Search Results

Cylinder pressure-based combustion control is widely introduced for passenger cars. Benefits include enhanced emission robustness to fuel quality variation, reduced fuel consumption due to more accurate (multi-pulse) fuel injection, and minimized after treatment size. In addition, it enables the introduction of advanced, high-efficient combustion concepts. The application in truck engines is foreseen, but challenges need to be overcome related to durability, increased system costs, and impact on the cylinder head. In this paper, a new single cylinder pressure sensor concept for heavy-duty Diesel engines is presented. Compared to previous studies, this work focuses on heavy-duty Diesel powertrains, which are characterized by a relatively flexible crank shaft in contrast to the existing passenger car applications.

Heavy-duty diesel engines are used in a wide range of applications. For varying operating environments, the engine and aftertreatment system must comply with the real-world emission legislation limits. Simultaneously, minimal fuel consumption and good drivability are crucial for economic competitiveness and usability. Meeting these requirements takes substantial development and calibration effort, and complying with regulations results in a trade-off between emissions and fuel consumption. TNO's Integrated Emission Management (IEM) strategy finds online, the cost-optimal point in this trade-off and is able to deal with variations in operating conditions, while complying with legislation limits. Based on the actual state of the engine and aftertreatment system, an optimal engine operating point is computed using a model-based optimal-control algorithm.

Heavy-duty diesel engines are used in different application areas, like long-haul, city distribution, dump truck and building and construction industry. For these wide variety of areas, the engine performance needs to comply with the real-world legislation limits and should simultaneously have a low fuel consumption and good drivability. Meeting these requirements takes substantial development and calibration effort, where an optimal fuel consumption for each application is not always met in practice. TNO's Integrated Emission Management (IEM) strategy, is able to deal with these variations in operating conditions, while meeting legislation limits and obtaining on-line cost optimization. Based on the actual state of the engine and aftertreatment, optimal air-path setpoints are computed, which balances EGR and SCR usage.

In the past decade, SCR deNOx technology with urea injection has grown to maturity. European OEMs will apply SCR deNOx to meet future heavy-duty emissions legislation starting with EURO-4 (2005/2006). Numerous research programs in Europe and the US have shown a variety of system layouts and control strategies. The main differences are formed by: the engine-out NOx calibration the application of an NO to NO2 catalyst open-loop or closed-loop urea dosage control. This paper gives an overview of possible SCR system configurations that are required for different stages of future emission legislation. Engine-out NOx emission is strongly influenced by ambient conditions. Projections in this study show that a combination of cold climate and a wintergrade fuel is the most severe: it may lead to 30% lower engine-out NOx emission with respect to laboratory conditions.

A new cost-based control strategy is presented that optimizes engine-aftertreatment performance under all operating conditions. This Integrated Emission Management strategy minimizes fuel consumption within the set emission limits by on-line adjustment of air management based on the actual state of the exhaust gas aftertreatment system. Following a model-based approach, Integrated Emission Management offers a framework for future control strategy development. This approach alleviates calibration complexity, since it allows to make optimal trade-offs in an operational cost sense. The potential of the presented cost-optimal control strategy is demonstrated for a modern heavy-duty Euro VI engine. The studied diesel engine is equipped with cooled EGR, Variable Geometry Turbocharger, and a DPF-SCR aftertreatment system.

This paper presents the first results of an experimental study into a hybrid combustion concept for next-generation heavy-duty diesel engines. In this hybrid concept, at low load operating conditions, the engine is run in Pre-mixed Charge Compression Ignition (PCCI) mode, whereas at high load conventional CI combustion is applied. This study was done with standard diesel fuel on a flexible multi-cylinder heavy-duty test platform. This platform is based on a 12.9-liter, 390 kW heavy-duty diesel engine that is equipped with a combination of a supercharger, a two-stage turbocharging system and low-pressure and high-pressure EGR circuitry. Furthermore, Variable Valve Actuation (VVA) hardware is installed to have sufficient control authority. Dedicated pistons, injector nozzles and VVA cam were selected to enable PCCI combustion for a late DI injection strategy, free of wall-wetting problems.

