across the industry.