This paper presents a model-based control and calibration design method for online cost-based optimization of engine-aftertreatment operation under all operating conditions. The so-called Integrated Emission Management (IEM) strategy online minimizes the fuel and AbBlue consumption. Based on the actual state of engine and aftertreatment systems, optimal air management settings are determined for EGR-SCR balancing. Following a model-based approach, the strategy allows for a systematic control design and calibration procedure for engine and aftertreatment systems. The potential of this time efficient method is demonstrated by experiments for a heavy-duty Euro-VI engine. The Integrated Emission Management strategy is developed and calibrated offline over a cold and hot World Harmonized Transient Cycle (WHTC) for the set emission targets. The total IEM development and calibration process takes approximately 20 weeks from model identification to the acceptance tests.

This paper presents a cylinder pressure-based control (CPBC) system for conventional diesel combustion with high EGR levels. Besides the commonly applied heat release estimation, the CPBC system is extended with a new virtual NOx and PM sensor. Using available cylinder pressure information, these emissions are estimated using a physically based combustion model. This opens the route to advanced On-Board Diagnostics and to optimized fuel consumption and emissions during all operating conditions. The potential of closed-loop CA50 and IMEP control is demonstrated on a multi-cylinder heavy-duty EGR engine. For uncalibrated injectors and fuel variations, the combustion control system makes the engine performance robust for the applied variations and reduces the need for a time-consuming calibration process. Cylinder balancing is shown to enable auto-calibration of fuel injectors and to enhance fuel flexibility.

A promising SCR-only solution is presented to meet post-2010 NOx emission targets for heavy duty applications. The proposed concept is based on an engine from a EURO IV SCR application, which is considered optimal with respect to fuel economy and costs. The addition of advanced SCR after treatment comprising a standard and a close-coupled SCR catalyst offers a feasible emission solution, especially suited for EURO VI. In this paper, results of a simulation study are presented. This study concentrates on optimizing SCR deNOx performance. Simulation results of cold start FTP and WHTC test cycles are presented to demonstrate the potential of the close-coupled SCR concept. Comparison with measured engine out emissions of an EGR engine shows that a close-coupled SCR catalyst potentially has NOx reduction performance as good as EGR. Practical issues regarding the use of an SCR catalyst in close-coupled position will be addressed, as well as engine and exhaust layout.

A model-based control approach is proposed to give proper reference for the feed-forward combustion control of Partially Pre-mixed Combustion (PPC) engines. The current study presents a simplified first principal model, which has been developed to provide a base estimation of the ignition properties. This model is used to describe the behavior of a single-cylinder heavy-duty diesel engine fueled with a mix of bio-butanol and n-heptane (80vol% bio-butanol and 20 vol% n-heptane). The model has been validated at 8 bar gross Indicated Mean Effective Pressure (gIMEP) in PPC mode. Inlet temperature and pressure have been varied to test the model capabilities. First the experiments were conducted to generate reference points with BH80 under PPC conditions. And then CFD simulations were conducted to give initial parameter set up, e.g. fuel distribution, zone dividing, for the multi-zone model.

Reaching EUROVI Heavy Duty emission limits will result in more testing time for developing control and OBD algorithms than to reach EUROV emissions. It is likely that these algorithms have to be adapted for a WHTC (World Heavy Duty Transient Cycle) for EUROVI. This cycle when started cold can only be performed a limited times a day on the engine testbench, because of the cooling down time. The development time and cost increases to reach EUROVI emission levels. Accurate simulation tools can reduce the time and costs by reducing the amount of tests required on the testbench. In order to use simulation tools to develop pre calibrations, the models must be fitted and validated. This paper will focus on the fit process of an SCR (Selective Catalytic Reduction) model. A unique test procedure has been developed to characterize an SCR catalyst using an engine testbench in ±2 days. This data is used in an automatic SCR fit tool to obtain the model parameters in a few days.

The goal of this work was to investigate the possibilities of applying high EGR rates with low NOx and PM emission levels on a two-stage turbocharged 12 liter heavy duty diesel engine. The EGR is applied by using a long and short route EGR system. For the ESC operating points A25 and C100 EGR is applied, such that the NOx emission is 0.5 g/kWh. Lowest PM level and BSFC are achieved when long route EGR is applied in A25 and short route is applied in C100. Increasing the fuel line pressure is an effective way to reduce PM at high EGR rate engine running conditions. At a fuel line pressure of 2400 bar PM emission are 0.06 g/kWh for A25 and 0.54 g/kWh for C100. At C100 the PM reduction coincides with also a significant fuel consumption improvement. Retarding the injection timing at C100 can improve the PM emission further to a level of 0.13 g/kWh at the expense of an increase in BSFC.